W ir e le ss Blu e t oot h USB D on gle Use r ’s Gu ide 1
Table of Content CHAPTER 1 INTRODUCTION.................................................................................................. 5 CHAPTER 2 CONTENTS OF PACKAGE................................................................................. 7 CHAPTER 3 INSTALLATION BLUETOOTH SOFTWARE ...................................................... 8 3.1 UNI NSTALLI NG PREVI OUS VERSI ON 3.2 I NSTALLI NG THE BLUETOOTH OF BLUETOOTH SOFTWARE SOFTWARE...............................
7.5.2 Bluetooth Serial Port .............................................................................................. 48 7.5.3 Dial-up Networking Service ................................................................................... 49 7.5.4 Fax Service ............................................................................................................ 50 7.5.5 File Transfer Service.............................................................................................. 51 7.5.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Ch a pt e r 1 I n t r odu ct ion INTRODUCTION TO BLUETOOTH The term “Bluetooth” refers to a worldwide standard for the wireless exchange of data between two devices. In order to exchange data, two Bluetooth devices must establish a connection. Before a connection is established, one device must request a connection with another. The second device accepts (or rejects) the connection. The originator of the request is known as the client. The device that accepts (or rejects) the request is known as the server.
environment. The PC configured as the Bluetooth server can support up to 7 Bluetooth client devices with IP addresses automatically assigned when they connect. The bundled Bluetooth Software also provides Internet sharing and security access between the server and clients. After finishing these steps outlined in this manual, you will have the ability to share information, Network Access and take the full advantage of a “connected” environment.
Ch a pt e r 2 Con t e n t s of Pa ck a ge After opening the box, check what’s in the box, and then refer to the Quick Installation Guide for the fastest way to get up and running with the wireless Bluetooth USB Dongle.
Ch a pt e r 3 I n st a llin g Blu e t oot h Soft w a r e 3 .1 Un in st a llin g pr e viou s ve r sion of Blu e t oot h soft w a r e If you are installing the Bluetooth software for the first time, please skip this section. Any previous versions of the Bluetooth software must be uninstalled before installing an upgraded version. Note: Before start to uninstall the previous version of BTW software, please unplug the wireless Bluetooth Dongle from computer’s USB port first.
4)Click on the Remove button from “Remove the Program” screen. 5) When the files have been removed, you will be presented with a screen informing of its completion. Click on the Finish button.
6). Click on the Yes button to reboot your PC. You have completely uninstalled the previous version of the Bluetooth software. You may go further to install the upgrade version as described in the following section. 3 .2 I n st a llin g t h e Blu e t oot h soft w a r e ( Fir st - t im e in st a lla t ion ) Note: Plug in the USB Dongle firmly to an available USB port only when you are prompted during the installation process.
If you have connected the Bluetooth Dongle to your computer, please remove it, cancel any hardware wizard that may show up, and start here. 1) Close any open programs and insert the utility CD into your CD-ROM Drive. The Autorun function will automatically guide you to start the software installation. (If the Autorun function does not automatically start, please open the Installation CD to find the Setup.exe file and double click the Setup.exe icon to continue.
4) In the Device Information screen: (The screen won’t be displayed if you re-installed the BTW software.) a. Enter a device name b. Select a device type c. Click on the Next button. 5) In the Destination Folder screen you are asked to confirm the Destination Folder for the application software.
another location as the directory. 6) The Ready to Install the Program screen informs you that the driver is ready for installation. Click on the Install button to continue. a. For Windows 2000 & XP users, please click on OK button from the following “Driver Signature Notice” dialog box to proceed with drive installation.
b. Windows 98 Users, you will be asked to specify the directory of Windows 98 source files path during installation. Please enter the location of the Windows98 setup files and follow the on-screen description. 7) Plug the Bluetooth Dongle to an available USB port firmly and click OK to continue with software installation.
8) When the files have been copied, you will be presented with a screen informing of its completion. Click on Finish button to finish the installation process. 9). Click on Yes button to reboot your PC. 3.3 Start Using Bluetooth After you have the Bluetooth software installed and reboot your PC for the first time, please right-click on the Bluetooth icon on the system tray and highlight Starting Using Bluetooth. The wizard to will help you quickly configure your Bluetooth Dongle step by step.
