SZU06C2 Product Manual SZU06C2 ZIGBEE WIRELESS COMMUNICATION MODULE Product Manual
SZU06C2 Product Manual Table of Contents Table of Contents....................................................................................................................................................... 1 1 General.................................................................................................................................................................... 1 1.1 Module introduction....................................................................................................
SZU06C2 Product Manual 12.3 Storage conditions.....................................................................................................................................21 13 Packaging...........................................................................................................................................................22 13.1 Carrier tape...............................................................................................................................................
SZU06C2 Product Manual Module features Mini 33-pin stamp-like SMT package Provide on-board snake antenna Small form factor: 19 mm x 25 mm x 3.7 mm Compliant with EU CE certification Compliant with EU RoHS certification Compliant with EU ATEX certification Based on ARM Cortex®-M4 architecture 256K FLASH and 32K RAM Multiple sleep modes Operating voltage range: 2.1V to 3.
SZU06C2 Product Manual RF Features Based on the Silicon Labs EFR32MG1 chip solution 2.4 GHz ISM frequency band 250 Kbps data transmission rate over the air 16 channels (IEEE802.15.4: CH11–CH26) Maximum output power: +19.5dbm Signal sensitivity: -101dBm@1% PER Sleep current: 3.0μA RX current :13.7mA TX current: 139mA @+19.5dBm Visible barrier-free communication distance: 1300 m@-69dBm, PER=0.
SZU06C2 Product Manual 1 General 1.1 Module introduction SZU06C2 introduced in this document is an embedded wireless communication module based on IEEE802.15.4/ZigBee technology. The hardware has taken the EFR32MG1B232[1] chip solution of Silicon Labs and the software adopts the SZU06 AT command set self developed based on Ember Z-net_5.9.0 protocol stack released by Silicon Labs.
SZU06C2 Product Manual Module Chip FLAH RAM Sealing Dimension SZU06C2 EFR32MG1B232 256KB 32KB 19mm * 25mm * 3.7mm Table 1- 1 Model of SZU06C2 Module The SZU06C2 is used for ZigBee applications (www.zigbee.org). If you don’t want to use the AT command interface we provided and expect to develop your own software, you need to download the official Simplicity Studio V4 development tool and Ember Z-net_5.9.0 or later protocol stack of Silicon Labs. 2 Approvals 2.
SZU06C2 Product Manual The "CE" marking must be placed in a prominent position of OEM products. Please refer to http://ec.europa.eu/enterprise/faq/ce-mark.htm for more information about CE certification mark. Important tips: In Europe, frequency band of 2.4GHz is used only for the equipment with the maximum equivalent isotropically radiated power (e.i.r.p.) of less than 10mW(10dBm). In case that e.i.r.p.
SZU06C2 Product Manual two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SZU06C2 Product Manual 2.3 ATEX Approvals The SZU06C2 ZigBee wireless communication module has been tested to comply with the ATEX 2014/34/EU regulation about explosion proof products. Intended Use:Zone 2 GAS. This device meets the following parameters: Ui =3.9V, Ii =1A, P=0.98W, Ci =15.32 μF, Li =5.64μH, -40℃ Ts 80 ℃.
SZU06C2 Product Manual partial certification may be used as a basis for certification of equipment or protective system. 2. The maximum input parameters stated above shall be considered during installation. The rules for interconnection of intrinsically safety circuits according EN 60079-11 and EN 60079-14 have to be taken into account. 3. The maximum service temperature of the communication module when incorporated into apparatus is -40°C to +80°C.
SZU06C2 Product Manual 3 Module Pinout Fig. 3- 1 SZU06C2 Pinout (top view) In order to facilitate the user to develop and design the products based on SZU06C2 ZigBee wireless communication module, we have detailed the pin information of SZU06C2 ZigBee wireless communication module in the following Table 3-1. All GND pins are directly connected with the module; but for best RF performance, each GND pin shall be connected to a complete ground externally . Pin No.
