Projection Engines Cubes Entero RPMSP–LED01 Entero RPMHD–LED01 Entero RPMWU–LED01 CC50 CC67 CC70 CC70HD CC72 Installation Manual 020-100839-01 Entero Projector and Cube Installation Guide 020-100839-01 Rev.
Projection Engines Entero RPMSP–LED01 Entero RPMHD–LED01 Entero RPMWU–LED01 Installation Manual 020-100839-01 Cubes CC50 CC67 CC70 CC72
NOTICES COPYRIGHT AND TRADEMARKS © 2008 – 2013 Christie Digital Systems, Inc.–2012 Christie Digital Systems USA, Inc. All rights reserved. All brand names and product names are trademarks, registered trademarks or trade names of their respective holders. REGULATORY The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Addendum The CD included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product. 手册 中 包 含 的光盘，带有着中文的电子副本，使用或维修本产品前，请仔细查阅 所 有的 指 示 。 Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les instructions avant d'utiliser ou de réparer ce produit. Das CD, das mit diesem gedruckten Handbuch eingeschlossen ist, enthält eine elektronische Kopie auf in deutscher Sprache.
Table of Contents 1: Introduction 1.1 Safety Warnings and Guidelines .................................................................................................1-1 1.2 Contact Support ...........................................................................................................................1-2 2: Cube Installation and Setup 2.1 Christie Pedestals.........................................................................................................................2-1 2.
Table of Contents Calculate Your Hardware Requirement ................................................................................3-14 PHM Network Example: 2 x 3 Wall .....................................................................................3-14 PHM Network Example: 4 x 6 wall ......................................................................................3-15 3.7.3 ArrayLOC Over EM Network .............................................................................................
Table of Contents 5.10 Portions of the Display are Cut Off or Warped to the Opposite Edge ......................................5-5 5.11 Display Appears Compressed (Vertically Stretched) ................................................................5-5 5.12 Data is Cropped from Edges......................................................................................................5-5 5.13 Inconsistent Picture Quality.......................................................................................
1 Introduction This manual provides instructions for installing a display system using Christie Entero RPMSP–LED01, RPMWU–LED01 or RPMHD–LED01 projectors, CC50, CC67, CC70, CC70HD and CC72 display cubes, and PE50, PE67, PE70, PE70HD and PE72 pedestals. The information within this manual is intended for audio visual technicians with experience installing display systems. To avoid personal injury or damage to the projector, read all procedures before starting the installation and observe all precautions.
NOTICES: Failure to comply with the following may result in equipment damage: • Maintain a minimum clearance of 25 mm (1.0”) around the projector for air circulation and a 75 mm (3”) clearance for cable connections to the input panel. Insufficient clearance can cause the projector to overheat during operation and/or place undue stress on source connections. • This projector must be operated in an environment that meets the operating range specification, as listed in Appendix A Specifications. 1.
2 Cube Installation and Setup NOTICE: Only qualified installers should attempt installation of a Christie display wall. NOTE: A clearance of 3 ft or more is recommended behind the display cube for serviceability and installation. 2.1 Christie Pedestals Christie pedestals (models PE50, PE67, PE70, PE70HD, PE72) are recommended when you install Christie display cubes (models CC50, CC67, CC70, CC70HD, CC72). 2.
2.3 Components and Hardware All major components required to assemble a complete display cube are packaged and shipped separately to the installation site. This includes the display cube enclosure, projector, display screen, and pedestal. Each component comes with the hardware required for installation. Check the contents of your shipment against the list below to make sure that you have all the necessary hardware. Hardware is listed by component and applies to all models unless otherwise noted. 2.3.
2.3.4 Entero Projectors Each display wall requires a User Kit (P/N: 125-108100-xx). One User Kit is provided with each order, and 2 are provided with every 4 or more units ordered. • Power Cord • Entero User Kit (P/N:125-108100-xx).