Steps Check the box if you want to access the Bluetooth Software from the three options. Click Next. Input your computer’s name and select its type. Click Next. Click Next button will guide you to make the Bluetooth services of your computer available to other Bluetooth devices. If you click Skip, and then you can configure these Bluetooth Services later via Bluetooth Configuration Panel.
Decide which Bluetooth service that your computer will offer and check the box of it to enable it. You can also click Configure button to modify each service’s property.
Click Finish button to complete the basic Bluetooth configuration. If you want to re-configure the Bluetooth services, you can right-click the Bluetooth icon on the system tray and highlight Bluetooth Setup Wizard.
Ch a pt e r 4 Se t u p D ia gn ost ics 4.1 Hardware Diagram The Bluetooth USB Dongle is plug-and-play. During the software installation process, you will be prompted to plug in the USB dongle to an available USB port. When you plug in the USB Dongle to the USB port, the red Rx LED and the green Tx LED on the USB dongle should light up. See the diagram below. The Bluetooth Dongle LEDs illuminate during connection or data transfer to indicate that the dongle is functioning. Refer to the following table.
The Bluetooth Configuration window will be displayed. Click the Hardware tab. Please refer to the following picture and check if the Device Status field reports “The device is working properly.” and the “Device Address” is correctly displayed. If yes, it means that the Bluetooth dongle drivers and software have been installed successfully.
Ch a pt e r 5 I n t r odu ct ion To Blu e t oot h Soft w a r e The wireless Bluetooth USB Dongle is bundled with Widcomm Bluetooth Software as the management software. The Bluetooth Software is the solution for the seamless integration of Bluetooth technology into personal computers. The software provides the user an easy interface to manage the Bluetooth Dongle. 5.
5.2 BLUETOOTH DEVICE IDENTITY Every Bluetooth device has a unique 48-bit binary Bluetooth Device Address (BDA) burned into its EEPROM. This address cannot be changed by the end-user. A device’s BDA is usually displayed in hexadecimal format; 00:D0:B7:03:2E:9F is a valid BDA. You can find the BDA from the Bluetooth Configuration Panel -> Hardware tab -> Device Address. Each Bluetooth device also has an operator-configurable, user-friendly name to help distinguish it from other Bluetooth devices.
Access the Bluetooth Configuration Panel—right-click the Bluetooth icon, and then select Advanced Configuration. Access the Quick Connect option—right-click the Bluetooth icon, select Quick Connect, and then select the type of service to which you wish to connect. Start/Stop Bluetooth on this computer. 5.4 ACCESS MY BLUETOOTH PLACES My Bluetooth Places is part of Windows Explorer.
Enabled Disabled Connected Blue with White Blue with Red Blue with Green Figure 1: Bluetooth Icon Bluetooth Icon Indicates Bluetooth Status Figure 2: Device Icons for Windows 9x, Me and 2K 24
Figure 3: Service Icons for Windows 9x, Me and 2K Service Icons for Windows 9x, Me and 2K Note: Services may be unavailable because they are in use or because the necessary hardware is not installed.
Figure 4: Device Icons for Windows XPDevice Ions for Windows Figure 5: Service Icons for Windows XP 26
NOTE: Services may be unavailable because they are in use or because the necessary hardware is not installed.
Ch a pt e r 6 Ba sic Ope r a t ion s 6.1 START OR STOP BLUETOOTH To start Bluetooth: In the Windows system tray, right-click the Bluetooth icon and select “Start the Bluetooth Device”. The Bluetooth icon is blue in color with a white insert when Bluetooth is running. To stop Bluetooth: In the Windows system tray, right-click the Bluetooth icon and select “Stop the Bluetooth Device”. . The Bluetooth icon is blue in color with a red insert when Bluetooth is stopped. 6.
