Intimidator™ 2.0 HTI DMX-616 USER MANUAL Intimidator™ 2.0 HTI Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.
TABLE OF CONTENT TABLE OF CONTENT........................................................................................................................................................... 2 BEFORE YOU BEGIN........................................................................................................................................................... 3 WHAT IS INCLUDED .................................................................................................................................
BEFORE YOU BEGIN What is included ¾ ¾ ¾ ¾ 1 x Intimidator™ 2.0 HTI Intelligent Mirror Scanner Power cord with plug HTI-150W lamp Warranty Card Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
INTRODUCTION Features Intimidator™ 2.0 HTI Control Features • • • • • • 5 channel DMX Intelligent Scanner Strobing Gobo Wheel - 14 gobos plus open - 12 metal, 2 glass - Gobo Bounce™ Color Wheel - 11 colors plus open - (include UV purple) plus white Pan: 180° in .5 sec. Tilt: 90° in .3 sec.
Product Overview Mirror Scanner Hanging Yoke, double bracketed for floor positioning Power & Fuse compartment Lamp access cover Dipswitches Microphone Intimidator™ 2.0 HTI DMX connectors Double bracketed yoke used for floor positions. Voltage Switch Sound Sensitivity Knob Remote Controller Input Intimidator™ 2.
SETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. An HTI-150W high intensity discharge lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation.
Setup Lamp Alignment How-To Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is referred to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. There are three lamp alignment screws S2 provided at the base of the projector head. Turning these screws allow you to optimize the projection quality of the spot as well as the overall intensity of the beam. S2 1.
Setup Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation. R IG G IN G Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs.
OPERATING INSTRUCTIONS Operating Modes • • • A stand-alone mode will listen to sound and run through its diverse range of built in programs. Master/Slave mode will allow the command of up to as many units you want in a synchronized light show to the sound. DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be controlled individually using any universal DMX-512 controller.
Operating Instructions If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that will help you understand its use. Set the start address using the group of DIP switches located usually on bottom of the fixture. Each dip switch has an associated value. Adding the value of each switch in the ON position will provide the start address.
CA-9 Easy Controller (Optional) Stand By Blackout Mode LED ON: Slow Mode Function Pan & Tilt is sound activated but Gobo and Color wheel are static and controlled by the Function button. Tap the Function button to step through the 11 colors then once more to step to the next gobo. LED OFF: Fast Mode The unit’s movement Pan & Tilt and Gobo/Color is sound activated. Press and hold the Function button to achieve the following results. a. . Strobe in different colors and gobos Intimidator™ 2.
APPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. Choosing a start address should be planned in advance.
Appendix DMX Channel Values Channel Value 1 000 Ù 015 016 Ù 091 092 Ù 135 136 Ù 195 196 Ù 255 Strobe Gobo Stopped Adjacent gobo strobe: Slow > Fast Adjacent color strobe: Slow > Fast Adjacent color and gobo strobe: Slow > Fast Gobo Bounce™: Slow > Fast 2 000 Ù 007 008 Ù 015 016 Ù 023 024 Ù 031 032 Ù 039 040 Ù 047 048 Ù 055 056 Ù 063 064 Ù 071 072 Ù 079 080 Ù 087 088 Ù 095 096 Ù 103 104 Ù 111 112 Ù 119 120 Ù 127 128 Ù 255 Gobo Blackout Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo
Appendix surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or becomes dirty, clean the lamps with an alcohol wipe. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.
General Troubleshooting Symptom Applies to Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check fan thermal switch reset 9 Beam is very dim or not bright Clean optical system or replace lamp 9 Breaker/Fuse keeps blowing Check total load placed on device Chase is too slow Check users manual for speed adjustment 9 9 9 Device has no power Check for power on Mains. 9 9 9 9 9 9 9 Check 220/110v switch for proper setting 9 Check device’s fuse.
Appendix Technical Specifications WEIGHT & DIMENSIONS Length........................................................................................................................ 584.2 mm (23.0 in) Width ......................................................................................................................... 266.7 mm (10.5 in) Height ........................................................................................................................ 171.5 mm (6.75 in) Weight ..........