2.4 Unpack Cube Enclosures and Pedestals NOTICES: Failure to comply with the following may result in equipment damage: • Do not cut the protective film off the mirror with a knife. • Do not touch the optical mirror with your bare hands. Fingerprints left on the surface can impact image quality. 1. Lift the cardboard packaging off of the cube enclosures and pedestals. Do not cut the packaging with a knife. 6 CC70 CC50 4 1 5 2 3 1, 3 Cable covers 2 CC50 back panel. Similar for CC72.
2.5 Unpack and Stabilize Screens 1. Wear the lint–free cotton gloves provided in the user kit, remove the screen from the packaging and stand it vertically against a wall or flat surface. Select a low–traffic area away from the installation to protect the screens from accidental scratching or tipping. 2. Let the screen stabilize to ambient site conditions for a minimum 24 hours. 3. Wearing lint-free cotton gloves, remove the protective film from the back of the screen. 2.
2 2 3 3 2 2 4 1 1 1 1 5 1 Use to fasten pedestals together, 4 on each side panel 2 Use to install display cubes, 2 at the back and 2 at the front 3 On PE67/PE70/PE72 pedestals only, use to install display cubes, 2 on support bracket 4 Front Panel (faces the room) 5 Adjustable feet (Qty. 4) 2.6.1 Construct a Multiple Pedestal Platform Before starting, check that you have all the required hardware. See 2.3 Components and Hardware.
5. Tighten the middle nut against the top nut to lock the pedestal foot in position. 6. Check that you can see threads inside the pedestal, at the top of the corner bracket where the foot is installed. If threads are not visible, then you have over–extended the pedestal foot. Readjust the foot before continuing with the installation. 7. Hand-tighten the 2 pedestals together using 4 M6 x 75mm hex screws, 8 flat washers, 4 lock washers, and 4 M6 hex nuts.
2.7 Install Display Cube Enclosures Failure to comply with the following may result in death or serious injury: • Tip Load! The maximum stacking limitation is 5 cubes high in a minimum 2 column display wall. The display wall must be properly anchored anytime the wall is 2 rows or higher to prevent tipping and provide stability. Use all the hardware provided to fasten the display cubes to the support structure. See 2.8 Install Permanent External Support, on page 2-11.
1. If space behind the display wall is limited, it is recommended the long-screen bolts are inserted into the back of the cubes before the cubes are installed. 2. Install the first row of cube enclosures starting from the center and working outwards. a. From the back of the display structure, lift the cube enclosure over the pedestal or cube row and lower it in the center of the pedestal or cube. A crew of 2 or more can lift a display cube into position on the first row. b.
3. Loosen each of the adjustment screws on the optical mirror to minimize tension against the mirror at each adjustment point. 4. Check the alignment between all of the display cubes and make adjustments as required. All cubes must be aligned vertically and horizontally. 5. Tighten all mounting hardware between the display cubes and pedestals before installing another row of display cubes. Tighten hardware to a maximum torque setting of 11.1 Nm / 98 lbf.-in. 6.
2.8 Install Permanent External Support Tip Load! The maximum stacking limitation is 5 cubes high in a minimum 2 column display wall. The display wall must be properly anchored anytime the wall is 2 rows or higher to prevent tipping and provide stability. Use all the hardware provided to fasten the display cubes to the support structure. When stacking display cubes, they must be installed on a level surface.
2.8.2 Lag Bolt Application Each column of cubes requires 4 lag bolts. Each lag bolt must be capable of withstanding a pull out force of 500 lbs. DANGER! The amount of external support required is dependent on the size of the display wall. Support structures must be designed and implemented by a qualified installer and comply to local area safety standards. Failure to comply results in death or serious injury. 2-12 Entero Projector and Cube Installation Manual 020-100839-01 Rev.
2.9 Install Screens NOTICE: Failure to comply with the following may result in equipment damage: • Read this entire section before installing the screens. • Wear the lint-free gloves provided in the user kit when handling the screens to prevent leaving fingerprints on the surface. • Start with the center cube of the first row and work outwards. • Check that you have all the required hardware. See 2.3 Components and Hardware. 1.
b. For vertical adjustment: Insert 2 M8 vertical alignment screws at each end of the screen, from the inside of the frame so that they are flush with the inside surface of the screen frame. Turn a screw clockwise to increase the height on that side of the screen. Use vertical adjustments to equalize the seams between the cubes. Screen adjustment screws short– screen bolts (for top row only) From inside screen, raise or lower screen adjustment screws to adjust screen gap 0.