If this computer has created a connection to the desired type of service in the past, the options on the shortcut menu are: The name(s) of any device(s) with which prior connections to this type of service have been established. Select a name from the list to re-establish connection. Other Devices …Select this option to search for additional devices that potentially provide the desired service, select a device from the list, and then click Connect.
You can click the radio button of each item and follow the wizard's on-screen instructions. 6.4 CREATE A CONNECTION FROM BLUETOOTH EXPLORER From Bluetooth Explorer Right-click a device name and select “Connect to…” the desired service.
or In the Folders pane, select a device, and then, in the right pane, right-click a service provided by that device and select “Connect.” NOTE: Only available services are displayed in the menus.
6.5 FIND BLUETOOTH DEVICES Search for Devices looks for Bluetooth devices in the vicinity and displays the devices that it finds in My Bluetooth Places. To start a search for devices, in the Folders pane of My Bluetooth Places, select Entire Bluetooth Neighborhood, and then, from the Bluetooth menu, select Search for Devices. NOTE: The Bluetooth menu is only visible when My Bluetooth Places is active. 6.5.
From the Bluetooth Configuration screen, click “Discovery” Tab. Check the box of “Look for other Bluetooth devices” and input the interval. Some devices within connection range may not show up in the list of devices found because: Your device is configured to report only specific types or classes of devices (Bluetooth Configuration Panel > Discovery tab, on your device). The unlisted device is configured to be non-discoverable (Bluetooth Configuration Panel > Accessibility tab, on the un-listed device).
Discovery. To initiate a Service Discovery, in the Folders pane of My Bluetooth Places, right-click a device name and select Discover Available Services from the shortcut menu. Bluetooth services are those things that this computer can do for remote Bluetooth devices. For example, if this computer allows a remote Bluetooth device to send a fax using a fax modem that is physically attached to this computer, then this computer is providing the Bluetooth fax service.
connected the devices. Dial-up Networking—allows a device to use a modem that is physically attached to another Bluetooth device. Fax—allows a device to send a fax using a remote Bluetooth cell phone, modem, or computer. File Transfer—allows a device to perform file system operations on another Bluetooth device; browse, open, copy, etc. Headset—allows a Bluetooth headset to be used as the audio input/output mechanism for another Bluetooth device, such as a computer or cell phone.
The Information provided is: Status: “Connected” or “Not Connected” Device Name: the name of the device to which this computer is connected. Duration: the length of time that this connection has been established, displayed in hours, minutes and seconds.
time out (automatically disconnect) after a specific period of inactivity. Activity: the number of bytes sent and received over the connection. Signal Strength: a graphic indicator that ranges from Too Weak through Good to Too Strong. NOTE: To change the power transmission level of this computer: from the Bluetooth Configuration Panel, Hardware tab, click the Advanced button, and then change the setting in the Maximum Power Transmission drop-down list. The Advanced button is not available in all countries.
b) Microsoft Office—only the document in the active window can be transferred. c) Microsoft Outlook—select one or more items to be transferred. 2. From the application's File menu, select Send To, and then select Bluetooth from the shortcut menu. 3. Select a device from the shortcut menu to send the data or Select Other..., choose a device from the list, and then click OK to send the data.
Ch a pt e r 7 Con figu r a t ion Pa n e l 7.1 ACCESS THE BLUETOOTH CONFIGURATION PANEL The Bluetooth Configuration Panel provides access to settings for Bluetooth services, client applications, hardware, security, discovery, accessibility, default paths, event notification and other Bluetooth related items. To Open the Bluetooth Configuration Panel From the Windows Control Panel, select Bluetooth Configuration.
7.2 GENERAL CONFIGURATION SETTINGS The settings on the General tab of the Bluetooth Configuration Panel determine information that is displayed to remote devices. Identity Computer Name-enter a unique name to identify this computer to other Bluetooth devices in the vicinity; this field cannot be left blank. Computer type-select either Desktop or Laptop from the shortcut menu to set the type of icon remote devices will use to represent this computer.
7.3 ACCESSIBILITY SETTINGS The Accessibility tab of the Bluetooth Configuration Panel lets you specify whether remote devices may access this computer, which remote devices have access, and whether an audio warning is played when a Personal Identification Number (PIN code) is required. Allow other devices to discover this computer Select “Let other Bluetooth devices discover this computer” to permit remote Bluetooth devices to find and report this computer.
