User Manual
TABLE OF CONTENTS 1. Before You Begin ........................................................................................................... 3 What Is Included ........................................................................................................................... 3 Unpacking Instructions ................................................................................................................. 3 Claims ...........................................................................
1. BEFORE YOU BEGIN What Is Included • • Intimidator™ Scan LED 300 Hanging Bracket with Mounting Hardware (preinstalled) • • • Power Cord Warranty Card Quick Reference Guide Unpacking Instructions Immediately upon receipt, carefully unpack the product and check the container to make sure you have received all the parts indicated above in good condition.
Product at a Glance Use on Dimmer Outdoor Use Sound-Activated DMX Master/Slave Safety Notes Auto Programs Switchable voltage (120 V/230 V) Replaceable Fuse User-Serviceable Duty Cycle P P P x x Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about installation, usage, and maintenance.
2. INTRODUCTION Product Overview Voltage Selection Switch (120/230 VAC) DMX In Power In DMX Out Power Out Fuseholder Rear Panel Intimidator™ Scan LED 300 User Manual Rev.
Product Dimensions Page 6 of 17 Intimidator Scan™ LED 300 User Manual Rev.
3. SETUP AC Power The Intimidator™ Scan LED 300 has a dual voltage power supply and it can work with an input voltage of either 120 V, 60 Hz or 230 V, 50 Hz, depending on the position of the voltage selection switch. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator™ Scan LED 300 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and plenty of ventilation.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.
DMX Channels and Functions 11-CH Mode Channel Value Function 000 ó 255 Pan 0–180° 2 000 ó 255 Tilt 0–90° 3 000 ó 006 007 ó 013 014 ó 020 021 ó 027 028 ó 034 035 ó 041 042 ó 048 049 ó 055 056 ó 063 064 ó 070 071 ó 077 078 ó 084 085 ó 091 092 ó 098 099 ó 105 106 ó 112 113 ó 119 120 ó 127 128 ó 191 192 ó 255 Color Open (white) Yellow Pink Green Peachblow Blue Kelly Red Dark blue White/yellow (split colors) Yellow/pink (split colors) Pink/green (split colors) Green/peach blow (split colors) Peachblow/
8-CH Mode Channel Value Function 1 000 ó 255 Pan 0–180° 2 000 ó 255 Tilt 0–90° 3 000 ó 006 007 ó 013 014 ó 020 021 ó 027 028 ó 034 035 ó 041 042 ó 048 049 ó 055 056 ó 063 064 ó 070 071 ó 077 078 ó 084 085 ó 091 092 ó 098 099 ó 105 106 ó 112 113 ó 119 120 ó 127 128 ó 191 192 ó 255 Color Open (white) Yellow Pink Green Peachblow Blue Kelly Red Dark blue White/yellow (split colors) Yellow/pink (split colors) Pink/green (split colors) Green/peach blow (split colors) Peachblow/blue (split colors) Blue/
Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any standalone mode (either Static, Automatic, or Sound) to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Sound-Active Mode To enable the Sound-Active mode: 1.
Master/Slave Mode The Master/Slave mode allows a single Intimidator™ Scan LED 300 unit (the “master”) to control the actions of one or more Intimidator™ Scan LED 300 units (the “slaves”) without the need of a DMX controller. The master unit will be set to operate in either Auto program or Sound-Active mode, while the slave units will be set to operate in Slave mode. Once set and connected, the slave units will operate in unison with the master unit. Configure the units as indicated below. Slave units: 1.
Changing Gobos To change the gobos in the Intimidator™ Scan 300, you do not need to remove the gobo wheel. Simply: 1. Turn off and disconnect fixture from power outlet. 2. Place the product on a flat, level surface with the front facing up. 3. Open the head cover by loosening the ten fastening screws at the sides of the top cover. 4. Remove the four screws on the cover plate underneath the display to access the gobo wheel. 5. Rotate the gobo wheel until the gobo that needs replacing is accessible. 6.
5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, clean the product at least twice a month. Use and environmental conditions could cause increased cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power. • Wait until the product is cold.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 11 in (279 mm) 10 in (254 mm) 18.9 in (478 mm) 14.7 lbs (6.7 kg) Note: Dimensions in inches rounded to the nearest decimal digit.
In case you need to return a product or request support, follow the procedure below: • • • If you live in the U.S., contact CHAUVET® World Headquarters (see below). If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your distributor of record. See www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or Ireland. If you live outside the U.S.