3 Projector Installation and Setup The projector is designed for installation in a Christie cube display or a custom display structure. Before installing projectors, make sure that the screens have been installed and that screen depth and height adjustments are complete. For information about installing an Entero projector in a custom installation, see 3.5 Installing the Projector in a Custom Structure. Use a stable cart to transport the projector.
3.3 Projector Components 3 4 2 1 1 6–axis Adjuster 2 Projection Head Module (PHM) 3 Electronics Module (EM) 4 Light Module (LM) 3.3.1 Projection Head Module (PHM) The PHM contains the projection lens, infrared sensor, digital micromirror device (DMD), light module, and other optical components. The module includes the electrical connections that are used to drive these components. 3.3.2 Light Module (LM) The LM consists of 3 LEDs and associated optics. 3.3.
3.4 Install Projectors into Cube Enclosures The PHM and adjuster plate are shipped installed on the 6–axis adjuster. 3.4.1 Tools and Hardware Required • • • • • • • • M6 Cap screws (Qty. 8) M5 Cap screws (Qty. 5) M6 flat washers (Qty. 8) M3 Phillips™ screwdriver (Qty. 2) Cable ties (Qty. 5) Cable anchor M5 hex key M4 hex key CC50 Others 2 2 1 1 1 Location for 2 front M6 cap screws and washers, viewed from the front. 2 Slotted mounts on the 6–axis adjuster, viewed from the front. 1.
5. Install the remaining 2 M6 cap screws and M6 flat washers. Tighten all 4 screws. only front screws shown 6. Remove the 4 shipping bolts from the adjuster. Remove Tape and Loosen Securing Bolt Before Operation Remove Tape and Loosen Securing Bolt Before Operation shipping bolts 7. Turn the EM so the bracket extension faces the back of the cube. 8. Install the EM to the left of the projector using the 3 M6 cap screws and 3 flat washers. The EM mounting location is determined by the cube model.
3.5 Installing the Projector in a Custom Structure When installing in a custom structure, refer to the design and installation instructions for the custom structure. Projector position and orientation should be part of the installation design. To review Christie–provided information about the projector such as measurements, clearance requirements, and throw distance calculation, download the CAD drawing for the projector. Visit www.christiedigital.
5. Turn the adjuster 180°. 6. Align the holes on the mounting plate with the 4 holes on the adjuster, as shown. 180° 7. Secure with 4 mounting screws removed in step 4. 8. Unscrew the guide pins and re–install them in the mounting plate in the holes marked Pin H. 3-6 Entero Projector and Cube Installation Manual 020-100839-01 Rev.
9. Loosely install 2 M6 cap screws (removed in step 1) onto the back of the projector, as shown. 10. Position the projector with the guide holes over the guide pins and the loosely install the screws over the slots in the flange. 11. Settle the projector on the guide pins and secure to the flange with M5 screws installed in step 9. 3.6 Wiring 3.6.1 Tips for Running External Cables to Projectors All Christie cubes have cable channels in standard locations.
3.6.2 Connect the PHM to the EM and AC 1. Install the projector cables. To determine the location of each cable, see the Interconnection Diagram affixed to the LM. 2. Move the cables connecting the projector to the EM away from the projector vents and the light path, and secure with cable ties. Interconnection Diagram Electronics Module EM Power Link A EM Network Projection Head Module Link A EM Network Light Module 9 3. Attach a cable anchor to the cube frame with an M6 cap screw and a flat washer.
3.6.3 Connect Projectors for External Communication By default, communications originating from one type of serial controller (RS232, RS422, or Ethernet) stay on the corresponding network path. A Configuration > Communications > Network Routing > Separate setting indicates this separation. For example, when using an RS422 controller, it will communicate only with the projector to which it is connected, unless the setting is changed to RS232 and RS422 Joined or All Joined.