SZU06C2 Product Manual 12 NC - - Float directly. 13 GND GND - System GND. 14 PTI.SYNC PB13 R/RW General GPIO 15 PTI.DATA PB12 R/RW General GPIO 16 PTI.CLK PB11 R/RW General GPIO 17 TXD PA0 R/RW Transmitted Data 18 RXD PA1 R/RW Received Data 19 GND GND - System GND. 20 GND GND - System GND.
SZU06C2 Product Manual 4 Hardware Description 4.1 Hardware Diagram Fig. 4-1 Hardware Diagram of SZU06C2 SZU06C2 wireless communication module is based on EFR32MG1B232 chip from Silicon Labs, which integrates the RF transceiver complying with 2.4-GHz IEEE 802.15.4, high performance 32-bit 40MHz ARM Cortex®-M4 CPU, 256KB FLASH and 32KB RAM which can be programmed in the system and many other peripherals with strong functions.
SZU06C2 Product Manual 4.2 Interface characteristics Test conditions Parameter UART Baud Rate Analog channel resolution Minimum value Maximum value Unit 9600 115200 bps 6 12 bit Half-duplex Analog input impedance Typical values 20 Analog input voltage 2.1 GPIO output voltage -0.3 Real-time clock frequency 3.3 32.768 kΩ 3.9 V 3.9 V kHz Table 4-1 SZU06C2 Interface Characteristics 10 SZU06C2 PM(Rev 2.
SZU06C2 Product Manual 5 Absolute Maximum Ratings Parameter Symbol Min value Max value Unit Supply voltage VDD -0.3 3.9 Supply current IVDD - 1000 Pin voltage VPIN -0.3 3.9 V RF input level Pmax - 10 dBm Output power Pout -26 19.
SZU06C2 Product Manual 5.2 Recommended operating conditions Parameter Min value Typical value Max value Unit Environment Supply voltage 2.1 3.3 3.9 V RF input power - - 10 dbm 2480 MHz RF frequency 2405 Operating temperature -40 25 85 ℃ - - 95 % Relative humidity - Table 5-3 Recommended Operating Conditions 6 DC Electrical Characteristics VDD 3.3V,TOP 25℃，fC 2400MHz 2483.5MHz. Parameter Test condition Symbol Value Min. Type Max. Supply Voltage VDD 2.1V 3.
SZU06C2 Product Manual Enter EM4 mode Wake up time - 0.5μA - From EM1 to wake t em 1 w u - 3μs - From EM2 to wake t em 2 w u - 3μs - From EM3 to wake t em 3 w u - 3μs - From EM4H to wake t em 4 h w u - 20μs - From EM4S to wake t em 4 s w u - 290μs - Table 6-1 DC Electrical Characteristics of SZU06C2 7 Digital IO Specifications VDD 3.3V,TOP 25℃. Parameter Sym Test conditions bol Parameter value Min. Logic0 input voltage VIL Logic1 input voltage VIH 0.
SZU06C2 Product Manual AC Electrical Characteristics 8 VDD =3.3V,TOP =25℃. No 1 Parameter Test conditions Frequency range Min Typ. Max 2400 2500 CH11 CH26 Unit MHz See Table 10.2 for the 2 Channel number correspondence between channel and frequency 3 Input impedance 4 Receiver sensitivity PER=1% 5 Input level Input voltage PER=1% High-side adjacent channel 7 50 53 Ω -102 -101 -99 dBm 10 dB Interferer is reference - 33.
SZU06C2 Product Manual RSSI accuracy in the linear 11 - region as defined by ±1 - dB 802.15.4-2003 12 Frequency Tolerance for 38.4 MHz, ESR = 50 Ω, the crystal CL = 10pF Occupied channel 13 bandwidth per ETSI EN300.328 14 15 16 99% BW at highest and lowest channels in band Error vector Output power at lowest magnitude(EVM) power setting:19.5dBm Actual maximum output Output power at lowest power power setting:19.
SZU06C2 Product Manual Physical Dimensions and Footprint 9 9.1 Physical Dimensions Fig. 9-1 Physical Dimensions of SZU06C2 Parameter Parameter Description Parameter value W Module width 19mm L1 Module length 25mm A1 Distance between semi-holes 1.27mm A2 Distance from semi-hole to PCB 0.8mm Table 9-1 Physical Dimensions of SZU06C2 16 SZU06C2 PM(Rev 2.
