Installation manual

ManualsBrandsChristie ManualsProjectorCC50

Table of Contents

LIT MAN INSTALL Cube i

013-100526-01 Rev. 1 (04/07)

Introduction ......................................................................................................................1-1

How to Use This Manual ...............................................................................................................1-2

Typographical Conventions ..............................................................................................................................1-2

Illustrations ......................................................................................................................................................1-3

Christie Contact Information ........................................................................................................1-3

Safety Warnings and Guidelines ..................................................................................................1-3

Stacking Limitations .........................................................................................................................................1-4

Using Christie PE50/PE67 Pedestals ..................................................................................................................1-4

External Support ..............................................................................................................................................1-4

Hardware .........................................................................................................................................................1-4

Lifting DiSplay Cubes .......................................................................................................................................1-5

Airflow Considerations .....................................................................................................................................1-5

Installation & Setup ..........................................................................................................2-1

Components ...................................................................................................................................2-2

Tools Required .................................................................................................................................................2-3

Service and Support .........................................................................................................................................2-3

Installation .....................................................................................................................................2-3

Step 1 - Unpacking Cube Enclosures and Pedestals ..........................................................................................2-3

Step 2 - Unpack and Stabalize Screens .............................................................................................................2-4

Step 3 - Unpack and Prepare Projectors for Installation .....................................................................................2-5

Step 4 - Assemble the Pedestals .......................................................................................................................2-6

Step 5 - Install Display Cube Enclosures ............................................................................................................2-8

Step 6 - Apply Permanent External Support ....................................................................................................2-12

Step 7 - Install Display Screens .......................................................................................................................2-13

Step 8 - Install Projectors into Cube Enclosures ...............................................................................................2-16

Step 9 - Connect Sources ...............................................................................................................................2-16

Step 10 - Power Projectors ON .......................................................................................................................2-17

Step 11 - Mechanical Setup: Adjust Image Geometry and Focus .....................................................................2-17

Step 12 - Software Setup: Optomize Image Setup and Display .......................................................................2-23

Appendix ..........................................................................................................................A-1

Summary of content (36 pages)