Mixed Network In the illustrated mixed network, the controller can communicate with the first projector and the command can be relayed to each serially connected projector. This configuration is useful if you are using a non–RS232 controller with the RS232 linking available between these projectors. The example shows both an RS422–compatible controller and an Ethernet–connected PC for working with a network of projectors linked using their RS232 IN/ OUT ports. CAT5 et ern Eth ub H CAT5 1.
RS232 Network In the illustrated RS232 network, the controller can communicate with the first projector and the command can be relayed to each serially connected projector. NOTICE: Using the wrong type of serial cable can damage the projector. 1. Connect the controller to one projector using a serial cable between the PC and the RS232 IN port on the electronics module. 2.
Mixed Serial Network (RS232 and RS422) RS422 serial communication is better over long distances than RS232 communication. Use the RS422 port only if your device has the capability. Always read the equipment literature before connecting. NOTICE: Connecting to the RS422 port with incompatible equipment, including the wrong type of serial cable, can damage the projector.
3.7 Connect Projectors for ArrayLOC Christie Entero projectors use Christie ArrayLOC technology to automatically and continuously synchronize color and brightness settings across all projectors in an array. 3.7.1 Hardware Requirements One or more external Ethernet switches are required to create a private ArrayLOC network. To make sure the network operates effectively, do not connect the ArrayLOC network to other external or internal networks.
3.7.2 ArrayLOC Over PHM Network In a PHM Network for ArrayLOC, only the PHM of each projector is connected to the network switch. The projector EM remains connected to the PHM. Calculate Your Hardware Requirement In an PHM Network for ArrayLOC, each projector requires 1 port on a network switch. For example, if you install a 2 x 4 cube wall with 8 projectors, 8 ports are required (8 x 1 = 8). If you use multiple switches, they must be connected to one another to form a single network.
PHM Network Example: 4 x 6 wall This illustration shows a 4 x 6 ArrayLOC configuration with three 10–port network switches. EM EM PHM PHM EM EM PHM PHM EM EM Switch PHM PHM EM EM PHM PHM EM EM Switch PHM PHM EM EM PHM PHM Switch EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM EM PHM 3.7.3 ArrayLOC Over EM Network In an EM Network for ArrayLOC, the projector EM and PHM are connected to a network switch.
Calculate Hardware Requirements In an EM Network for ArrayLOC, each projector requires 2 ports on a network switch. For example, if you install a 2 x 4 cube wall with 8 projectors, 16 ports are required (8 x 2 = 16). Multiple switches must be connected to one another to form a single network. Typically, 2 extra ports are required on each switch when you install multiple switches. For example, 22 ports are required if you install 3 switches for a 2 x 4 cube wall with 8 projectors (8 x 2 = 16) + (2 x 3 = 6).
EM Network Example: 4 x 6 Wall To reduce the length of the Ethernet cabling for larger installations, use multiple, smaller switches instead of a single, large switch. This illustration shows an ArrayLOC configuration with 6 10–port network switches.
3.7.4 Enable ArrayLOC If using projector software version 1.3.x or later, the type of ArrayLOC network configuration being used must be specified. 1. Navigate to the Main Menu > Configuration > ArrayLOC > ArrayLOC Configuration > ArrayLOC Network option. 2. Select an ArrayLOC Network type in the list. IMPORTANT: For the ArrayLOC functionality to work correctly, each projector in the array must be configured to use the sam ArrayLOC network configuration. 3.
3.8.2 Dual Link DVI Input Card This card accepts a single DVI signal over a DVI–I connector and analog video signals over the DVI–I or 15–pin VGA connector. The module can simultaneously support a digital signal on the DVI input and an analog signal on the VGA port; however, it does not support 2 analog signals at the same time. There are 4 LEDs on the module faceplate.
3.8.4 Analog BNC Input Card This card accepts several types of Sync modes. In 5–wire Sync mode, all 5 BNC connectors are used. If H/C and V connectors are swapped, this card will still operate normally. An analog graphic source, such as a VGA from a PC, can be connected. The card can operate in 4–wire Sync mode, which accommodates 4–wire RGBC sources. The composite Sync cable can be connected to either the H/C BNC or the V BNC.