Only paired devices—only devices that have been paired with this computer are allowed to connect to it. Only devices listed below—only the listed devices are allowed to connect to this computer (see Accessibility, adding and deleting devices). Choose an audio notification file When Secure Connection is enabled for any of the Bluetooth Services on this computer a PIN code is required before that service can be accessed.
NOTE: Multiple devices may be selected using SHIFT + click and/or CTRL + click. Delete a device from the list In the list of devices allowed to access this computer, select the device to be removed from the list, and then click Delete.
7.4 DISCOVERY SETTINGS The settings on the Discovery tab of the Bluetooth Configuration Panel determine whether this computer looks for other Bluetooth devices automatically, how often it looks and what type of devices it looks for. Periodic Search for Devices When “Look for other Bluetooth devices” is selected, Bluetooth automatically searches for devices every X minutes. X is an whole number between 1 and 60. To change the time between auto inquiries, highlight the existing time and enter the new time.
and Discovery, Deleting Specific Devices). Discover Specific Devices The type of device(s) that this computer looks for and reports when it is searching for other Bluetooth devices can be limited. Limit the remote devices reported Bluetooth can report only specific devices, specific class(es) of device(s), or specific type(s) of device(s) within a class. Specific devices: an individual computer or Bluetooth cellular telephone are examples of specific devices.
7.5 BLUETOOTH LOCAL SERVICES Common Configuration Settings The settings on the Local Services tab of the Bluetooth Configuration Panel determine the configuration of the services provided by your computer to remote devices. Each service can be configured individually for security, name, and other settings. The Local Services tab also includes options to add and delete user-defined serial services. These properties can be set individually for each Bluetooth service.
• Dial-Up Networking • Fax • File Transfer • PIM Item Transfer • PIM Synchronization • Network Access 7.5.1 Audio Gateway The Bluetooth Audio Gateway service allows this computer to use a remote Bluetooth device’s microphone and speakers as this computer’s input and output devices. For example, if this computer has voice recognition capabilities, a Bluetooth headset might be used as the audio input device.
Set the common configuration properties of the service from General and Notification Tabs, and then click OK. 7.5.2 Bluetooth Serial Port The Bluetooth Serial Port service allows a remote Bluetooth device to establish a wireless serial connection with this computer. The wireless serial connection may be used by applications as though a physical serial cable connected the devices.
2. In the properties dialog box, modify the properties: Enter a unique name (less than 99 alphanumeric characters). Select secure connection, if desired. Select Startup Automatically, if desired From the COM Port shortcut menu select a communications port that is not assigned to any other service. 3. Click OK. To remove a Bluetooth Serial Port From the Bluetooth Configuration Panel, Local Services tab, select the port to be removed and then click Delete.
From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the Dial-up Networking service. Select the physical modem to be used from the Modems: drop-down menu. Set the common configuration properties of the service, and then click OK. 7.5.4 Fax Service The Fax service allows a remote Bluetooth device to send a Fax via a modem that is physically attached to this computer.
Select the physical modem to be used from the Modems: drop-down menu. Set the common configuration properties of the service, and then click OK. 7.5.5 File Transfer Service Configure the File Transfer Service From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the File Transfer Service.
Bluetooth exchange folder location: the directory configured in this section is the highest-level directory to which a remote Bluetooth computer has access. This directory and its sub directories are displayed in the remote device's My Bluetooth Places. NOTE: The Bluetooth Exchange Folder is shared by the PIM Item Transfer and the File Transfer services and can be configured from the Properties page of either of those services.
Copy to/from a remote device In the Folders pane of Explorer, from the Entire Bluetooth Neighborhood branch, select a device and expand that branch to view the Bluetooth Exchange Folder of the remote device. NOTE: “Public Folder” is not available, the remote device is not configured to allow remote file operations. Use drag-and-drop to copy any file or folder contained in the Public Folder of the remote device to the desired folder on this computer.
