6-Channel Digital Proportional R/C System User Manual ATTENTION ● Please read this manual carefully before use. ● Please keep this manual in a safe place after reading. Warranty Card ● A warranty card is included in the kit. Please stamp the model store signature and purchase date at the time of purchase.
TABLE OF CONTENTS INTRODUCTION............................................... 4 •Support and Service .......................................... 4 •S.BUS Wiring example .................................... 38 •Application, Export, and Modification............ 5 •S.BUS/S.BUS2 device setting .......................... 40 • Compliance Information Statement ............... 5 •Switch harness .................................................. 41 •S.BUS2 System .............................................
TABLE OF CONTENTS Throttle cut ..................................................... 83 Idle down ......................................................... 84 Swash ring (Heli only).................................... 85 Swash (Heli only, except H-1)........................ 86 Stick alarm ...................................................... 88 Timer ............................................................... 89 Function name ................................................ 91 Telemetry system ........
Introduction Thank you for purchasing the Jumper® JumperTX-2.4GHz System T16 Remote Control. The system is versatile and can be used by beginners and professionals. Please read this instruction manual carefully before use to ensure correct and safe use. Due to version upgrades, there have been changes. The information contained in this manual is subject to change without notice. This T16 transmitter is suitable for all types of models of fixed wings, gliders, helicopters and multi-rotors.
Precautions for ensuring safe use: Please observe the following precautions to ensure that the product is always used safely. The meaning of special tags: From a safety point of view, the parts marked with the following marks in this manual require special attention. = Prohibited = Pay Attention Warning: Keep away from children at all times. Flight considerations: caveat Never hold the antenna of the transmitter during flight.
Do not operate remove control craft in the following situations. ■ If others a operating RC craft near by ■ In cities or populated areas. ■Near airports or hospitals or any take of and landing point or real aircraft. ■In places prohibited by law to operate RC craft. Ensure to check all flight control surfaces working Correctly before flight.
■ Charging exceeding the specified value may cause the battery to heat up, rupture, leak, or catch fire. Waiting for danger. Do not charge more than 1C when charging quickly. ■ Do not charge in the car while the vehicle is in motion. Vibration, etc. will cause possible problems. Make sure the power plug is fully inserted into the socket hole Be sure to use the charger according to the specified power supply voltage. WARNING Batteries can get hot during charge, Be careful when charging batteries.
Precautions when using an SD card WARNING Do not modify or damage the SD card Do not use excessive force or bend SD Card Do not allow the SD card to become wet or exposed to Sunlight. WARNING ■ SD cards are electronic products, so be careful to prevent static electricity. It may cause malfunction due to malfunction. Keep the remote-control SD card slot clean to prevent foreign matter from entering。 ■A Do not use it on radios, TVs, stereos, etc. Use near devices where interference occurs.
Before use Features: 2.4G multi-function 16 channel transmitter (T16) The T16 uses a 2.4 GHz two-way communication system. The data transmitted from the receiver can be received and confirmed by the remote controller. Color LCD screen With a 4.3-inch large color LCD screen, the operation at the time of setting is greatly improved. S.BUS system The receiver supports the S.BUS interface and can be used with the T16 up to 16 channels.
Package content Your T16 includes the following components: (Depending on the package, the accompanying content will vary.) • T16 remote control • Receiver • 18650 lithium battery tray • Orange lanyard • User's manual • Only Chinese formal sales channels are equipped with this Chinese manual. T16 Remote Control Remote control frequency: 2.4GHz System: JumperTX mixed control + multi-protocol high frequency transmission Power supply: 7.
Components The LCD screen used in this manual may be upgraded according to the settings and version.
Direction of the antenna The remote-control antenna has directivity. The signal strength is greatest in the horizontal direction. Therefore, please try not to let the antenna point in the direction of the body. The antenna can be rotated to adjust the angle. Please adjust the position of the antenna according to the operating habits. Antenna adjustment range The horizontal rotation angle of the antenna is 360 degrees, vertical rotation. The angle range is 90 degrees.
2 Position 3 Position 1 Position Momentary
Knob operation Digital fine-tuning operation This transmitter is equipped with 6 trimmer switches. Each time you touch the fine adjustment switch, the corresponding fine adjustment position will move according to the fixed span. However, if you keep pressing the fine adjustment switch, the movement speed of the fine adjustment position will increase, and a “beep” sound will be emitted to the boundary point. Knob operation The volume S1and S2 knobs allow analog input.
Slide Lever S1 (Left), S2 (Right): The Linear Slider S1and S2 offer analog input. *The T18SZ transmitter beeps when the lever comes to the center. *You can select a slide lever and set the movement direction on the setting screen of mixing functions.
Example of operation of digital fine-tuning *Example using Mode2 ◆ Elevator and joystick in neutral position, aircraft out the situation of rising action. ◆ Elevator and joystick in neutral position, aircraft There is a decline. Elevator fine-tuning down Elevator neutral position Elevator neutral position Move slightly to the lower side Move slightly to the upper side ◆ After several adjustments, the model will resume horizontal flight.
Battery installation and use Installing/removing the FT2F2100B V2 BEFORE USE 19
Joystick operation *Example using Mode2 Elevator operation Aileron operation Pitch axis Heading axis Engine Motor Output Throttle Operation 24 BEFORE USE Rudder operation
Example of joystick operation: fixed wing example * Example using Mode2 The method of operation may vary depending on the model.
Example of joystick operation: helicopter example *Example using Mode2 The method of operation may vary depending on the model.
Example of joystick operation: multi-rotor example *Example of Mode2 The method of operation may vary depending on the model.
Joystick adjustment method Length adjustment of the joystick head Angle adjustment of the joystick Use a 1.5mm hex wrench Joystick head Joystick lower The length of the joystick head can be adjusted 1. Fix the joystick head B and rotate the joystick The neutral angle of the joystick can be adjusted Slightly to the inside or outside. 3. head A counterclockwise to unlock 2. Move and hold the joystick head B in the direction you want to adjust, then rotate the joystick head A clockwise until it locks.
Adjustment of Throttle Stick (Ratchet System) You can choose either airplane ratchet system or helicopter-touch. 1. Open the dust protection cap on the back of the transmitter that is covering the hole for throttle stick adjustment. 2. Use the attached 1.5mm hexagonal wrench (inside stylus) to turn the adjustment screw and set it as you prefer. Turning the screw clockwise increases the tension. For airplanes: Adjust the screw on the left. For helicopters: Adjust the screw on the right.
TF Card (secure digital memory card) (not included) The T18SZ transmitter model data can be stored by using any commonly found SD card. When T18SZ transmitter update software is released, the software is updated using an SD card. The T18SZ is capable of using SD and SDHC cards (SD:32MB-2GB SDHC:4GB-32GB). TF card reader/writer Saving model data and update files (released from Futaba) into the SD card, you can use those files on your T18SZ transmitter.
CAUTION Be sure to turn off the power to the transmitter before inserting or removing the SD card. As the SD card is a precision device, do not use excessive force when inserting. -When an SD card is installed in the T18SZ transmitter, a folder called "Futaba" is created. Folders called "LOG" and "MODEL" are created in this folder. The "MODEL" folder stores the model data and the "LOG" folder stores the telemetry log data.
Before Use This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
