0071753 USER'S MANUAL Title: NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) REVISIONS REV 00 01 02 DESCRIPTION CR2660AB ECN8210 ECN8212 DATE 05/30/18 08/20/20 10/06/20 DOC SPEC REVISIONS ENGINEER S. SINGH S. SINGH S. SINGH REV DESCRIPTION DATE APPROVED DATES DWN CHK ENG Used On APPD Size US Letter Scale: N/A 10071753 Checkpoint Systems, Inc.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) Important Information to our Users in North America FCC Regulatory Compliance Statement Checkpoint Systems, Inc., offers Electronic Article Surveillance (EAS) or Radio Frequency Identification Products that have been FCC certified or verified to 47 CFR Part 15 Subparts B/C.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) Important Information to our Users in Europe CE Regulatory Compliance Statement Where applicable, Checkpoint Systems, Inc. offers certain Electronic Article Surveillance (EAS) products that have CE Declarations of Conformity according to R&TTE Directive 99/5/EC, EMC Directive 2004/108/EC, and Low Voltage Directive 2006/95/EC.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) WEEE Marking All products that are subject to the WEEE Directive supplied by Checkpoint are compliant with the WEEE marking requirements. Such products are marked with the "crossed out wheelie bin" WEEE symbol shown below in accordance with European Standard EN 50419.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) TABLE OF CONTENTS 1.0 2.0 INTRODUCTION ............................................................................................................................. 7 1.1 1.2 System Identification....................................................................................................................7 System Level Checkpoint Part Numbers (SKUs) .........................................................................7 1.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 8.0 7.1 General Details .........................................................................................................................25 7.2 7.3 7.4 PSU 1:1 Rule .............................................................................................................................26 Other Safety Considerations ......................................................................................................
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 1.0 INTRODUCTION The released NEO System Models include NP10, NP20 and NG10. There are various hardware options, all of which are described in this document. The part numbers of each specific model are listed following the photos. 1.1 System Identification Figure 1: NP10 1.2 Figure 2: NP20 Figure 3: NG10 System Level Checkpoint Part Numbers (SKUs) Checkpoint Part Number (CKP P/N) can be considered the SKU of the Finished Good.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) Model Name System SKU Omnify Description NG10 2.7M 10034928 *NG10 PSB WHT 10034982 *NG10 PSB GRY RAL 7024 10034929 *NG10 PSB WHT W/COLES LOGO Table 1-2: RF/HUB Models Model Name System SKU NP10 2.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) Table 1-4: RFID-Enabled NEO Models 1.2.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 2.0 2.1 2.1.1 GENERAL DESCRIPTION EAS Features Radio Frequency Band Detection Limited to 8.2 MHz • No “Application Based Detection Mode” (7.6, 9.0 detection). • NEO is tuned to achieve detection of HF targets at 8.2MHz ±5% radio frequency. • Tags tuned to other frequencies may or may not produce the alarm; expect a noticeable drop in performance for any non 8.2 tag.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 3.0 QUICK CONNECT INTERFACES All NEO Family Antennas are equipped with a technology called "Quick Base" and required Quick Connect Cables. The minimum three (3) cables are DC Power Input, General Purpose Outputs (GPO) (Relay contact pairs) and General Purpose Inputs (Digital Inputs) (GPI). • Base configuration has 3 cables total, and the "with Hub" antennas have 4 cables. • The number of cables needed will vary per system, per site.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 4.0 4.1 SYSTEM HARDWARE System Controller Excluding SAB Antennas, every NEO includes one (1) EAS Sensor and antenna wiring, and one (1) System Controller and control cabling. The System Controller is one of the central devices. USB devices and the Light and Speaker board interface directly with it. A 64-Bit Processor runs the embedded software and firmware, which work together to control all high-level and low-level operations.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 4.2.2 LED Board The LED Board has 10 LEDs which are each comprised of 3 RGB LEDs, 3 sub-LEDs per every 1 Multicolor LED. The LED Board also has a small momentary switch, which is a push button; only Field Service is expected to use this interface. 4.2.3 Speaker NEO features an audio speaker, which is distinctly different from a piezo type "buzzer". Read more about the Speaker in section 5.6. 4.2.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) ensures tightness. Connectors are also "dressed" or pre-installed at the time of manufacture. The TR4300 board is mounted in a subassembly referred to as the "Cage" or sometimes "Board Carrier" (also "PCBA" for PCB Assembly). The entire cage is the spare. See Table 4-2 for the spare or upgrade part numbers (SAP Material code).
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) There is no BUZZER I/O on the NEO Splitter board. Note that both PAB and SAB systems also contain one "Coupler board" (impedance matching board). The diagram below shows the 8.2 MHz RF signal path (other cabling and hardware features not depicted), showing how TX1 and TX2 are used in this scenario: Figure 9: PAB (above left) and SAB (above right): Hardware in each pedestal, RF signal routing 4.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 4.6 RFID Reader The NEO "Fast Track" RFID Reader (CKP P/N 10079516) is installed in NEO RF/RFID Dual system. These are not officially released but can be considered released for beta installation (i.e. the hardware can be installed for test; beta systems are always labeled "Not for sale"). The RFID Reader is part of the Lower Bay "Cage" assembly.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 24V Power Input Inside NEO: +24V = White Cable (this pole of the Orange Connector has the Black stripe) NEO side GND GND +24V DC +24V DC From PSU The power connection is a "tool less" connector (only wire strippers/cutters are needed to prep the wire leads, no screw driver is required).