3.8.6 Video Decoder Input Card This card accepts and decodes SD video. This includes CVBS (composite video), S–Video, and component sources. This card supports as many as 6 video signals, 4 of them on BNC connectors and 2 on 4–pin mini–DIN connectors. Each mini–DIN connector accepts one S–Video signal.
3.9 System Integration – GPIO Connector The General Purpose Input Output (GPIO) connector located on the input panel provides a flexible method of interfacing external I/O devices to the projector. There are 7 GIO pins on the 9–pin D–Sub GPIO connector, which are configured via RS232 commands. The other 2 pins are reserved for ground, and power.
4 Adjust the Image If necessary, make the adjustments outlined in this section for each display. Obtain the best results possible before moving on to the next adjustment. Image adjustments include: • • • • 4.1 6–axis adjustment: Adjusts image geometry to best match the screen perimeter. Lens focus adjustment: Adjust for best image focus on the screen. Mirror adjustment (only if required): Adjusts fine geometry around the perimeter of the screen.
4.3 Focus .64:1 Fixed Lens The focus and geometry for Entero projectors are preset for installation in CC67 cubes. For all other installations, follow the steps outlined below. 1. Press Test once on the remote to display the internal geometry test pattern. The test image should approximately fill the screen. If not, make a course adjustment using the 6–axis adjuster (see 4.4 Adjust Image Geometry Using the 6–axis Adjuster). 2.
4.4 Adjust Image Geometry Using the 6–axis Adjuster Use the adjuster controls to adjust image geometry: position, keystone, zoom and tilt. Adjustment knobs are color-coded. The 6–axis adjustment label on the product illustrates the function of each. Before making adjustments, make sure the lock screws for each adjustment knob are loosened. Use the 5 mm hex key provided to loosen the M6 lock screws and a 2 mm hex key (not provided) to loosen the collar lock screws.
NOTES: 1) If it is necessary to make mirror adjustments do so only after you have completed this procedure. 2) Start with the displays in the center of the bottom row and work towards the end of the row. 1. Work from the back of the display cube. Make sure you can see all 4 sides of the image on the inside of the screen. 2. Adjust the lens for best image focus on the screen. See 4.5 Fine–tune Image Geometry using the Mirror, on page 4-5. 3.
4.5 Fine–tune Image Geometry using the Mirror NOTICE: Do not use tools to tighten the thumbscrews on the mirror to prevent the possibility of it cracking. NOTE: Adjust the optical mirror only when image geometry cannot be corrected with the 6–axis adjuster. This section outlines how to fine adjust the image geometry using the mirror adjustments. For example when the edges of a single corner do not properly line up to the screen, or when a side of the image bows in or out slightly.
4.5.1 Mirror Adjustment Screws Turn screws clockwise to pull the mirror away from the screen and make the image larger in the corresponding area. NOTE: Turning the D1 adjustment screw clockwise pushes the mirror towards the screen. Turn screws counter–clockwise to push the mirror towards the screen and make the image smaller in the corresponding area. NOTE: Turning the D1 adjustment screw counter– clockwise pulls the mirror away from the screen.
4.5.3 Image Geometry Troubleshooting using the Mirror The following examples illustrate what areas of the optical mirror to adjust to achieve the desired image.
Image Problem Screws to Adjust Direction of Movement by Mirror During Adjustment A1 Image Problem C1 Screws to Adjust C2 A1 B1 B2 D1 Turn thumbscrews clockwise in zones C1– C2 to pull the mirror A1 C1 B1 C2 B2 D1 Turn thumbscrews clockwise in zones C and D, and counter–clockwise in D1 to pull the mirror A1 C1 B1 C2 B2 D1 Turn thumbscrews counter–clockwise in zones A–A1–B to push the mirror.
4.5.4 Barrel and Pincushion Distortion To correct barrel or pincushion distortion, adjust the A1 and B1, B2, C1, C2, and D1 mirror screws. Barrel Distortion 4.6 Pincushion Optimize Image Setup and Display 4.6.1 Initialization and Auto Setup NOTE: To adjust image position, size/zoom, tilt, or keystone in a display wall system, see 4.4 Adjust Image Geometry Using the 6–axis Adjuster, on page 4-3. Software adjustments to image geometry in a display wall are rarely used. 1.
