Datasheet

ManualsBrandsChemtronics ManualsDesolderingDesoldering Braids 1.5 m 1.5 mm Yellow

Soder-Wick(R) No Clean Desoldering Braid

IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE

COMPANY/UNDERTAKING

Chemtrec - 1-800-424-9300 or collect 703-527-3887

SAFETY DATA SHEET

Product name

Soder-Wick(R) No Clean Desoldering Braid

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Europe

Emergency telephone number

(with hours of operation)

Chemical name

No Clean flux coated, braided copper wire

Soder-Wick(R) No Cleain, Soder-Wick No Clean(R) SD, Soder-Wick(R) No Clean

BGA. Various codes based on size and length, including but not limited to:

SW16015, SW16025, SW16035, SW16045, SW16055, 60-BGA-5, 60-1-10, 60-1-

5, 60-2-10, 60-2-5, 60-3-10, 60-3-5, 60-4-10, 60-4-5, 60-5-10, 60-5-5, 60-6-5

Synonyms

ITW Chemtronics

8125 Cobb Center Drive

Kennesaw, GA 30152

Tel. 770-424-4888 or toll free 800-645-5244

Manufacturer

Distributor

Use of the substance/mixture

Desoldering

Identification of the substance or mixture

Company/undertaking identification

ITW Contamination Control BV

Saffierlaan 5

VZ-2132 Hoofddorp

The Netherlands

Tel: +31 88 1307 400

FAX: +31 88 1307 499

Importer

Solid.

Product type

e-mail address of person

responsible for this SDS

askchemtronics@chemtronics.com

HAZARDS IDENTIFICATION

Classification

R42/43

The product is classified as dangerous according to Directive 1999/45/EC and its amendments.

Physical/chemical hazards

FUMES MAY BE HARMFUL May be harmful by inhalation after often repeated

exposure.Slightly hazardous by the following route of exposure:Skin contact irritant

Human health hazards

Caution: exposure to this material may cause certain sensitive individuals to develop

eczema and/or asthma. May cause sensitisation by inhalation and skin contact.

Sensitised persons may subsequently show asthmatic symptoms when exposed to

atmospheric concentrations well below the OEL.

Additional hazards

May cause allergic reactions in certain individuals.

See Section 11 for more detailed information on health effects and symptoms.

COMPOSITION/INFORMATION ON INGREDIENTS

copper

7440-50-8

90 - 99

231-159-6

N; R50

[1] [2]

rosin

73138-82-6

1 - 3

277-299-1

R43

[1]

Substance/preparation

Mixture

Occupational exposure limits, if available, are listed in Section 8.

CAS

number

EC number

Classification

Ingredient name

See Section 16 for the full text of the R-phrases

declared above.

[1] Substance classified with a health or environmental hazard

[2] Substance with a workplace exposure limit

There are no additional ingredients present which, within the current knowledge of the supplier and in the

concentrations applicable, are classified as hazardous to health or the environment and hence require reporting

in this section.

First-aid measures

FIRST AID MEASURES

Date of issue/Date of

revision

7/5/2011.

1/7

Summary of content (7 pages)

PAGE 1
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Europe SAFETY DATA SHEET Soder-Wick(R) No Clean Desoldering Braid 1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING Identification of the substance or mixture Product name : Soder-Wick(R) No Clean Desoldering Braid Chemical name Synonyms : No Clean flux coated, braided copper wire : Soder-Wick(R) No Cleain, Soder-Wick No Clean(R) SD, Soder-Wick(R) No Clean BGA.
PAGE 2
Soder-Wick(R) No Clean Desoldering Braid 4. FIRST AID MEASURES Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe.
PAGE 3
Soder-Wick(R) No Clean Desoldering Braid 7. HANDLING AND STORAGE Handling : Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas.
PAGE 4
Soder-Wick(R) No Clean Desoldering Braid 10. STABILITY AND REACTIVITY Stability Conditions to avoid Materials to avoid Hazardous decomposition products : : : : The product is stable. No specific data. No specific data. Under normal conditions of storage and use, hazardous decomposition products should not be produced. 11. TOXICOLOGICAL INFORMATION Potential acute health effects Inhalation : May cause respiratory irritation.
PAGE 5
Soder-Wick(R) No Clean Desoldering Braid 12. ECOLOGICAL INFORMATION Date of issue/Date of revision : 7/5/2011. - Acute EC50 18.4 ug/L Fresh water - Acute EC50 16.1 ug/L Fresh water - Acute EC50 14.1 ug/L Fresh water - Acute EC50 9.89 ug/L Fresh water - Acute EC50 9.2 ug/L Fresh water - Acute EC50 9 ug/L Fresh water - Acute EC50 6.5 ug/L Fresh water - Acute EC50 6 to 8 ug/L Fresh water - Acute EC50 4 ug/L Fresh water - Acute EC50 2.8 ug/L Fresh water - Acute EC50 2.
PAGE 6
Soder-Wick(R) No Clean Desoldering Braid 12. ECOLOGICAL INFORMATION - - - - - - - - - - - - Conclusion/Summary Biodegradability Conclusion/Summary Date of issue/Date of revision Acute EC50 2 to 4 ug/L Fresh water Daphnia - Water flea Ceriodaphnia dubia - Neonate <24 hours - 2.5 mm Acute EC50 1.6 Daphnia - Water ug/L Fresh water flea Ceriodaphnia dubia - Neonate <24 hours - 0.25 mm Acute IC50 0.
PAGE 7
Soder-Wick(R) No Clean Desoldering Braid 12. ECOLOGICAL INFORMATION Other adverse effects : No known significant effects or critical hazards. 13. DISPOSAL CONSIDERATIONS Methods of disposal : Avoid contact of spilt material and runoff with soil and surface waterways. Dispose of according to all federal, state and local applicable regulations.Recycle, if possible. Hazardous waste : The classification of the product may meet the criteria for a hazardous waste. 14.