VT-M2M-BTA-DE User’s Manual Vantron Technology www.vantrontech.
VT-M2M-BTA-DE Revision History: No. 1 2 3 Version V1.0 V1.1 V1.2 4 V1.3 Description First release Modify description of COM Add software part 1. Update the safety Instructions 2. Add antenna description Date June.17, 2014 June.
VT-M2M-BTA-DE Table of Contents Part I：Hardware Platform .................................................................... 4 1 Foreword........................................................................................ 5 1.1 Copyright Notice ................................................................... 5 2 1.2 Notes.................................................................................... 6 1.3 Statement...........................................................................
VT-M2M-BTA-DE 3.6 3.5.2 Ethernet Interface ................................................. 20 3.5.3 D Sub-9 RS232 Connector...................................... 21 3.5.4 RS232/485 ,CAN,External IO Connector ................. 22 3.5.5 VGA Interface........................................................ 23 3.5.6 USB Host Connector .............................................. 23 Operation Notice ................................................................ 25 3.6.1 Change SIM Card........
VT-M2M-BTA-DE
VT-M2M-BTA-DE Part I：Hardware Platform
VT-M2M-BTA-DE 1 Foreword 1.1 Copyright Notice While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Vantron assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
VT-M2M-BTA-DE 1.2 Notes Applicable notes are listed in the following table: Sign Notice Type Description Notice Important information and regulations Caution Caution for latent damage to system or harm to personnel 1.3 Statement It is recommended to read and comply with this manual before operating VT-M2M-BTA which provides important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to the device. 1.
VT-M2M-BTA-DE information. Pay attention to warnings on this device. Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device. Operations and Service instructions are provided with the equipment. Unit shall be used with indoor-use antenna only. No antenna for this unit can be installed outdoor. The maximum operation temperature is 61°C. 1.
VT-M2M-BTA-DE 1.8 Safety Instructions for Power Cables and Accessories Proper power source only Start only with power source that satisfies voltage label and the voltage necessary according to this manual. Please contact technical support personnel of Vantron for any uncertainty about the requirements of necessary power source.
VT-M2M-BTA-DE 2 Overview 2.1 Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state-of-the-art technology and the best product services. Vantron’s M2M products are based on the most advanced ARM and Intel Atom processors and have low-power consumption and high integration. The products are designed for applications of M2M in industrials, medicals, financial, retail, vehicle, and transportations etc.
VT-M2M-BTA-DE 2.2 Product Series 2.2.
VT-M2M-BTA-DE 2.2.2 Ordering Information Order Examples: VT-M2M-BTA-DE-S-1GM-16GF-G ATOM Baytrail single Processor, 1GB DDR3L, 16GB SSD, 3G, WiFi, GPS, extended temperature WP-I VT-M2M-BTA-DE-Q-1GM-16GF-W ATOM Baytrail quad Processor, 1GB DDR3L, 16G SSD, WiFi, GPS, commercial temperature P Accessories: Install Mechanical tools,1pc Power Adapter with locked connector (Optional),1pc IO Terminal (12x3.
VT-M2M-BTA-DE 3 M2M-BTA Hardware Instructions 3.
VT-M2M-BTA-DE View for all optional embedded modules and antennas
VT-M2M-BTA-DE Bottom View for optional embedded modules (1xHalf PCIe slot under the 1xPCIe slot) Top View for thermal module
VT-M2M-BTA-DE 3.2 Specifications Specifications CPU Processor Intel® ATOM™, E3827/1.75GHz, E3845/1.91GHz, E3815/1.46GHz Memory On Board RAM ROM Internal On Board DDRIII 1333MT/s(E3845&E3827)/ 1066MT/s (E3815), up to 2GB 1.8”SATA SSD Module Internal (16GB, or others) On board SATA2.
VT-M2M-BTA-DE Security Alarm Buzzer Out SD card 1xSD card Slot (Optional ) RTC Supported Control Reset Button in the front,Power button in the back GPIO Reserved GPIO (Terminal) CAN 1x CAN2.0b security On board Registration Serial Number, and SHA-1 Encrypt/Decrypt Chip DS28E01 (Optional) TPM on board Software Power OS Windows, or Linux Applications SDK Available Input DC9-36V(default 12V), Locked Power Jack Consumption 6W (Pulse8W), Sleep 2W.