For information about managing channels, see the Entero RPMWU/RPMSP/RPMHD–LED01 User Manual (P/N: 020-100367-xx). 4.6.2 Adjust Image Geometry Using the Projector Software Only use projector software options if the images still requires adjusting after the hardware has been optimized and Auto Setup has been run. See the Entero RPMWU–RPMSP–RPMHD–LED01 User Manual (P/N: 020100367-xx) for details about software based geometry changes: Size and Position, Resize Presets, Geometry Correction. 4.6.
• You may have to add some red to some of the blues. e. Use the white color settings to achieve a uniform white across all projectors. f. Exit the color adjustment menus. Once you have completed these adjustments, the ArrayLOC feature automatically monitors and maintains the color and brightness uniformity across the display wall. 4.
5 Troubleshooting NOTICE: To avoid personal injury or damage to the projector read, understand, and observe all warnings and precautions before servicing the projector. This section provides information and procedures for resolving common display issues. If you cannot resolve a display issue, contact your dealer. Only Christie accredited service technicians are authorized to service this product. When diagnosing an issue: • Make sure that the system is plugged in.
5.2 Error Codes If the status display window shows one of the codes in the Error Codes table you may need a Christie accredited service technician to repair the component identified by the error code. Error codes are displayed in a 3–phase format: • First 2 digits represent the component or error category • Second 2 digits represent the specific problem • Display off This cycle repeats. The LED will be red while the error code is displayed.
SP 06 LM Air inlet overtemp or sensor not functioning SP 07 LM C Air exhaust overtemp or sensor not functioning SP 08 LM LED Driver overtemp or sensor not functioning SP 09 LM Power supply overtemp or sensor not functioning SP 10 LM ambient overtemp or sensor not functioning SP 11 LM Red thermistor overtemp or sensor not functioning SP 12 LM Green thermistor overtemp or sensor not functioning SP 13 LM Blue thermistor overtemp or sensor not functioning SP 14 LM IR thermistor overtem
5.4 Projector Does Not Turn On • Make sure the projector is plugged in. • Make sure cables are connected and not damaged. 5.5 Light Module Suddenly Goes Off 1. Check shutter setting – if status display shows SH then the shutter may be active. Toggle through shutter modes. In gray shutter mode it should be possible to display menus. 2. Verify RGB Brightness is set sufficiently higher than zero to ensure a visible image.The DMDs may be overheated. Check for an alarm condition. 5.
5.9 The Upper Portion of the Display is Waving, Tearing or Jittering 1. Check that the RGB Brightness setting is not too low. 2. Check the signal level on the input device. 5.10 Portions of the Display are Cut Off or Warped to the Opposite Edge If you have resized the image, adjust the resizing settings until the entire image is visible and centered. 5.11 Display Appears Compressed (Vertically Stretched) 1. Adjust the frequency of the pixel sampling clock for the input source. 2.
5.17 Display is Noisy 1. Adjust the input source pixel tracking, phase, and filter. 2. Verify the video input is terminated (75 ohms). If the device is the last device in a linked series, verify the video input is terminated at the last input source. 3. Verify the cables connecting the input device to the projector meet the minimum requirements. 4. Add signal amplification or conditioning if the distance between the input device and the projector exceeds 25 ft (7.6 m).
6 Maintenance The following procedures are provided for use as needed. There is no required set maintenance schedule for this product. 6.1 Ventilation The operating environment in which you operate the display cubes should not exceed the temperatures defined in Appendix A Specifications. Make sure there is adequate airflow around the display cubes. 6.2 Clean the Mirror NOTICE: Typically, it is not necessary to clean the mirror; however, if required do not use ammoniated window cleaner.
Remove Finger Prints 1. Use a lint free cotton cloth with acetone and alcohol to dab the stain. For a finger print that is hard to remove, use a cotton swab dipped in acetone. 2. 6.3 Use compressed air to dry the solvent. Clean the Screen Notice: Typically, it is not necessary to clean the screen; however, if required follow the guidelines listed here. 6.3.