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 5.0 5.1 SPECIFICATIONS Overall Size NP10: Height: 172.78cm [68.02in] Width: 50.75cm [19.98in] Depth (front to back): 7.62cm [3.00in] NP20: Height: 172.78cm [68.02in] Width: 34.26cm [13.49in] Depth (front to back): 7.62cm [3.00in] NG10: Height: 174.7 [68.78in] Width: 50.76cm [19.98in] Depth (front to back): 7.72cm [3.04in] 5.2 EAS Sensor Mechanical Specs: PCB Layers: 8 PCB Materials: FR4 Dimensions: L X W: 116mm X 170mm [4.567in X 6.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) USB Serial port (1): USB Type B connector, shielded IO Board (GPIO module) B2B connector (1): 2 x 12 Header PCB-mount, Right Angle Expansion (e.g. Hub board) B2B connector (1): 2 x 12 Header PCB-mount, Right Angle 5.3 PAB/SAB Splitter Board The A1207 PAB/SAB Splitter Board (CKP P/N 10034597) is only featured on select models. For a list of PAB/SAB Models, see Table 1-3 from Section 1.2.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 5.4 System Controller Mechanical Specs: Small PCB about the size of a credit card Electrical Specs: CPU: 64-Bit Processor Memory: 1GB 1600MHz LPDDR3 memory; 16GB Connector function (Number): Connector type Data Interface to/ from LnS Board (1): Header 2 x 20 PCB mounted, Female socket Power input: DC power supplied from the Light and Speaker board (thru 2 x 20 header pins) USB serial interface: USB Type A ports (3).
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) LED 7-Pin mini jack (1): Hirose 7-Pin port, keyed System Controller Audio Input 3-Pin mini jack (1) Hirose 3-Pin port, keyed USB Connector (1): USB Mini-C connector for interface to controller 5.6 IO Board (GPIO Module) Mechanical Specs: PCB Layers: 4 PCB Materials: FR4 Dimensions: 32.5mm X 76.5mm [1.28in X 3.01in] Electrical Specs: Inputs: 4. RJ-45 connector (2 pins per input). Outputs: 2. The GPO RJ-45 connector has 4 relay contact pairs in total.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 5.8 LED Board Mechanical specs: PCB Layers: 2 PCB Materials: FR4 Dimensions:NP10 - 319.5mm X 12mm [12.58in X 0.47in] NP20 - 156.0mm X 12mm [6.14in X 0.47in] Features: 10 LEDs aligned in a row. Each LED can illuminate in various colors, relying on 3 individual LEDs (Red, Green, and Blue) inside each of the 10 PCB-mounted LEDs. Electrical specs: Connector port (1): 7-Pin Hirose connector NP10 / NG10 contains: ^PCB,A1179 LED NP10 (10055944).
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 5.10 RFID Reader Mechanical specs: PCB Layers: 8 PCB Materials: FR4 Dimensions: 225.2mm x 170mm (approximate outside dimensions) [8.87 x 6.69in] Electrical Specs: DC Power Input: +12V DC Regulated Outputs: N/A RF (UHF) Antenna Outputs: 4 SMA Female Other Connector Types: RJ-45 (1), RS-232 Serial port for "Service". B2B connector (1): 2 x 8 Header PCB-mount (from Hub Board) 5.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 6.0 USING DMS TO APPLY SOFTWARE SETTINGS Checkpoint DMS is by-license-only software, which will be used by field service, engineering and manufacturing to set up NEO. Tuning can be performed using DMS. Transmit Power and other critical settings are checked/set with the help of Analog View and similar software features. DMS is also used at the time System installation to pick the LED color, pattern and the sound file (.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 7.0 POWER SUPPLY REQUIREMENTS 7.1 General Details The Power Supply Unit (PSU) is sold separately from NEO. NEO requires +24 Volts DC supplied at J6 or J14 of the EAS Sensor. PSU which is suitable shall be an external AC/DC converter power supply rated at 24VDC nominal, with LPS either 50W or 90W maximum. LPS stands for limited power source. Refer to Sourcing Spec (CKP P/N 10034493). 7.1.1 Approved PSU Model Use only the approved power supply.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 7.1.2 Plenum PSU Installation In the US, if the power supply is to be installed in a plenum (HVAC ventilation) area, the GlobTek GS-599MC-KIT(R) (CKP P/N 7367100) must be installed. In the event of such an installation, the power supply must be hard wired to comply with section 300.22 (C) of the NEC. The kit includes the standard power supply (see Figure 10 above) and plenum-rated conversion kit. 7.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) The NEO Install Kit contains additional ferrite core, which can be applied to the Power Supply at the AC/DC Adapter side on the DC cable (see below). The ferrite at the power supply side is optional. 7.4.2 Optional Ferrite on DC Cord near PSU AC/DC Adapter Although not required for FCC or ETSI compliance, the ferrite core shown below is considered "optional.
USER'S MANUAL, NP10, NP20, NG10 (ALL NEO SYSTEM MODELS) 8.0 8.1 DEVICE LABELING Internal Label Each NEO will have a label, found in the base region, which indicates this specific unit’s Model Name, part number, revision and the serial number of the unit manufactured, as well as regulatory information. For example: Cellular: FCC ID: DO4NEO-C WiFi: FCC ID: DO4NEO Device agency label will also show country/region specific markings, indicating approval is obtained in that region.