SZU06C2 Product Manual 9.2 Recommended Footprint Fig. 9-2 Recommended Footprint of SZU06C2 Notes: 1. When the surface mounted SZU06C2 ZigBee wireless communication module is used, it is suggested that the bonding pad shall be 1mm wide and 1.2mm high. 2. L=25mm. 3. You must ensure that the corresponding PCB of “keep-out area” part in Fig. 3- 1shall have no any device, running line or applied copper. 4.
SZU06C2 Product Manual 10 Soldering Temperature Time Profile (for reflow soldering) 10.1 Recommended temperature time profile for lead-free solder Fig. 10-1 SZU06C2 Temperature Profile for Lead-free Solder Notes: Preheat: The recommended temperature climbing speed shall be 2℃/s and not exceed 2.5℃/s at the preheat area. Cooling: The recommended temperature descent speed shall be 3℃/s and not exceed 4℃/s at the cooling area.
SZU06C2 Product Manual 11 Reliability Test To guarantee the environment adaptability of SZU06C2, we have done the the following measurements. No Test items Test methods 1 Vibration test Setting the vibration frequency of 50Hz, amplitude of 1.
SZU06C2 Product Manual 12 Application Precautions 12.1 Safety precautions Before use of SZU06C2, check and evaluate their operation when mounted on your products . These products may short-circuit.
SZU06C2 Product Manual The environment of direct sunshine, outdoor or dusty environment Environment easy to condensation Environment with high concentration and harmful gases (such as air with salt, muriatic acid, chlorine, sulfur dioxide, sulfuretted hydrogen, ammonia gas or nitrogen oxide) （5）Mechanical stress shall be avoided in assembly or operation of SZU06C2.
SZU06C2 Product Manual 13 Packaging 13.1 Carrier tape Fig. 13-1 Dimension of Carrier Tape (Top View) Fig. 13-2 Diagram of Cover Tape Fig. 13-3 Diagram of 22 Empty pocket SZU06C2 PM(Rev 2.
SZU06C2 Product Manual Fig. 13-4 Orientation of SZU06C2 13.2 Reel Fig. 13-5 Reel Dimensions Each reel will be packed in a electrostatic shielding bag 23 SZU06C2 PM(Rev 2.
SZU06C2 Product Manual 14 Ordering Information Product code Brief description SZU06C2 Based on EFR32MG1single chip solution On-board snake antenna 19mm * 25mm * 3.7mm Visible barrier-free communication distance is 1300m @-69dBm Development kit contains SZU06DVK Development Kit 2 X SZURF-EVB Development Boards 2 X SZU06A1 on Carrier-Board 2 X SZU06C2 on Carrier-Board 2 X SZU06C1 on Carrier-Board 2 X SZU06C2 on Carrier-Board 2 X Pulse 2.
SZU06C2 Product Manual 15 Drawing of Product Label Fig. 15-1 SZU06C2 Product Label The label dimensions are 15.2mm*17mm and the label will withstand temperatures used during reflow soldering.
SZU06C2 Product Manual 16 Disclaimer We reserve the right to modify or improve the product, company name and LOGO at any time without prior notice. In addition, Chengdu Diyue Technology Co., Ltd. does not convey any license under its patent rights or assume any responsibility for the use of the described product.
SZU06C2 Product Manual 19 Reference Documents [1] Data sheet EFR32MG1.Silicon Labs. (www.silabs.com-EFR32MG1) 20 Contact Information Website: www.cdiyue.com Add.: 4/F, Block A, Gaofa Building, No.6, Jiuxing Avenue, High-tech Zone, Chengdu Tel: 0086-28-85138368 Fax: 0086-28-85189190 E-mail：public@cdiyue.com Sales In China Tel: 0086-28-85106132 Fax: 0086-28-85189190 E-mail：sales@cdiyue.com International sales Tel: 0086-28-85327536 Fax: 0086-28-85189190 E-mail：wsales@cdiyue.com 27 SZU06C2 PM(Rev 2.