Hardware Requirements This computer must have a sound card, microphone, and speakers installed. The Bluetooth radio on both on this computer and the remote device must support audio. Configure the Headset Service From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the Headset service. Set the common configuration properties of the service, and then click OK. 7.5.
7.5.7.1 Setup for Windows 2000 and Windows XP Steps From the Windows system tray, right-click the Bluetooth icon and select Advanced Configuration from the shortcut menu. In the Bluetooth configuration panel, select the Local Services tab, Network Access and then click Properties.... From the Network Access, General properties page, in the Type of service shortcut menu, select “Allow other devices to access the Internet/LAN via this computer,” and then click Configure Connection Sharing.
Windows ME: If the Bluetooth sever is running in Windows 98SE or Windows ME, you have to install an Internet Protocol Routing software. There are lots of trial versions of Internet Protocol Routing software in the Internet. For example: A downloadable trail version of Sygate Home Network is available on the Sygate Technologies Inc. The website is http://www.sygate.com/. Installing and configuring the Sygate Home Network : Please follow the on-screen descriptions to install the Sygate Home Network.
In the right panel of the Configuration screen, check the radio button Select manually from Local Network connections and select the 0000:Bluetooth PAN Driver. Be sure to check the Enable Address Server (DHCP) from the Options item. On the left side of the Configuration screen, check the radio button of Ethernet and select the LAN card the PC is using. Now, you have successfully configured your PC or laptop to the Bluetooth server.
Share a printer. From Windows Start menu -> Settings -> Printers, right-click the printer icon you want to share and select Sharing from the shortcut menu. Click the Sharing tab from the Printer Properties dialog box and click the radio button of “Shared as” to share this printer. Enable Guest Account. Right-click “My computer” icon on your desktop and select “Manage”. From the “Computer Management” window, click the + icon in front of “Local Users and Groups” to extend sub-menus.
Click Next to find the printer. Select the Bluetooth server, select the shared printer and click Next.
Click Finish button to complete the installation. 7.5.8 PIM Item Transfer Overview The PIM Item Transfer service allows Personal Information Manager items to be transferred between this computer and a remote Bluetooth device. Four data types are supported: Business Cards Calendar Items Email Messages Notes Each data type can be saved in any of the supported and installed PIMs. NOTE: PIMs which are not installed on this computer will not appear in the shortcut menus.
Configure From the Windows system tray, right-click the Bluetooth icon and select Advanced Configuration from the shortcut menu. In the Bluetooth configuration panel, select the Local Services tab, and double click PIM Item Transfer. In addition to the configuration options common to all Bluetooth services, this service also has settings that determine: How business card requests are handled.
send the same business card” option, above, that card will be added to the shortcut menu as an option. NOTE: Previously sent business card additions to the menu are limited to ten, after which the oldest contact will be replaced. Where to store inbound data items, on an individual basis.
open this shortcut menu and select a new PIM. NOTE: A new default business card must be selected from the database of the newly selected PIM. Choose a default business card 1. In the Select a Bluetooth Business Card dialog box that appears when “Always send the same business card” is selected, highlight the card. NOTE: Once a card is highlighted, if you “hover” the mouse pointer over that selection, a balloon appears with additional information about that contact. 2.
Services tab, and double click PIM Synchronization. Whether an individual item is accepted and where it is stored, when accepted, is configured in the PIM Item Transfer service. If that service is not configured to store a particular data type in Outlook, then that data type cannot be synchronized.
7.5.10 NOTIFICATION Overview There are three types of notification: Authentication request, also called a PIN code request — this notification appears automatically in a balloon over the Windows system tray if a Personal Identification Code is required before a connection can proceed. An audio file can also be associated with the notification. Authorization request, also called a connection request—this type of notification can be visual, audio, or both.
Connection notification (step 3, above) only happens if it has been enabled on the Notifications tab of the individual service being accessed. Service Access Notification “Notifications” lets you associate a sound (Windows *.wav file) and/or a visual indication with access attempts by remote devices. A different notification sound can be associated with each local Bluetooth service. Associate a sound with service access From the Bluetooth Configuration Panel, Local Services tab: 1.