VT-M2M-BTA-DE 3.3 Interface Instructions 3.3.1 Front View 3G / GPRS Antenna(3G Band) Antenna Gain:1dBi WLAN / ZigBee Antenna(2.4G Band) Antenna Gain:3.2dBi GPS Antenna(1.
VT-M2M-BTA-DE 3.3.
VT-M2M-BTA-DE 3.
VT-M2M-BTA-DE 3.5 Interface Description 3.5.1 Wide-Range Power Interface Power JACK with lock Pin Description 1,3 DGND (ground pin) 2 Power (+12 DC,UP to 36V) 3.5.
VT-M2M-BTA-DE 3.5.
VT-M2M-BTA-DE 3.5.4 RS232/485 ,CAN,External IO Connector 12pins 3.81 pitch terminal with screw lock Load capacity: more than 128 nodes/RS485 channel Pin 1 2 3 4 5 6 7 8 9 10 11 12 Description TXD2/485_2_A RXD2/485_2_B DGND CANH CANL DGND EXTIO0 EXTIO1 EXTIO2 EXTIO3 EXTIO4 EXTIO5 Remarks BIOS set BIOS set 3.3V Level 3.3V Level 3.3V Level 3.3V Level 3.3V Level 3.
VT-M2M-BTA-DE 3.5.5 VGA Interface Standard vertical DB-15 Female VGA connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3.5.6 USB Host Connector Dual vertical USB A type interface, USB2.0 Description RED GREEN BLUE N.C. GND GND GND GND +5VDC GND N.C.
VT-M2M-BTA-DE Pin A1 A2 A3 A4 B1 B2 B3 B4 Description USB1_VCC(+5VDC) USB1_DUSB1_D+ USB1_DGND(ground pin) USB2_VCC(+5VDC) USB2_DUSB2_D+ USB2_DGND(ground pin)
VT-M2M-BTA-DE 3.6 Operation Notice 3.6.1 Change SIM Card Push the small button on the left of SIM Card Holder, and install the SIM card to the holder. Then push the holder into the Slot. 3.6.2 Power Supply Please make sure using adapter in the accessory, or the power is not reversed when powered by other adapter.
VT-M2M-BTA-DE 4 Tips Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister.
VT-M2M-BTA-DE Keep away from all energized circuits. Operators should not remove enclosure from the device. Only the group or person with factory certification is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not change components unless the power cord is removed. In some cases, the device may still have residual voltage even if the power cord is removed.
VT-M2M-BTA-DE Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs. Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this manual may be reprinted or publicly released in forms of photocopy, tape, broadcast, e-document, etc.
VT-M2M-BTA-DE Part II：Software Reference
VT-M2M-BTA-DE 1. Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state of the art technology and the best product services. Vantron’s M2M products are based on the most advanced ARM and Intel Atom processors and have low power consumption and high integration. The products are designed for applications of M2M in industrials, medicals, financial, retail, vehicle, and transportations etc. 1.
VT-M2M-BTA-DE 1.3 VT-M2M-BTA-DE Features The below table lists VT-M2M-BTA-DE features. Device Description Name VGA Maximum resolution up to 2560x1600@60 Hz COM Ports Driver: CD\\WIN7 Driver\\Graphic\\ Intel_EMGD.WIN7_PC_Version_36_15_0_1073.
VT-M2M-BTA-DE Guide\\VT-M2M-BTA GPIO Programming.pdf CAN Support CAN V2.0B protocol Green Terminal Pin 4 - CANH Green Terminal Pin 5 - CANL Ethernet Test by tool: CD\\SW Guide\\CAN Test\\ Test_COM2CAN_Net20_v1.0.zip Test Guide: CD\\SW Guide\\CAN Test\\ Test_COM2CAN_Net20_v1.0.zip 2 x Intel 82574 Audio Realtek ALC269 USB Port Driver: CD\\WIN7 Driver\\Audio \\32bit_Win7_Win8_Win81_R273.exe Support USB 2.0 protocol, 2 x USB2.0 slot USB CAN, 3G and WIFI need USB3.0 driver SD Card Driver: CD\\WIN7 Driv
VT-M2M-BTA-DE WIFI User Guide: CD\\SW Guide\\Accelerometer test\\Test_ADXL345_BayTrail_Net20_v1.0.zip Intel N62205 3G Driver: CD\\WIN7 Driver\\Intel WIFI 62205ANHMW\\intel_wireless_14.2.0.10_s64.exe Telit HE910 User Guide: CD\\WIN7 Driver\\Telit HE910\\HE910 Use guide.pdf Driver: CD\\WIN7 Driver\\Telit HE910\\Telit_xE910_HE863_USB-Driver_Win_desktop_OS_ U8.00.04.zip Telit DE910 User Guide: CD\\WIN7 Driver\\Telit DE910\\DE910 Use guide.pdf Driver: CD\\WIN7 Driver\\Telit DE910\\ Telit_UC_CC_DE_CE_USB_Driv
VT-M2M-BTA-DE USB HUB User Guide:CD\\SW Guide\\DIGI Zigbee\\ZigBee ZGB XB24 user guide.pdf SMSC 4604 Driver: CD\\WES7 Driver\\Smsc USB HUB 4604\\smsc_protouch_mpt_4.1.9.0_setup.exe.
