Manual

Colour V Gain dB - RCA Output V Gain dB - XLR Output
Off Max Gain 70dB 76dB
Red 64dB 70dB
Blue 60dB 66dB
Pink 58dB 64dB
Green 52dB 58dB
Yellow 51dB 57dB
Cyan 50dB 56dB
White 49dB 55dB
Huei features variable gain to attenuate the volume for high-output cartridges
and records. Use the chart below to adjust the gain to a suitable level for your
preamp or amplier. Do not adjust the gain while a signal is going through the
device. If you are unsure of which setting is appropriate, consult with your dealer.
Please note that the light range will repeat after it has fully cycled.
Moving Coil gain ranges:
Moving Magnet gain ranges:
Colour V Gain dB - RCA Output V Gain dB - XLR Output
Off Max Gain 42dB 48dB
Red 37dB 43dB
Blue 32dB 38dB
Pink 30dB 36dB
Green 25dB 31dB
Yellow 23dB 29dB
Cyan 22dB 28dB
White 21dB 27dB
Huei features a Rauch Slope rumble lter that removes mechanical noise
from the turntable. It cancels out the opposing noise from each channel whilst
keeping the original music signal intact. To engage the lter, press ‘RUMBLE’
until the sphere shows white. If no colour is displayed, the rumble lter is ‘off’.
OFF ON
Only operate within the
specied temperatures
Never drop or expose Huei
to mechanical shock
Turntables can experience unwanted hum or buzzing related to grounding
issues from the cartridge. Huei allows you to ground your turntable using a
convenient grounding post, situated above the ‘IN R’ and ‘IN L’ RCA posts. You
should always use the post to ground your device and eliminate noise.
To ground your cartridge, unscrew the locking earth-pin (we recommend three
turns) and locate the earthing wire from your turntable. Place the spade tip in
between the metal washers and hex bolt, before screwing back the locking earth-
pin thumb-tight. While a spade tip is recommended, if you have bare wire, you
can wrap this around the post and then secure the locking earth-pin.
Only use a dry cloth to
gently clean Huei
Never directly spray
liquids, including cleaners,
onto Huei
Do not allow Huei to come
into contact with liquid
Never poke objects into
the exposed connectors
No user-serviceable
parts contained. Do not
disassemble Huei. Doing
so will void your warranty.
Please contact your
original dealer in the event
of a fault
WARRANTY REGISTRATION: To
activate the three-year parts and
labour warranty, register Huei online
at: chordelectronics.co.uk/register-
product
5°C 40°C
41°F 104°F
WARNING: THERE ARE NO USER-SERVICEABLE PARTS INSIDE HUEI. DO
NOT DISASSEMBLE. DOING SO WILL VOID YOUR WARRANTY, COULD
DAMAGE YOUR UNIT AND COULD RESULT IN ELECTROCUTION.
Only connect Huei to a device capable of attenuating its output, such as a
preamplier or integrated amplier. Do not connect Huei directly to a power
amplier. Incorrect settings could cause irreparable damage to your equipment
and hearing. If in doubt, contact your supplying dealer.
If you require help or advice, we recommend contacting your supplying dealer,
who will have the best understanding of your system and will be able to offer
bespoke advice. If you require further assistance, please visit the support page
of the Chord Electronics website: chordelectronics.co.uk/get-support
@chordaudio @chordelectronics chordelectronics
chordelectronics.co.uk
Keep Huei away from carpet
and soft surfaces
Always keep away from
sources of heat and direct
sunlight
Always allow the unit to be
well ventilated
Keep away from liquids and
damp areas. Immediately
unplug if contact occurs
PLACEMENT
Input impedance MM 47,000Ω
Input impedance MC 100Ω - 3700Ω (12-step)
Input noise 1.1nV/Hz
Max output voltage 20V RMS
Equalisation response RIAA curve
Equalisation accuracy ± 0.1dB
Frequency response RIAA curve 12Hz to 25kHz
Dimensions 41mm (H) x 160mm (W) x 72mm (D)
Weight 657g
10
Eliminating ground/earth hum
12
Important information
Phono stage
User Manual
|
English V1.1
Huei
13
Specications
11
Care instructions
08
Connecting Huei to your preamplifier or amplifier
09
Removing rumble noise