User`s manual

ManualsBrandsChristie ManualsProjectorCS70-D100U

RPMS-D100U/UF,

CS50-D100U, CS70-D100U/UF

54-003766-01P (10/04) 1 of 6

Lamp Replacement

- Instruction Sheet -

Introduction

Applies to RPMS-D100U/UF (38-GFX204-01, 38-GFX205-01, 38-GFX206-01, 38-GFX207-01),

CS70-D100U/UF (38-GFX052-xx, 38-GFX053-xx) and CS50-D100U (38-GFX054-xx).

RPMS-D100U/UF, CS50-D100U and CS70-D100U/UF units use two identical 100W UHP

(Ultra High Pressure) lamps and can be operated with both lamps ON (Dual Lamp Operation

mode) or with one lamp ON (Single Lamp Operation mode). The projector will automatically

switch modes to maintain continuous operation. Use the following information and

instructions when replacing the lamps in these projectors.

NOTE: Refer to the User’s Manual (54-017188-xxP) for more information on Lamp Operation

Modes.

Components Required

Lamp Replacement Kit #03-240088-xxP (kit includes 100W UHP lamp, instructions, lamp warranty claim form,

RMA form, service safety sheet)

Phillips #1 screwdriver

Safety and Warning Guidelines

Please read before proceeding with lamp replacement

•

Read the Lamp Replacement procedure in its entirety before proceeding.

•

Never stick hands into an empty lamp compartment while the projector is still

plugged into an AC outlet.

•

Use caution when handling lamps. Lamps, even those that have been through a

cool down period, are still hot due to the heat emitted from the other operational lamp.

•

Do not touch the glass surface of the lamp. Grip the lamp by the handle only.

Fingerprints left on the glass surface of a lamp can lead to an intense accumulation of

heat called “hotspots” that could potentially cause the lamp to explode. Wear clean,

lint-free cotton gloves when handling the lamp to prevent fingerprints.

Instructions

When should lamps be replaced?

Typically, aging lamps decrease slightly in their intensity. You can check the number of hours

each lamp has been in use by checking Lamp Hours in individual lamp submenus. From the

Lamp menu, you can also set a Lamp Limit (max 20,000 hours) and enable the projector to

send a lamp replacement, warning message when it’s powered on.

At anytime during operation, you can check the status of a lamp by checking the Lamp Strike

Status in individual lamp submenus — More, Lamp 1 or More, Lamp 2. You will see one of six

states: “Good”, “Cooling Fan #3 Failed”, “Cooling Fan #5 Failed, “Interlock Tripped”, “Failed

to Strike” and “Turned Off Unexpectedly”. A status of “failed to strike” or “turned off

unexpectedly” indicates a failure that requires further investigation and may or may not be

directly related to the lamp.

Summary of content (6 pages)

PAGE 1
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - Introduction Applies to RPMS-D100U/UF (38-GFX204-01, 38-GFX205-01, 38-GFX206-01, 38-GFX207-01), CS70-D100U/UF (38-GFX052-xx, 38-GFX053-xx) and CS50-D100U (38-GFX054-xx). RPMS-D100U/UF, CS50-D100U and CS70-D100U/UF units use two identical 100W UHP (Ultra High Pressure) lamps and can be operated with both lamps ON (Dual Lamp Operation mode) or with one lamp ON (Single Lamp Operation mode).
PAGE 2
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - If you have ruled out the cause being an aged lamp or another component in the projector, it may indicate that your lamp has prematurely burned out or failed for some other reason (check status LEDs and/or error codes through RS-232, if possible). Burned out lamps or lamps that have failed due to some characteristic flaw should be replaced, as soon as possible.
PAGE 3
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - HOT SWAP ALTERNATIVE: If you choose to replace a lamp without disrupting the current presentation, it is recommended that you switch to the Single Lamp mode for the lamp you are not going to replace. Then proceed with Step 2. 2. OPEN LAMP COMPARTMENT: Loosen the two captive screws on the lamp door you want to open. Swing the door open. (NOTE: Each lamp door is spring-loaded and needs to be held open during lamp replacement.
PAGE 4
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - 3. REMOVE LAMP: Loosen the two captive screws securing the lamp in the lamp module. (Figure 2.) Holding the lamp door open with one hand, grasp the lamp handle and pull straight up to remove the lamp. (Figure 3.) The lamp disconnects from the terminal block much like unplugging something from an outlet. Figure 2. DO NOT touch the glass surface of the lamp. Set it aside for proper disposal once it has cooled down. Figure 3.
PAGE 5
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - Figure 4. 5. CLOSE LAMP DOOR: Once the lamp is inserted, carefully close the spring-loaded lamp door and lock it by tightening the two lamp door captive screws. Watch your fingers! The lamp door is spring-loaded and will snap close. Use caution when closing the lamp door. 6. TURN THE PROJECTOR ON (IF APPLICABLE) OR SWITCH BACK TO THE ORIGINAL LAMP OPERATION MODE: Press Power* to turn the projector on.
PAGE 6
RPMS-D100U/UF, CS50-D100U, CS70-D100U/UF Lamp Replacement - Instruction Sheet - Technical Support NORTH AMERICA CHRISTIE Digital Systems, Inc. 809 Wellington St. North Kitchener, Ontario, Canada N2G 4Y7 Tel. 519-744-8005 (General) Toll Free 1-800-221-8025 (Technical Support) Fax 519-749-3302 (Service) CHRISTIE Digital Systems, Inc. 10550 Camden Drive Cypress, CA 90630 USA Tel.