USER MANUAL Model: QL-M210 support@chargenius.
Silicone Mat Automa�c Clamp Arms Touch Button (two sides) Indicator Lights (two sides) Adjustable Feet What is included Qi wireless Charger X 1 CD Slot Mount x 1 + Spacer x 3 (1.5 ~2.5mm) Suc�on Cup Mount X 1 Air Vent Clip X 1 QC 3.
Features: 1. All-in-one moun�ng pack, mul�ple moun�ng op�on for moun�ng the wireless charger in your car. 2. Smart touch bu�on and LED indicator on both sides, fully automa�c induc�on wireless charging, one hand opera�on. 3. Built-in wireless charging transmi�er, support Qi wireless charging for all Qi-enabled smartphones. 4. Adjustable bo�om tray, suitable for different size of smartphones, an�-slip silicone on both arms, USB Type-C charging port. 5. Built-in stepper motor, works without noise. 6.
Product Overview Product Installation Install Dash Mount Holder: 1.Insert the adjuster knob into the ball joint onto the Car Mount Holder. 2.Push the ball joint into the socket at the back of the wireless charger unit and fasten the adjuster knot. Adjust the wireless holder to the op�mal viewing angle and �ghten the nut. 3.***Important*** Please clean the dashboard or windshield first before moun�ng the car mount holder. This is to prevent the dust or small par�cle to be mounted inside the suc�on cup.
Install Air Vent Clip: 1.Insert the adjuster knob into the ball joint onto the Air Vent Clip. 2.Push the ball joint into the socket at the back of the wireless charger unit and fasten the adjuster knob. 3.Insert the Vent Clip into the car’s air vent, adjust the wireless charger unit to the op�mal viewing angle. ***Important*** DO NOT insert the adjustable stand into the car vent.
Install CD Slot Mount: 1. Insert the adjuster knob into the ball joint onto the CD Slot Mount. 2. Push the ball joint into the socket at the back of the wireless charger unit and fasten the adjuster knob. Place “rubber spacer” on the center of mount insert. Try with 1.5 mm rubber spacer first and see if the mount is secured, if not, change to 2.0 or 2.5mm. ***Important*** Adjust ball joint pole between 45 ~80 degree for be�er vewing angle and stable hold. 3.
Mount your smart phone 1. Connect the USB cable to the QC 3.0 Port (Orange Color) on the Car Charger Adapter 2. Plug in the Car Charger Adapter into cigare�e lighter or power outlet in your car 3. Connect the Type-c cable head into the charging port on the rear of the charger unit 4. Adjust the bo�om tray so your smart phone will align to the center of the charger unit LED Indicator Solid Blue: Standby Mode Solid Green: Charging Mode 1. Please use the product correctly according instruc�ons 2.
Supports Charging with Phone Case 6m m Charge your phone without taking off the case. Thickness of the case should be less than 6mm / 0.24 inch.
A�en�on 1. Please use the product correctly according instruc�ons 2. Please do not disassemble the product or throw it to fire and water, to avoid leakage caused by electrical short circuit 3. Please do not use wireless charger in high temperature, wet, corrosive environment, to avoid leakage from caused by damaged circuit 4. Please do not put wireless charger close to cards with magne�c stripes or chips (ID card, credit card etc.) to avoid demagne�za�on 5.
FCC Statement: Changes or modifica�ons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec�on against harmful interference in a residen�al installa�on.
THANK YOU SO MUCH For Purchasing CharGenius Product. Our goal is to make sure that our customers are completely sa�sfied with the purchase. We Want You to Be Happy! Was there any damage to the product or was something not quite right a�er you received the package? No problem! Please reach out to us right away. Confused or Problems about using the Product? 1. Open the camera on your smart phone, point and scan the code. Wait for your device to recognize the QR code. Tap the no�fica�on to open the link. 2.