VT-M2M-BTA-DE 2. Base Control Turn on the product, boot to Windows. 2.1 CAN Control This test application use to test COM2CAN communication, it support 32bits system. Please install Microsoft .Net 2.0 or above version and USB2COM Driver in advance before run the application .
VT-M2M-BTA-DE Step Details: 1. Prepare 2 devices, and connect CAN. 2. Enter windows7, look up COM number of USB2COM in device manager. 3. 4. 5. 6. According to the step2, select COM14 and set CAN speed to 500k(support 20k,50k,100k,125k,250k,500k,1M), Open device. Input data in first TextBox in “CAN Tx” GroupBox, Click “Send String” Button on one device, then “Tx Len” will record length of all data sent( Click “Clear TxLen” to set TxLen = 0) .
VT-M2M-BTA-DE t 000 4 55555555 Fixed value, present send data ID, use 3 decimal char Send data Length Hexadecimal string, Represent data “uuuu” 2.2 GPIO Control Configure by BIOS option: Advanced >> Onboard Devices Configuration >> GPIO Configguration 2.3 Serial COM Control a. Run TestCommPC V2.3.3.
VT-M2M-BTA-DE b. Select PORT COM1 or COM2, select BAUD 115200, click ”Open”. c. Click “AutoTx”, COM1 transmit the data below cyclically. If connect the pin2 and pin3 of COM1, it will receive the data, and show on the right.
VT-M2M-BTA-DE 2.4 Audio and Video Control a. It can play sample music.
VT-M2M-BTA-DE b. It can play sample video.
VT-M2M-BTA-DE 2.5 SD card Control a. Insert SD card , then look over device: 2.6 ADXL345 Control a. Run Test_ADXL345_BayTrail_Net20.exe, click “start Detect”.
VT-M2M-BTA-DE b. Shake the product, the value of X,Y,Z will change.
VT-M2M-BTA-DE 3. Network Module 3.1 WIFI Control a. Click the network icon, choose the WIFI, Enter the password, click the OK icon.
VT-M2M-BTA-DE 3.2 3G Control HE910 only support WCDMA. a. Click the network icon, choose the HE910, click the connect icon. b. Click dial icon. Tip: If it fail, try again.
VT-M2M-BTA-DE DE910 only support CDMA2000. a. Fill the Username: “card”, Password: “card”, Number: “#777”.
VT-M2M-BTA-DE 4. GPS Module a. Click RCT-1[1].1.0BETA.exe, use the right key of the mouse, choose Run as administrator. b. Click COM icon, choose COM3, 38400.
VT-M2M-BTA-DE c. Click OPEN icon, starting receive data.
VT-M2M-BTA-DE 5. ZigBee Control a. Install 40003002_B.exe, when it finish, it will generate X-CTU. b. Run X-CTU, choose Communication port(COM4). c.
VT-M2M-BTA-DE 1. Input “+++”, ZigBee respond “OK”. 2. Input “atce 1”, ZigBee respond “OK”. 3. Input “atcn”, Zigbee respond “OK”. 4. Wait a few seconds, Zigbee enter since the resumption of spontaneous mode. For an example, input ”a”, when Zigbee respond “a”.
VT-M2M-BTA-DE US Office: Vantron Technology, Inc. Address: 1292 Kifer Road #807, Sunnyvale, CA 94086 Tel: 510-304-7666 Email: sales@vantrontech.com China Office: Chengdu Vantron Technology,Ltd Address: 3rd floor, 3rd building, No.9, 3rd WuKe East Street, WuHou District, Chengdu, P.R. China 610045 Tel: 86-28-8512-3930/3931, 8515-7572/6320 Email: sales@vantrontech.com.