PAGE 1
Table of Contents Introduction ......................................................................................................................1-1 How to Use This Manual ............................................................................................................... 1-2 Typographical Conventions .............................................................................................................................. 1-2 Illustrations ................................................
PAGE 2
PAGE 3
1 Introduction This installation manual contains important information for the safe and successful installation of a Christie CC50-3301 (CC50) or CC67-3801 (CC67) display cube system, whether as a single unit system or as a multiple unit system. Additional important information relating to the CC50/CC67 display cube system can be found in the RPMX/RPMSP-D120U User’s Manual. The installer should be familiar with all such information prior to commencing installation.
PAGE 4
Section 1: Introduction CAUTION Installation of a display wall should be undertaken only by qualified installers having the requisite training, knowlege, skill and experience to properly install the system. PLEASE READ THIS INSTALLATION MANUAL CAREFULLY AND IN ITS ENTIRETY PRIOR TO COMMENCING INSTALLATION. 1.1 HOW TO USE THIS MANUAL This installation manual is intended to provide qualified installers with specific step-by-step installation information, from unpacking to advanced image setup.
PAGE 5
Section 1: Introduction DANGER THE LIGHTNING FLASH AND ARROWHEAD SYMBOL WITHIN THE EQUILATERAL TRIANGLE ALERTS THE USER TO UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PROJECTOR'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK THAT WILL LEAD TO SEVERE BODILY HARM, OR DEATH.
PAGE 6
Section 1: Introduction 1.3.1 STACKING LIMITATIONS There are specific stacking limitations for each display cube product. Do not stack display cubes higher than the specified stacking limits when using the approved PE50/PE67 pedestal. (See Table 1.1 below.) Stacking display cubes higher than what is recommended increases the possibility of the display wall becoming unstable and unsafe and also increases the chance that the pedestals may buckle from the extra weight. Table 1.
PAGE 7
Section 1: Introduction 1.3.5 LIFTING DISPLAY CUBES A crew of two or more can lift a display cube into position on the first row. DANGER LIFT EQUIPMENT MUST BE USED TO LIFT DISPLAY CUBES INTO POSITION ON HIGHER ROWS. 1.3.6 AIRFLOW CONSIDERATIONS It is important that the room temperature measured all around the display wall is no greater than the operating temperature stated in the product specifications.
PAGE 8
Section 1: Introduction 1-6 LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 9
2 Installation & Setup This section provides information on assembling CC50/CC67 components as a stand-alone unit or as a multi-unit display wall. In this section: • 2.1 Components • 2.1.1 Tools Required • 2.1.2 Service and Support • 2.2 Installation • 2.2.1 Step 1 - Unpacking Cube Enclosures and Pedestals • 2.2.2 Step 2 - Unpack and Stabalize Screens • 2.2.3 Step 3 - Unpack and Prepare Projectors for Installation • 2.2.4 Step 4 - Assemble the Pedestals • 2.2.
PAGE 10
Section 2: Installation & Setup 2.1 COMPONENTS All major components required to assemble a complete display cube are carefully packaged and shipped separately to the installation site. This includes the display cube enclosure, projector and the display screen. Each component comes with enough hardware for installation. PE50/PE67 pedestals are also carefully packaged and shipped fully assembled with hardware.
PAGE 11
Section 2: Installation & Setup In addition to the contents of the display cube enclosure, each display system is provided with a User’s Kit* which includes the following components: RPMX/RPMSP-D120U User’s Manual CC50/CC67 Installation Manual IR remote keypad with 2AA batteries Assorted ball drivers A pair of lint free cotton gloves (required for screen handling) *Additional User’s Kits can be purchased separately by referencing the Christie part number (102138101-01) when ordering.
PAGE 12
Section 2: Installation & Setup FIGURE 2-1 REMOVING THE REAR ACCESS COVER 3. Remove the packaging material used to protect the optical mirror. Make sure not to bump or scratch the mirror while doing this. Also, do not touch the optical mirror with your bare hands. NOTE: Fingerprints left on the surface can impact the quality of a displayed image. 4.
PAGE 13
Section 2: Installation & Setup 2.2.3 STEP 3 - UNPACK AND PREPARE PROJECTORS FOR INSTALLATION The projector is shipped fully assembled in a lens-vertical configuration. To prepare it for installation, complete the following: 1. Remove all packaging surrounding the projector. NOTES: 1) It is recommended that complete packaging for at least one projector be kept on-hand in the unlikely event that a project needs to be returned to the factory for servicing or replacement.
PAGE 14
Section 2: Installation & Setup 2.2.4 STEP 4 - ASSEMBLE THE PEDESTALS It is strongly recommended that PE50/PE67 pedestals (Figure 2-4) are used in creating the platform for a CC50/CC67 display wall. These pedestals are designed specifically to support the CC50/CC67 cube enclosures to their maximum stacking limit. Before you begin assembly of the pedestal (Figure 2-5), ensure you have the correct pedestal model for your display cube.
PAGE 15
Section 2: Installation & Setup When constructing a PE50/PE67 platform (multiple pedestals), complete the following: Refer to Figure 2-6 (panel #3) for correct screw location. 1. Slide two pedestals together aligning front and rear edges until flush. 2. Using a level, determine which side(s) of the pedestal require adjustment. Then as required, adjust the pedestal feet until the two pedestals are level on all sides and with each other.
PAGE 16
Section 2: Installation & Setup 2.2.5 STEP 5 - INSTALL DISPLAY CUBE ENCLOSURES Refer to Figure 2-7 and Figure 2-8.
PAGE 17
Section 2: Installation & Setup FIGURE 2-8 CUBE ENCLOSURE MOUNTING LOCATIONS Add the FIRST ROW of display cube enclosures Refer to Figure 2-9. 1. There are 17 3-mm hex-cap screws on the outer edge of mirror frame used to secure the optical mirror for transport. Slightly loosen each of these screws (approximately 1/4 turn) to relax the optical mirror. NOTICE: This should be done before the screen is installed (Section 2.2.
PAGE 18