7.6 BLUETOOTH CLIENT APPLICATIONS Overview Some built-in Bluetooth applications provide full functionality for a specific task, such as locating other Bluetooth devices or synchronizing two Personal Information Managers. Other built-in Bluetooth applications provide a way for standard Windows applications to accomplish their tasks wirelessly. For example, a Bluetooth application may create a wireless serial connection between computers or provide wireless access to the Internet.
7.6.
• The application name—to change it, highlight the existing name and enter the new name. • Enable or disable secure connection. To enable secure connection, place a checkmark in the box. Close an audio gateway connection If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Audio Gateway and then select the device that is providing the service (active connections have a checkmark in front of them).
Configure The Bluetooth Configuration Panel > Client Applications > Bluetooth Serial Port > General tab provides options to configure: The application name—to change it, highlight the existing name and enter the new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. The communications port (COM port) to be used. NOTE: Unless you have a specific reason to do so, DO NOT CHANGE the default COM Port setting.
7.6.3 Dial-up Networking Overview The Bluetooth Dial-up Networking application allows this computer to use a modem that is physically connected to a remote device to access the Internet, log on to a remote network.
The Bluetooth virtual device to be used. NOTE: Unless you have a specific reason to do so, DO NOT CHANGE the default Bluetooth device or alter the device's configuration. Close a Dial-up Networking connection If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Dial-up Networking and then select the device that is providing the service (active connections have a checkmark in front of them).
The application name—to change it, highlight the existing name and enter the new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. Close a Fax Connection Fax connections close automatically when the Fax transmission is complete. 7.6.5 Headset Overview The Headset application allows this computer to use a Bluetooth headset (or any other device that offers the Bluetooth headset service) as the audio input and output device for this computer.
Create a Headset connection Establish a connection using one of these techniques: Windows system tray, Bluetooth icon From Bluetooth Explorer Using the Bluetooth Setup Wizard NOTE: Most Bluetooth headsets “ring” when a connection is attempted; answer the ring to complete the connection and begin using the headset as the audio input/output device for this computer.
new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. 7.6.6 File Transfer Overview The Bluetooth File Transfer application allows this computer to perform file operations on the Bluetooth Exchange Folder (and the folders and files it contains) of a remote device.
its sub-folders) of the remote device. Other file operations Right-click a file or folder in the remote device’s Public Folder for a context sensitive menu. All potential menu options may not be available at all times. Potential menu options include: Open—opens the selected file on this computer, using the default application for this type of file. Print—sends the selected file to this computer’s default printer.
new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. 7.6.7 Network Access Overview The Bluetooth Network Access application makes it possible for this computer: To connect to a Local Area Network via a physical connection on a remote Bluetooth device. or To connect to an ad hoc network provided by a remote Bluetooth device. The type of network connection that is available is determined by the configuration of the remote Bluetooth device.
The application name—to change it, highlight the existing name and enter the new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. 7.6.8 PIM Synchronization Overview The PIM Synchronization Application is used to synchronize the Personal Information Manager (PIM) database of this computer with the PIM database of a remote Bluetooth device. The supported PIMs are: Microsoft Outlook Microsoft Outlook Express Lotus Notes.
Configure PIM Synchronization The Bluetooth Configuration Panel > Client Applications > PIM Synchronization > General tab provides options to configure: The application name—to change it, highlight the existing name and enter the new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. The PIM items to be synchronized and the PIM on this computer with which those items should be synced.
Possible synchronization options for each of these data item types include: Do Not Synchronize-this item type will not be synchronized. Synchronize Microsoft Outlook-this item type will be synced with its matching entry in Microsoft Outlook, regardless of the PIM that contains this entry on the remote device. If a matching Outlook entry does not exist, it will be created.
