User's Manual

ManualsBrandsChina Great-Wall Computer Shenzhen ManualsElectronicsDigital Frame (Wi-Fi)

eStarling Photo Frame setup and user guide

Thank you for choosing the eStarling Digital Photo Frame. Please follow this guide to setup

and use your new eStarling frame.

*** Before setting up your eStarling frame ***

Please prepare the following items before you go begin the following set up of your eStarling frame.

- your eStarling frame, along with the power supply and USB cable

- a powered on PC with Internet connection

- Internet connected WiFi network with known SSID (network name), authentication type and the corresponding

encryption key ( WEP ) or Pre-Shared Key, PSK ( WPA ), if using encryption

Setting up your eStarling Digital Photo Frame

Use your PC to visit “ www.seeframe.com ” and click “Setup Now!” and follow the installation

steps below:

Step1:

Power up your eStarling™ frame by plugging in the power cord. A message will

appear on the frame “Wi-Fi Connecting” Indicating that the frame is searching for an

available WiFi signal.

(Please Note: Some models of eStarling frame include an EXTERNAL USB WiFi Adaptoe.

If your frame includes the external adaptor, please insert the adaptor into the USB port

on the frame before powering up the frame.

Summary of content (12 pages)

PAGE 1
eStarling Photo Frame setup and user guide Thank you for choosing the eStarling Digital Photo Frame. Please follow this guide to setup and use your new eStarling frame. *** Before setting up your eStarling frame *** Please prepare the following items before you go begin the following set up of your eStarling frame.
PAGE 2
Step2: Use the included USB cable to connect your eStarling™ frame to your Mac or PC (then click “Next”) Step3: You will reach the page “ www.seeframe.com/inside2.html “ for downloading the WiFi connection setup utility – NETCONFIG Choose the correct Operating System (Windows or Mac) and click “Download Now!” to start downloading NETCONFIG. Leave this webpage open after download of NETCONFIG has been completed.
PAGE 3
Setting up the WiFi connection between your WiFi router/AP and eStarling frame I. After you powered up your eStarling frame at Step1: above, you will see the eStarling logo and the frame will start to search for the WiFi network. II. For the first time setup of your eStarling frame, the following message may show up (this step may takes as long as 2min.) III. Run the NETCONFIG utility downloaded from Step3 above.
PAGE 4
************************************************************************************** NETCONFIG will jump to the last step directly if : 1) your PC had been connected/is connecting to the WEP encrypted network, NETCONFIG will automatically extract the encryption key from your PC 2) the selected network is of OPEN type, no encryption is implemented Click “Configure Frame” to send the configuration data to your eStarling frame and go to step VI.
PAGE 5
- For WEP encrypted network, enter the WEP encryption key and choose the encryption mode (choose none for open network). - For WPA encrypted network, enter the WPA Pre-Shared Key (PSK) and the encryption key type (if you are not sure, try TKIP first as this is the most common type) Click “Next” when completed. VI. A summary of the WiFi network setting will be displayed on the left hand side.
PAGE 6
****************************************************************************************** VII. It is important to disconnect the USB cable, power down the eStarling frame and power it up again. (Re. : You will be reminded to unplug the USB cable from the eStarling frame and power off and on the eStarling frame again after you click the “Configure frame” button from the above step. VIII.
PAGE 7
IX. Pls go back to the webpage opened at Step3 above and click “Next” to start the registration procedure by entering the registration code. Once the registration has been completed, the following message will be displayed on the frame (time to be taken for the frame to display this message will vary depends on different connection environment and usually it takes no more than 2 min): When this message pops up, your eStarling photo frame has been fully configured and ready for use. X.
PAGE 8
If the eStarling Frame has been connected to the specified WiFi network but the network is not being connected to the Internet, the following message will be displayed. Please contact your ISP and check on the Internet connection to your WiFi network. Once the Internet connection has been re-established, the frame should automatically connect to the www.seeframe.com and provide you the six digitals registration code in red as above mentioned. Or, pls go through the Wifi connection setup procedure again.
PAGE 9
Congratulations, your eStarling photo frame has been properly setup to communicate with www.seeframe.com. You can enjoy the ultra convenient way of photo sharing which we enabled through eStarling Frame and www.seeframe.com . Photos under your user account on www.seeframe.com will be sent automatically to your eStarling frame through Internet and your WiFi network. When the on-frame memory is full, photos will be deleted from the frame in a “first-in-first-out” manner.
PAGE 10
From memory card : Photos on FLASH memory cards will have a higher priority for display than those being pushed from the web server. Slide shows from memory card will be started from the last memory card you inserted into the eStarling photo frame automatically 2. Adjusting time interval between photos under auto slide show mode The default time interval between each photo for auto slide show is 10 sec. You can toggle the options between 10, 60 second 180 sec.
PAGE 11
Photos from FLASH memory card can be uploaded directly to your web album under www.seeframe.com . Stop the slide show by pressing the STOP button, browse through the photos using the NEXT and PREVIOUS button and locate the photo to be uploaded. Press the UPLOAD button once and the screen will display: Once the photo has been completed uploaded, the following message will be displayed FCC Information This device complies with Part 15 of the FCC Rules.
PAGE 12
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.