Chord Electronics Product Communication | English The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB. Great Britain. +44 (0) 1622 721 444 info@chordelectronics.co.uk chordelectronics.co.uk ULTIMA PRE 2 Manual - V.1.
Chord Electronics ULTIMA PRE 2 | Manual _ Contents 0.0 1.0 Safety instructions 03 2.0 Warranty 08 1.1 1.2 1.3 1.4 04 05 06 2.1 2.2 09 Introduction Protection against liquids & heat Dismantling & Radio frequency interference Connecting your equipment 3.0 Getting to know ULTIMA PRE 2 3.1 3.2 3.3 3.4 3.5 Getting to know ULTIMA PRE 2 The front panel The top panel The rear panel The remote control 5.0 How to navigate the menu 5.1 5.2 5.3 5.4 5.
Chord Electronics ULTIMA PRE 2 | Manual _ Safety instructions 1.0 3 // 33 1.0 1.1 Introduction 1.2 Protection against liquids & heat 1.3 Dismantling & Radio Frequency interference 1.
1.1 1.2 Chord Electronics ULTIMA PRE 2 | Manual _ Introduction ULTIMA PRE 2 is flexable pre-amplifer featuring eight inputs, four stereo pairs of XLRs for balanced connections and another four RCA for unbalanced connections and a single stereo pair is available via XLR or RCA for outputs. Before operation, we strongly advise you read this user manual thoroughly.
1.1 1.2 Chord Electronics ULTIMA PRE 2 | Manual _ Protection against liquids & heat ULTIMA PRE 2 is not protected against liquids of any kind. Never place containers of liquid on ULTIMA PRE 2. Never allow ULTIMA PRE 2 to come into contact with moisture or liquids; doing so could result in electrocution or damage to the ULTIMA PRE 2’s internal circuitry.
1.1 1.2 Chord Electronics ULTIMA PRE 2 | Manual _ Dismantling & radio frequency interference There are no userserviceable components within the ULTIMA PRE 2 or its power supply. Dangerous voltages/currents exist within the ULTIMA PRE 2 and its power supply, posing a severe risk of electrocution and/or fire. Never attempt to open, dismantle or apply internal thirdparty devices to it or insert anything other than the listed interconnects or headphone adapters within this user manual.
1.1 1.2 Chord Electronics ULTIMA PRE 2| Manual _ Connecting your equipment Before connecting the ULTIMA PRE 2 to any equipment, consult the manufacturer’s user guide to confirm compatibility. When connecting the ULTIMA PRE 2 to any equipment, make sure that all devices are off, including the ULTIMA PRE 2. Once connected, switch all equipment on starting with the source and ending with the amplification.
Chord Electronics ULTIMA PRE 2 | Manual _ Warranty 2.0 8 // 33 2.0 2.1 Warranty period & registering your purchase 2.
2.1 Chord Electronics ULTIMA PRE 2 | Manual _ Warranty period & registering your purchase At point of sale, Chord Electronics Ltd. provides ULTIMA PRE 2 with a comprehensive five-year warranty* which covers defects in materials and workmanship through fair wear and tear. The warranty will be void if any other PSU other than that supplied is used. *The warranty is transferable with proof of purchase, however, warranty on ex-demonstration units begins from the retailer‘s date of purchase.
2.1 Chord Electronics ULTIMA PRE 2 | Manual _ Making a claim & warranty exclusions In the unlikely event of a claim, you must provide Chord Electronics with the details of the claim, including your original proof of purchase and serial number in order to validate the nature of the repair. Upon receipt, Chord Electronics will make an assessment within 30 days and provide a reasonable solution.
Chord Electronics ULTIMA PRE 2| Manual _ Getting to know ULTIMA PRE 2 3.0 11 // 33 3.0 3.1 Getting to know ULTIMA PRE 2 3.2 The front panel 3.3 The top panel 3.4 The back panel 3.