Section 2: Installation & Setup f. Check alignment between all display cubes, and since the hardware is relatively loose make small adjustments as required. g. Tighten all hardware between display cubes and pedestals before adding on the next row of display cubes. Some adjustment of the pedestal feet may be required to achieve a level row. FIGURE 2-9 INSTALL FIRST ROW OF DISPLAY CUBE ENCLOSURES Adding ADDITIONAL ROWS of display cube enclosures Refer to Figure 2-10. 1.
PAGE 19
Section 2: Installation & Setup h. Tighten all hardware between top and bottom display cubes before adding on the next row of display cubes. i. Continue adding ADDITIONAL ROWS until all display cubes are installed. j. Install Christie Nameplate (component in User Kit) in the top-right corner of the far right pedestal as shown in Figure 2-11. FIGURE 2-10 ADDING ADDITIONAL ROWS OF DISPLAY CUBE ENCLOSURES FIGURE 2-11 INSTALL CHRISTIE NAMEPLATE LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 20
Section 2: Installation & Setup 2.2.6 STEP 6 - APPLY PERMANENT EXTERNAL SUPPORT A CC50/CC67 display wall requires some method of external support regardless of its overall height. The method and frequency of external support must be determined by a qualified installer. Reinforcing the structure will prevent the wall from tipping due to unforseen circumstances, such as earthquakes etc. WARNING 1) EXTERNAL SUPPORT FOR A DISPLAY WALL MUST BE DESIGNED AND IMPLEMENTED BY A QUALIFIED INSTALLER.
PAGE 21
Section 2: Installation & Setup 2.2.7 STEP 7 - INSTALL DISPLAY SCREENS Tools/hardware required: For each CC50 screen, 4-M6 x 737 mm screen bolts For each CC67 screen, 4-M6 x 852 mm screen bolts For top row only, use two of the short screen bolts with 2-M6 x 50 mm screws for each screen Torque wrench TIPS: Extend the two screen support set screws before installing a screen. This will ensure the weight of the screen is transfered to the pedestal/display cube below.
PAGE 22
Section 2: Installation & Setup 4. Working outward from the centre cube, repeat 1 - 3 above for the next screen. Ensure that there is a 0.5 mm gap between each screen. 5. Continue the process of adding screens, one at a time until all screens are added on the first row. Check along the way that screens are level and the gap is even between them (approximately 0.5mm). 6. Temporarily hand-tighten screen hardware until next row is installed. 7.
PAGE 23
Section 2: Installation & Setup FIGURE 2-15 FULLY EXTEND SCREEN ADJUSTMENT SCREWS FOR SUPPORT FIGURE 2-16 INSTALLING SCREENS ON SECOND ROW OR HIGHER LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 24
Section 2: Installation & Setup 2.2.8 STEP 8 - INSTALL PROJECTORS INTO CUBE ENCLOSURES Tools required: The four positioning tubes shipped with the projector. These are used to nominally position the projector within the cube enclosure To properly install the projector into a cube enclosure, complete the following (Refer to Figure 2-17): NOTICE: Keep the lens cap on the projector during installation to prevent damaging the lens. 1. Remove the knurled thumb-nut from each post inside the cube enclosure.
PAGE 25
Section 2: Installation & Setup 2.2.10 STEP 10 - POWER PROJECTORS ON Each projector is supplied with a North American rated line cord. Make sure you use an appropriately rated line cord for your area before connecting the projectors to AC. Refer to the RPMX/RPMSPD120U User’s Manual for projector power requirements and other Specifications. 1. Plug one end of the line cord to the AC receptacle on the projector, which is located on the electronics module.
PAGE 26
Section 2: Installation & Setup To adjust a display for image geometry, complete the following: 1. Ensure that the series of 3-mm hex-cap screws on the edge of the optical mirror frame have been loosened (approximately 1/4 turn) to relax the optical mirror. NOTE: See section 2.2.5 Step 5 Install Display Cube Enclosures. 2. Prepare the screen for mechanical adjustment, by completing the following steps: a. Display an internal Test Pattern on each screen.
PAGE 27
Section 2: Installation & Setup If the adjuster’s vertical adjustment becomes difficult, try reducing the tilt settings (make flat) to see if you can gain any vertical movement. Keep height adjustments within 1mm of each other to reduce substantial differences in tilt. Refer to the illustration below as you adjust the 6-axis adjuster in the following manner: a. b. c. d. e. f. Center the image on screen, by adjusting vertical and/or horizontal position.
PAGE 28
Section 2: Installation & Setup displayed within a corresponding zone of the screen (Figure 2-19). In some cases, more than one screw will require adjustment. Read through the following tips and review the examples provided. There is no steadfast way in which the mirror is adjusted. In general, fix the corners of the image first, then the edges if required. Just keep in mind, this is a fine adjustment of the image only.
PAGE 29
Section 2: Installation & Setup FIGURE 2-19 CORRESPONDING SCREEN ZONES AFFECTED BY OPTICAL MIRROR ADJUSTMENT Adjusting brass screws: When adjusting any corner of an image, whether to enlarge or make smaller, adjust one of the four brass screws first. These screws are located on a separate brackets near each corner of the mirror. See Figure 2-20.
PAGE 30
Section 2: Installation & Setup 2-22 LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 31
Section 2: Installation & Setup 2.2.12 STEP 12 - SOFTWARE SETUP: OPTOMIZE IMAGE SETUP AND DISPLAY Use the instructions in the following step to optimize the settings of the projector to display the brightest and sharpest image possible. Adjust each display separately, then “tweak” your settings between all displays until you achieve the ultimate display. This is an outline only, refer to the RPMX/ RPMSP-D120U User’s Manual for detailed instructions on how to adjust the various settings. 1.
PAGE 32
Section 2: Installation & Setup 11. From Size and Position, adjust Size until the image is at the desired width and height. You may have to adjust H-Position and V-Position again to re-center the image after adjusting these settings. Continue this step until the image is centered on screen. 12. Adjust Color Wheel Delay. 13. Perform Color Temperature setup. 14. Adjust blacklevels and input levels. 15. Adjust lamp power to match lamp brightness of adjacent displays, if needed.
PAGE 33
A LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 34
APPENDIX A-2 LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 35
APPENDIX LIT MAN INSTAL Cube 013-100526-01 Rev.
PAGE 36
APPENDIX A-4 LIT MAN INSTAL Cube 013-100526-01 Rev.