ZigBee Module ZM11 Product Manual
Mechanical Drawings ABSOLUTE MAXIMUM RATINGS VIN to GND ……………………………..-0.3~3.5 V Other Pin to GND…………………………-0.3~3.5V RECOMMENDED OPERATING CONDITIONS Vcc to GND ……………………………..3.3 V+- 5% Operating temperature …….………….....
RF SPECIFICATIONS Frequency Band …………………………..ISM 2.4 GHz TF Tx power………………………………………17 dBm max Antenna Efficiency…………………………….
Pin Signals 1. Power Supply Pin and Common pin Pin# Pin Name Pin Type Description 2 VCC RF PW 3.3V RF Power supply 4 VCC PW 3.3V Digital Power Supply 1,3,5,9,23 GND PW Ground 21 BM AI Battery Monitor Pin 22 RST DI Module Reset Input 7 LED0 DO LED0 pin (active 0,output current 4mA), controlled by module 6 LED1 DO LED1 pin (active 0,output current 4mA) 20 KEY DI Push Button Input pin low-active 2.
Router Multi Function pin Table FS1 FS2 FS3 FS4 FS5 FS6 FS7 FS8 FS9 FS10 UUU UUF UFU UFF FUU FUF FFU UUD UDU FFF ADC 4 2 PWM 4 2 2 2 4 4 2 2 4 DI 2 DO I2C 1 UART 1 2 1 1 4 6 8 1 1 1 1 Pin 14 PWM3 I2C DI1 DI1 DI1 DI1 DI1 DI1 PWM0 DI0 DI0 DI0 DI0 DI0 DI0 ADC0 DO1 DI3 DI3 UART DI3 DI3 UART SDA 15 PWM2 I2C SCL 16 ADC3 UART RT 17 ADC2 UART RT DO0 DI2 DI2 CT 18 ADC1 UART ADC0 UART DI2 DI2 CT ADC1 DO1 DO1 TX 19 UART RT
End Device Multi Function pin Table FS6:LS FS6:DS FS7:LS FS7:DS FS8:LS FS8:DS FDF FDD DDF DDD DFF DFD 2 2 6 6 8 8 ADC PWM DI 4 4 1 1 14 DI1 DI1 DI1 DI1 DI1 DI1 15 DI0 DI0 DI0 DI0 DI0 DI0 16 UART UART DI3 DI3 DI3 DI3 RT RT UART UART DI2 DI2 DI2 DI2 CT CT UART UART ADC1 ADC1 DI5 DI5 TX TX UART UART ADC0 ADC0 DI4 DI4 RX RX 12 DI3 DI3 DI5 DI5 DI7 DI7 13 DI2 DI2 DI4 DI4 DI6 DI6 DO I2C UART Pin# 17 18 19 Note : LS=Light Sleep
Typical application for Function set 2 Analog Input pin (BM,ADC) CHARACTERISTICS Input resistance, signal …………………….. 200k ohm (Typ) ADC full scale range ……………………….0~1.15 V Digital output(DO,PWM,UART TX,UART RT,LED) DC CHARACTERISTICS Logic-0 output voltage ………………. 0.5V(max) @ output load 4mA Logic-1 output voltage ………………. 2.4V (min) @ output load 4mA Digital Input(DI,UART RX,UART CT, KEY ,Reset) DC CHARACTERISTICS Logic-0 input voltage(VIL max)…………..0.5V Logic-1 input voltage(VIH min)…………..2.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Note: The end product shall has the words “Contains Transmitter Module FCC ID: 2AOWSIWAZBZM11“ Further instruction to OEM relating to Part 15B/RF exposure subject to be re-evaluating while the module is installed to the host shall be given