3.1 3.2 3.3 Chord Electronics ULTIMA PRE 2 | Manual _ Getting to know ULTIMA PRE 2 Featuring unrivalled connectivity and minimal colouration, the ULTIMA PRE 2 can be the hub of your Hi-Fi system without taking anything away from the incoming signal. With a ability to connect up to 8 inputs, a AV bypass and several outputs, ULTIMA PRE 2 offers volume and balance control giving you full autonomy over your system. ULTIMA PRE 2 also has 2 recording output for your convinience.
3.1 3.2 3.3 Chord Electronics ULTIMA PRE 2 | Manual _ The front panel Getting to know Prima The front panel The top panel 3.4 3.5 The rear panel The remote control 3.2 The front panel features the Display, Volume and Balance dials and the menu buttons. It also features the IR window which is used withe the remote and 2 1/4 heaphone jacks.
3.1 3.2 3.3 Chord Electronics ULTIMA PRE 2 | Manual _ The top panel Getting to know Prima The front panel The top panel 3.3 The top panel has no user configurable options. Instead, three teal feature light rings illuminate. Stackable Integra legs Light ring 14 // 33 3.4 3.
3.1 3.2 3.3 Chord Electronics ULTIMA PRE 2 | Manual _ The rear panel Getting to know Prima The front panel The top panel 3.4 3.5 The rear panel The remote control 3.4 The rear panel houses the device’s wide-ranging connectivity, inputs and outputs. The ULTIMA PRE 2 has several inputs and output allowing for high flexability. Mulitple inputs can be used all at the same time. When installing any cable, you must make sure that they securly click into place.
3.1 3.2 3.3 Chord Electronics ULTIMA PRE 2 | Manual _ The remote control The remote control gives you control over your full set up. The top section is reserved for Blu MKII and Dave while the bottom section is used for ULTIMA PRE 2. Your selection on the remote will show on the ULTIMA PRE 2 display screen. As the infra-red remote control requires a direct line of sight to the viewing portal, please avoid placing objects in front of either device.
Chord Electronics ULTIMA PRE 2 | Manual _ Setting up ULTIMA PRE 2 4.0 17 // 33 4.0 4.1 Placement 4.2 Connecting an input to ULTIMA PRE 2 4.3 Connecting ULTIMA PRE 2 to a power amplifier 4.4 Connecting ULTIMA PRE 2 to a recording device 4.5 Connecting ULTIMA PRE 2 to a AV device 4.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Placement Whilst the ULTIMA PRE 2 operates normally within a stack of other Full range products, it is recommended that you allow the device to breathe. Allocating 15cm of space around it to convection-cool during operation is advised. If possible, do not place the unit(s) inside a cabinet. As the infra-red remote control requires a direct line of sight to the viewing portal, please avoid placing objects in front of either device. 18 // 33 4.3 4.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Connecting an input to ULTIMA PRE 2 In order to connect up ULTIMA PRE 2 to a source, you must connect your cables to one of the inputs listed below. ULTIMA PRE 2 can have up to 8 inputs at once so it gives you the flexability to fully curate your system with minial effort required. First, you must ensure that ULTIMA PRE 2, and any connecting equipment, is turned off. 4.3 4.2 Please note that each input is arranged as a stereo pair, right and then left.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Connecting ULTIMA PRE 2 to a power amplifier 4.3 Placement 4.4 Connecting an input to ULTIMA PRE 2 4.5 Connecting ULTIMA PRE 2 to a power amplifier 4.6 Connecting ULTIMA PRE 2 to a recording device Connecting ULTIMA PRE 2 to a AV device Connecting ULTIMA PRE 2 to headphones 4.3 Using The XLR and RCA outputs shown below, it is simple to connect the ULTIMA PRE 2 to a power amplifer: 1) Turn off the ULTIMA PRE 2 and any other connected equipment.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Connecting ULTIMA PRE 2 to a recording device ULTIMA PRE 2 comes equipped with recording outputs. These are the two pairs of RCA connectors listed as the furthermost T1 and T2. These RCA outputs are always live, at line level, and cannot be attenuated. Never connect an amplifier to these connectors! You can select the input to be passed through to the recording output via the dedicated button on the front of the device. 4.3 Placement 4.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Connecting ULTIMA PRE 2 to a AV device The ULTIMA PRE 2 comes equipt with an AV Bypass mode, allowing the output of an AV surround sound processor to be connected and then routed directly to the output. You may need this when switching from a 5.1 suround sound to a 2.0 set up for audio listening. To set up with an AV unit; 1) Turn off the ULTIMA PRE 2 and any other connected equipment. 4.3 Placement 4.4 Connecting an input to ULTIMA PRE 2 4.
4.1 4.2 Chord Electronics ULTIMA PRE 2 | Manual _ Connecting ULTIMA PRE 2 to headphones If you want to use the Ultima Pre 2 with headphones, it features two 1/4 inch headphone sockets on the front panel. Headphone mode does not automatically mutes your loudspeakers. You must the amplification off. 1) Turn off the ULTIMA PRE 2 and any other connected equipment. 2) Locate the 1/4 inch headphone jacks on the front of the unit and plug in the jack. Use an adapter if needed. 4.3 Placement 4.
Chord Electronics ULTIMA PRE 2 | Manual _ How to navigate the menu 5.0 24 // 33 5.0 5.1 Basic navigation 5.2 Volume and balance control 5.3 Display 5.4 Recording 5.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ Basic navigation In order to use the ULTIME PRE 2 you can either use the buttons on the front of the unit or the remote control to navigate the menu. V.U: The V.U button can be used when you‘d like to change the view of the Volume Unit on the display screen. Button A: The A button can be used to select Bus A. Press several times to select your desired input. ULTIMA PRE 2 will remember this setting.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ Volume and balance control On your source commence playback and, using the left-hand dial, slowly increase the volume of ULTIMA PRE 2, to a safe listening level. The volume range runs from 0 to 98 and is displayed on the ULTIMA PRE 2 as you alter the volume. If the outputs are muted, a volume change will un-mute the outputs to prevent large changes in volume from damaging your loudspeakers. 26 // 33 Basic navigation Volume and balance control 5.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ Display Bus A selection: To assign the main output with a particular input signal, press the A button several times to cycle through the 7 line inputs until, the display shows the input you wish to use. The options are shown in the diagram below; 27 // 33 Basic navigation Volume and balance control 5.3 5.4 5.5 Display Recording Av bypass 5.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ Display Volume: Use the volume knob to adjust the volume manually. A clockwise turn of the knob will increase the volume and an anti-clockwise turn of the knob will decrease the volume. The volume range runs from 0 to 98 and is displayed on the ULTIMA PRE 2 as you alter the volume. If the outputs are muted, a volume change will un-mute the outputs to prevent large changes in volume from damaging your loudspeakers.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ Recording You can record an input from another audio source or two sources at the same time. To do so first connect the recording device’s output to the T1 or T2 input (IN) sockets. Your amplifier has two input selection buses. The default bus is bus A and this is the one you would use to choose your inputs in everyday operation. The advantage of having two buses is that it allows for two recording devices to record (different inputs) simultaneously.
5.1 5.2 Chord Electronics ULTIMA PRE 2 | Manual _ AV Bypass AV Bypass mode allows the output of an AV surround sound processor to be connected and then routed directly to the output of the ULTIMA PRE 2. The volume control and signal processing are bypassed so that the signal from the AV processor reaches the power amplifier exactly as if it were connected directly.
Chord Electronics ULTIMA PRE 2 | Manual _ Special features 6.0 6.1 6.
6.1 Chord Electronics ULTIMA PRE 2 | Manual _ Gain Gain 6.1 You can adjust the input gain on you input devices so that you can align the volume levels of your different inputs. There are six settings, which are x0.50, x1.00, x1.50, x2.00, x2.50 and x3.00. Gain on Bus A inputs: Select your desired input on the remote control and then press BUS A. The display will show the currently selected gain for this input. Press the VOL + to increase gain or VOL - to decrese.