Leviathan 5000 User Manual
Thanks for choosing Leviathan intelligent Wave pump. Please read the user manual clearly before use. SAFETY GUIDE Attached are the warning level with different situation.
SAFETY GUIDE HANDLING OF POWER PLUG , POWER CORD & SOCKET WARNING Dust on ballast needed to be cleaned regularly. Accumulated dust may cause fire due to moisture. Please wipe off with a dry cloth. Unplugging the power during maintenance. It may cause an electric shock. INSTALLATION WARNING Do not install in places where the power cord or ballast get wet. There is a possibility of electric shock and leakage. Do not install in places that get hot (closed fire, heat appliances, under the sun, etc.
●Package contents / Name of each part Rotor Pump Body Pump case External Magnet Interior Magnet Intelligent Controller Power cable Cable Holder Connection cable Ballast Screws for Controller placement Protection Sponge ●Before Use .This product only use inside water. ATTENTION.Compensation for the live stock is not performed by stopping the pump. ·Make sure that the pump does not run idle due to a drop in water level, etc.
●Specification Model Leviathan 5000 FLOW RATE 50∼20,000 L /h 150∼2,200L SUITABLE FOR AQUARIUM MAX. POWER CONSUMPTION 24W(±5%) MIN. POWER CONSUMPTION 0.4W(±5%) Max. 20mm GLASS THICKNESS Max. Glass thickness 20mm 74 ㎜ 80 ㎜ 15 ㎜ 95 ㎜ ●INSTALLATION Do not turn on the power when the pump is not setting up correctly inside the water. 1. Please clean the glass which you plan to place the external magnet. 2. Place the pump in correct place and slide the external magnet close to the internal magnet.
5. CONNECTION GRAPH CONTROLLER POWER CORD BALLAST PUMP FOR SAFTLY USE THIS PRODUCT , PLEASE CONNECT EACH PARTS IN THE CORRECT WAY FROM ABOVE PICTURE. MAKE SURE TO SETTING UP DRILL LOOP IN EACH WIRE AND LOCK THE CONNECTOR FIRMLY. ATTENTION THE PUMP WILL AUTOMATIC TURN ON IN MIN. POWER(5%) WHEN YOU CONNECTED ALL PARTS AND THE POWER CORRECTLY. ●FLOW DIRECTION ADJUSTMENT ADJUSTABLE ●Cable & Controller placement ①Cable arrangement Use the cable holder to fix the cable as your wish.
●CONTROLLER INTRODUCTION ●HOME RETURN TO HOME PAGE ●RETURN RETURN TO LAST PAGE ●HOME SCREEN Entry:Current Wave schedule.(Details please check “Wave schedule setting”) Number:Current link up pumps. Mode:Current mode of wave setting. Time:Current wave setting operate time period. Week:Current wave setting operate days in a week. Speed:Current Speed (RPM) of the pump. Power:Current power consumption of the pump. Wave ICON( ): Setting wave schedule and details.
●WAVE SCHEDULE SETTING Setting up Wave schedule by different mode , time period and days. You can setting up to 16 schedule per day. 1. Click on Wave ICON ( ) Press the dial, Wave1, Wave2, Wave3.... and the Wave settings are displayed. (e.g.WAVE1 is working on the left picture. ) 2. Turn the dial to WAVE1 and press the dial to enter the setting screen. (Status , Mode , Time and Save will display at the screen) Status: Turn on this schedule with ON /OFF.
Mode: You can choose the wave mode. There are 4 pre set Mode :Constant , Rough sea , Tide ,Random. And Customs allows to fully setting up all details by advanced aquarist. All settings are allowed to setup details separately. Co n s ta n t Pumps are working with constant flow. When you select constant, you will see the left screen, and you can set the power of the flow with Max. speed. The graph below shows the pump's power, the horizontal axis is the elapsed time, and the operation of the pumps being set.
Random The gap between the strength and the wave becomes a random wave. If you select Random, the left screen will be displayed. You can set the following items on this screen. Max Speed: Maximum wave power Min Speed: Minimum wave power Custom Fully custom wave pattern for advanced aquarist 。 If you select Random, the left screen will be displayed. You can set the following items on this screen.
Save: Make sure to save after adjust the setting in each wave schedule .It will not response if you didn’t save the setting. ●Setting of multiple wave schedule You can set the time period and the day of the week to schedule. Wave2, Wave3... after setting up Wave1.The schedule can be set up to 16 schedule per day(Wave1 to 16). E.g.: If the Wave1 and Wave2 time settings conflict, the priority will follow the first schedule .In this case , the schedule will follow Wave1.
●Multiple Leviathan connection Leviathan can be connected up to 4 units. 【Method】 ①Each leviathan is placed in aquarium. ②Click to Setting ICON , and click to Mode , assign 1 Leviathan for a Master unit and others are setting to be Slave unit ③Leviathans will automatic connected after restart from changing Mode。 ④After pumps connected in a loop , all slave unit will follow the wave schedule from Master unit.
)&& 6WDWHPHQW :NOY JK\OIK IUSVROKY ]OZN VGXZ UL ZNK ,)) X[RKY 5VKXGZOUT OY Y[HPKIZ ZU ZNK LURRU]O TM Z]U IUTJOZOUTY ZNOY JK\OIK SG_ TUZ IG[YK NGXSL[R OTZKXLKXKTIK GTJ ZNOY JK\ OIK S[YZ GIIKVZ GT_ OTZKXLKXKTIK XKIKO\KJ OTIR[JOTM OTZKXLKXKTIK ZNGZ SG_ IG[ YK [TJKYOXKJ UVKXGZOUT )G[ZOUT )NGTMKY UX SUJOLOIGZOUTY TUZ K^VXKYYR_ GVVXU\KJ H_ ZNK VGXZ_ XKYVUTYOHRK LUX IUSVROGTIK IU[RJ \UOJ ZNK [YKXȑY G[ZNUXOZ_ ZU UVKXGZK ZNK KW[OVSKTZ 45:+ :NOY KW[OVSKTZ NGY HKKT ZKYZKJ GTJ LU[TJ ZU IUSVR_ ]OZN ZNK R