Use and Care Manual

6-4626
Shut-o Handle
Mango de cierre
Poignée du robinet
WARNING
Parts, Piezas, Pièces
6-6136
Hose
Manguera
Tuyau
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
4. Pre-Use Check
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6. Pressurizing and Spraying
8. Care, Storage and Maintenance
2-1091-100 (A) R0116
Adjust spray pattern by
turning nozzle cap. Do
not turn cap more than 2
turns or cap may come o
allowing spray material to
spray back on you.
7. To Release Pressure
Do: With valve facing away from you, lift and hold the cap until air is com-
pletely exhausted, OR, turn the valve slowly counterclockwise until you hear
air escaping and wait air is completely exhausted.
1. Hose to Tank
Make sure white outlet tube
is attached to hose.
Insert tube into tank.
Proper placement of
white outlet tube.
Line up tabs on safety
lock connector with
notches on the outlet
ange of the tank. Insert
tabs into notches to form
a secure seal.
Slip hose nut down to
tank, turn clockwise
and tighten as tight as
possible by hand.
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Do: Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn coun-
terclockwise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn
1/4 turn clockwise to lock.
Begin spraying. Re-pump
sprayer as required to main-
tain spray force.
1A
1B
1C
1D 1E
7A
9. Fatigue-Free Spraying
3. Filter
e lter helps prevent clogging while spraying. It is located on the end of
the outlet tube inside your sprayer tank.To clean lter, remove the discharge
assembly from the tank (Fig.1A, 3A). Make sure the lter is positioned at the
bottom of the tank as pictured.
Note: Filters are not supplied with deck sprayers.
Filter
3A
6B6A 6C
6D
6-7748
Extension wand, Vara de extensión, Rallonge
#2802E, 2803E
2. Nozzle
6-8131
Nozzle
Tobera
Buse
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer
Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador
en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin. Enregistrez dès
que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
6-7756
Extension wand, Vara de extensión, Rallonge
#2601E, 2602E, #2603E
6-4645
Relief Valve
Válvula de descarga de presión
Soupape de décompression
#2601E, 2602E, #2603E
6-3337
Straps
Tirantes
Sangles
Attach nozzle to shut-o
handle or extension wand.
For constant spraying, push down on shut-o handle and move grey lock-
ing mechanism away from you. To release, squeeze handle and move the
grey locking mechanism back towards you. ( Not all models are provided
with this feature).
9A
Locking
mechanism
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original
parts. Never spray ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of
deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these
conditions are found, replace aected part with original manufacturer’s part before using.
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with water
after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
10. Troubleshooting - Tank pressurizes but does not spray.
WARNING: Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 10E) -Remove nozzle cap by unscrewing. Clean and re-assemble.
Clean shut-off (Fig. 10A- 10D)
10E
Nozzle Cap
Pull handle straight
up.
Insert notches from
underside of handle
into plunger grooves
and turn counter
-
clockwise.
Tighten plunger clockwise until
ush to top of shut-o body. Do
not over-tighten or unit may not
spray. Slide forks under plunger,
push handle down until it snaps
into place.
10A
10B
Handle
10D
Plunger ush
with body
Or
Remove plunger, diaphragm and
spring. Wash diaphragm with
mild detergent. Reassemble: Hold
shut-o upright as shown, place
spring in hole, place diaphragm
on top of spring. Reassemble
plunger and tighten.
10C
Plunger
Spring
Diaphragm
WARNING: is product contains chemicals, including lead, known to the state of California
to cause birth defects and other reproductive harm. Wash hands after handling.