2. From Windows Explorer, My Bluetooth Places, highlight the PIM Item Transfer service on a remote device, and then, from the Bluetooth menu on the Windows menu bar, select the appropriate action. In addition to the business card options listed above, you can also send Notes (*.vnt), Email (*.vmg) and Calendar (*.vcs) items from this menu. 3. From within a supported Personal Information Manager, select one or more items and then, from the PIM's File menu, select Send to Bluetooth.
device will receive a timeout notice. Always send the same business card - when this option is selected a dialog appears that allows you to set a default business card, which will be sent automatically when requests are received. Where to store received business cards. The Received Business Cards options are: Microsoft Outlook Outlook Express Lotus Notes NOTE: The selected Received Business Cards option does not influence the settings on other PIM-related property pages.
The application name—to change it, highlight the existing name and enter the new name. Enable or disable secure connection. To enable secure connection, place a checkmark in the box. Install a Bluetooth Printer Option One: 1. Perform a search for devices and then, from Entire Bluetooth Neighborhood, right-click a Bluetooth printer, select Add Printer from the shortcut menu and follow the on-screen instructions. 2. When the wizard asks you to select a printer make and model, do so.
3. On the next screen, select the printer by name, and then click Connect. 4. Install the driver: when asked to select a printer make and model, do so. If your printer is not in the list of options, click Have Disk…, insert the driver disk for the printer, and then navigate to the drive and directory that contain the driver initiation file (*.inf) for the printer. 5. To complete the installation, follow the on-screen instructions.
Device Properties: Device status: indicates that the device is operating properly or that there is a problem/conflict. Manufacturer: the name of the company that manufactured the device selected in the Devices section of this dialog box. Firmware Revision: the manufacturer's firmware version number. Device Address: the Bluetooth Device Address (BDA or BD_Addr) assigned to this device when it was manufactured.
Click Yes to reset the Bluetooth device now—all open Bluetooth connections will be closed. Click No to save the changes—the changes will be applied the next time the Bluetooth device is reset or restarted.
Ch a pt e r 8 Se cu r it y 8.1 AUTHENTICATION Authentication is used to verify identity; it requires a passkey or link key from the remote device. When a remote device attempts access, a visual and/or audio warning notifies the local operator. If the notification is ignored, access is denied after a preset timeout. When devices are “paired,” those devices automatically exchange a Link Key and Authentication is carried out without operator intervention. 8.
connect. You can initiate the pairing from your own PC or accept a request for pairing from the other device. NOTE: The mate of a pair always appears in My Bluetooth Places, even if the mate is not turned on or is out of connection range. Paired devices remain paired even when One of the devices is not on A service connection is interrupted or the service stopped One or both devices are rebooted.
Meanwhile, there will be a bubble message shown on the remote device’s system tray to indicate you to enter the PIN code. Click this bubble message. Enter the PIN code. The Bluetooth PIN code should be the same between paired devices. Remove Pairing In the Folders pane of My Bluetooth Places, right-click a paired device and select Unpair Device from the shortcut menu.
8.6 PASSKEY An alphanumeric string up to 16 characters in length. Passkeys are also called Personal Identification Numbers, or PIN codes. A passkey may be required if the Secure Connection option is enabled for a Bluetooth service or application. 8.7 SECURE CONNECTION A passkey or link key is required each time a connection is attempted. All data exchanged over the Bluetooth connection is encrypted. Depending on other configuration options, authorization may also be required. 8.
Ch a pt e r 9 Tr ou ble sh oot in g CANNOT CONNECT TO A PAIRED DEVICE Paired devices are always displayed in My Bluetooth Places, even if the remote device is out of range or not powered up. Verify that the remote member of the pair is within radio range, and powered up, and then attempt the connection again. CANNOT DISCOVER SERVICES ON AN UN-PAIRED REMOTE DEVICE The remote device may not be powered up or may be out of range. Verify that the remote device is powered up.
(HCI) In the Bluetooth Configuration Panel, on the Hardware tab, in the Device Properties section, the fifth entry provides Bluetooth Specification compliance information for the Host Controller Interface. The sixth entry contains the Specification Revision information for the Host Controller Interface, if appropriate.
Upgrade to a newer version of Windows Use an m3u-to-mp3 conversion utility to convert the file(s) into a format that is supported by Windows 98. (Conversion utilities are available as freeware or shareware on the Internet.