6.4 Clean the Projection Lens NOTICE: Clean only if necessary. A small amount of dust on the lens has little effect on picture quality. 6.4.1 Items Required • Camel–hair brush • Lint free cloths (without color) • Coated optics cleaning solution 6.4.2 Instructions Remove Dust 1. Brush most of the dust from the lens with a camel-hair brush or blow dust away with a dust-free blower. 2. Fold a microfibre cloth smooth and gently wipe remaining dust particles from the lens.
A Specifications This appendix includes specifications and brief dimension drawings for the following display units: • • • • • CC50 CC67 CC70 CC70HD CC72 Additional information and drawings are available for download from www.christiedigital.com. Entero Projector and Cube Installation Manual 020-100839-01 Rev.
A.
A.1.1 CC50 Brightness and Performance Characteristics Engine option Screen option Screen type Viewability Horiz. SXGA+ Horiz. Verti. Brightness (cd/m 2 ) A RPMSP-LED01 t SC50-LE02 t Lenticular t 160° t 60° t ±40° t ±10° t 913 RPMSP-LED01 t SC50-XP01 t Cross prism t 180° t 120° t ±35° t ±27° t 470 B 1 Screen 1/2 gain Verti. 1 Brightness specifications are at reduced color space settings. Entero Projector and Cube Installation Manual 020-100839-01 Rev.
A.2 CC67 Specifications SXGA+ cube t CC67-3001 projection engine t RPMSP-LED01 screen options t SC67-XP01 imaging t 1-chip DLP, Dark Chip native resolution t SXGA+ (1400 x 1050) illumination t Light Emitting Diodes (Red, Green, Blue) Pixel density pitch t 26.
A.2.1 CC67 Brightness and Performance Characteristics Engine option Screen option Screen type Viewability Horiz. SXGA+ 1 RPMSP-LED01 t SC67-XP01 t Cross prism t 180° Screen 1/2 gain Verti. t 120° Horiz. t ±35° Verti. t ±27° Brightness (cd/m 2 ) t 1 260 Brightness specifications are at reduced color space settings. Entero Projector and Cube Installation Manual 020-100839-01 Rev.
A.
A.3.1 CC70 Brightness and Performance Characteristics Engine option Screen option Screen type RPMHD-LED01 t SC70-XP01 t Viewability Horiz. HD native 1 Cross prism t 180° Screen 1/2 gain Verti. t 120° Horiz. t ±35° Verti. t ±27° Brightness (cd/m 2 ) t 1 216 Brightness specifications are at reduced color space settings. Entero Projector and Cube Installation Manual 020-100839-01 Rev.
A.
A.4.1 CC72 Brightness and Performance Characteristics Engine option WUXGA 1 RPMWU-LED01 Screen option t SC72-XP01 Screen type t $rPTT QSJTN Viewability Screen 1/2 gain Horiz. Verti. Horiz. Verti. t ¡ t ¡ t ¡ t ¡ Brightness (cd/m 2 ) 1 t #SJHIUOFTT TQFDJmDBUJPOT BrF BU rFEVDFE DPMPS TQBDF TFUUJOHT Entero Projector and Cube Installation Manual 020-100839-01 Rev.
*000-103704-01* ASSY TECH DOCS Entero Projector and Cube Install
*000-103704-01* ASSY TECH DOCS Entero Projector and Cube Install Corporate offices Worldwide offices USA – Cypress ph: 714-236-8610 United Kingdom ph: +44 118 977 8000 Eastern Europe ph: +36 (0) 1 47 48 100 Singapore ph: +65 6877-8737 Japan ph: 81-3-3599-7481 Canada – Kitchener ph: 519-744-8005 France ph: +33 (0) 1 41 21 00 36 Middle East ph: +971 (0) 4 299 7575 Beijing ph: +86 10 6561 0240 South Korea ph: +82 2 702 1601 Germany ph: +49 2161 664540 Spain ph: + 34 91 633 9990 Shanghai ph: +86
