Installation instructions

ManualsBrandsChief ManualsRemote ControlsIR10

INSTALLATION INSTRUCTIONS

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

Infrared Remote Control Accessory

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

IR10

Summary of content (10 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Infrared Remote Control Accessory Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description IR10
PAGE 2
IR10 Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
PAGE 3
Installation Instructions IR10 LEGEND Tighten Fastener Loosen Fastener Apretar elemento de fijación Aflojar elemento de fijación Befestigungsteil festziehen Befestigungsteil lösen Apertar fixador Desapertar fixador Serrare il fissaggio Allentare il fissaggio Bevestiging vastdraaien Bevestiging losdraaien Serrez les fixations Desserrez les fixations TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/8" B (1) A (1) C (1) 3
PAGE 4
IR10 Installation Instructions INSTALLATION (B) WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! All wiring should be performed by a properly trained and licensed electrician following all local ordinances. NOTE: This device can provide control of any device set up for momentary dry contact inputs. See Dry Contact Closures section. Locate and Install IR Receiver The IR receiver consists of two parts.
PAGE 5
Installation Instructions 4. IR10 Using a slotted screwdriver, connect power and signal wires to the IR to Dry Control accessory (A).
PAGE 6
IR10 Installation Instructions Changing System Codes Settings are changed by a combination of remote button presses and partially disassembling the box to change specific jumper settings. NOTE: For changing what the box expects to receive, you need to remove the housing and remove a jumper (J5). 1. 2. 3. Remove four Phillips screws from housing and remove housing cover. (See Figure 4) Remove jumper. (See Figure 4) Replace housing cover and four screws removed in Step 1.
PAGE 7
Installation Instructions IR10 OPERATIONS Dry Contact Closures The IR-10 provides dry contacts based on IR input. Example: Pressing the ’UP’ button on the remote will cause a connection to be made between COM and C1. This connection can be used to trigger other devices (SL, Cinematic, or any third party device that required this type of input). NEC Protocol COM The modulated carrier is usually derived from 455kHz and is 1/12 of the frequency with 1/3 duty cycle.
PAGE 8
IR10 Installation Instructions Figure 6 8
PAGE 9
Installation Instructions IR10 9
PAGE 10
IR10 Installation Instructions USA/International Europe Chief Manufacturing, a division of Milestone AV Technologies 8820-000027 Rev A 2008 Milestone AV Technologies www.chiefmfg.com 07/08 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA.