User Manual
Edition Notes Edition Notes Trademarks Copyright Notice Manual Usage The Amhaze™ User Manual Rev. 05 covers the description, safety precautions, installation, programming, operation, and maintenance of the Amhaze™. CHAUVET® released this edition of the Amhaze™ User Manual in May 2012. CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or CHAUVET).
Table of Contents Table of Contents 1. Before You Begin ............................................................................................... 1 What Is Included ............................................................................................................ 1 Unpacking Instructions ................................................................................................... 1 Claims .................................................................................................
NOTES -b- Amhaze™ User Manual Rev.
Before You Begin 1. Before You Begin What Is Included Unpacking Instructions Claims • • • • • One Amhaze™ with Flight Case One Power Cord (2 M) One Fluid Tank (5 Liter) One Warranty Card One User Manual Immediately upon receiving this product, carefully unpack and check the container. Make sure you have received all the parts indicated above and all the parts are in good condition.
Before You Begin Safety Notes There is risk of burns or electric shock while operating this product. Read all the following Safety Notes before working with this product. These Notes include important information about the installation, usage, and maintenance of this product. There are no user serviceable parts in this product. Any reference to servicing in this User Manual applies only to properly certified CHAUVET® technicians. Do not open the housing or attempt any repairs unless you are certified.
Introduction 2. Introduction Product Description The Amhaze™ is a professional, water-based, DMX controllable haze machine that provides continuous output with various degrees of density. It consists of a chassis that contains the pump, fan, power supply, DMX connections, and control panel. It comes installed in a stackable flight case that also provides room to keep the fluid tank during operation.
Introduction Product Overview 3- & 5-pin DMX connectors Control Panel (LCD) Control Panel (Buttons) -4- Amhaze™ User Manual Rev.
Setup 3. Setup AC Power This product comes in two models, each with a fixed input voltage power supplies, either 120 V, 60 Hz or 230 V, 50 Hz. Therefore, you have to order the correct model for the line voltage in your area. Make sure that you are connecting this product to the proper voltage, as per the specifications in this guide or on the product’s sticker. Always connect this product to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
Setup DMX Linking You may link the Amhaze™ to a DMX controller using a standard DMX serial connection. If using other DMX compatible units with this product, it is possible to control them individually with a single DMX controller. DMX Mode The Amhaze™ uses the standard DMX data connection for the 2-Channel DMX mode. Refer to the Introduction chapter for a brief description of this mode. Refer to the Operation chapter to learn how to configure the Amhaze™ to work in this mode.
Operation 4. Operation Preparation Once installed, you have to prepare the Amhaze™ for operation. To do so, follow these steps: 1. Open both ends of the flight case. 2. Pull out the fluid tank. 3. Remove the cap of the fluid tank. 4. Verify that the two plastic hoses attached to the cap are in place and in good condition. 5. Pour Chauvet (PHF) haze fluid inside the tank. 6. Replace the cap of the fluid tank making sure that is tightly closed 7. Reinsert the tank. 8.
Operation Startup The Amhaze™ does not have an On/Off switch. As soon as you connect the Amhaze™ to the power outlet, it will start operating. To start up the Amhaze™, do the following: 1. Insert the Neutrik® powerCON® A connector of the power input cord into the lockable (blue) socket on the back of the Amhaze™. 2. Turn the connector right until it locks in position. 3. Plug the power input cords to a suitable power outlet (the display will show “Warm Up Cycle”). 4.
Operation Programming Timer Mode Parameters Continuous Mode Parameters The Programming mode allows you to change the options that affect the various operating modes as well as setting the DMX address. These parameters determine the on and off intervals as well as the output volume when the Amhaze™ is in Timer mode. To configure these parameters do the following: 1. Press repeatedly until “TIME INTERVAL” shows on the display. 2. Use or to set the time off timer (1~200 s). 3.
Operation Menu Map Auto Display CHAUVET AMHAZE (Displayed for 2 seconds) WARM UP CYCLE READY TO HAZE FLUID SENSOR OFF (or) ON Press FLUID Sensor Start Mode ADD FLUID AIR PUMP FLUID Sensor Start Mode ERROR : FLUID IN AIR PUMP ERROR Press FLUID DELIVERY ON Functions Menu (Press to Navigate) TIMER INTERVAL: 1~200 sec TIMER DURATION: 1~200 sec FLUID SENSOR: ON/OFF TIMER VOLUME: 1~100 % VOLUME MODE OUT: 1~100 % Press Use or change settings VOLUME
Technical Information 5. Technical Information Hazer Maintenance Do not allow the hazer to become contaminated. After 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20% distilled vinegar through the system to prevent the accumulation of particulate matter in the heating element. The recommended cleaning routine is as follows: 1. Empty all fog liquid from the machine. 2. Add cleaning solution to tank. 3.
Technical Information Troubleshooting Guide Symptom Unit powers up but it generates no haze Haze comes out but it is too thick/thin Circuit breaker/fuse keeps tripping/blowing Unit does not power up Unit does not respond to wired DMX or responds erratically Cause(s) Hazer is still cold Wrong fluid Lack of fluid Faulty pump Erroneous haze volume adjustment Wrong fluid Faulty pump Excessive circuit load Short circuit along the power wires No power Loose or damaged power cord Built-in breaker tripped Fault
Technical Information Returns Procedure The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the unit. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization (RMA) number.
Technical Information Technical Specifications Dimensions and Weight Length 24 in (610 mm) Width 20.9 in (530mm) Height 7.8 in (199 mm) Weight 46.3 lbs (21 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Electrical Haze Production Thermal DMX Ordering -14- Power Supply Type Conventional (transformer) Range 120 V, 60 Hz or 230 V, 50 Hz Voltage Selection Fixed voltage models Parameter Consumption Operating current Circuit breaker 120 V, 60 Hz 830 W 6.
Technical Information CHAUVET® 5200 NW 108th Avenue Sunrise, FL 33351 (USA) (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com Amhaze™ User Manual Rev.