How-To Guide

ManualsBrandsChangzhou Smoothies Electronics ManualsElectronicsMULTIPROTOCOL TX

JUMPER JP4IN1 Multiprotocol Module

Brief Introduction:

The JP4IN1 integrates the CC2500,chips into one PCB. The JP4IN1 is an OpenTX original

accessory which can do serial digital signal communication with the Frsky series radios.

Recognizing PPM signal from radio output, then converted to the corresponding radio protocol

to achieve control of the fixed wing and drone aircraft. Supported protocols such as: Walkera

DEVO, Spectrum DSM2/DSMX, Flysky, Esky, Frsky, WLtoys, Hubsan, Hisky, Futaba SFHSS Assan

etc are built in..

The JP4IN1 module offers greater flexibility with the ability to control most protocals and

popular brands in the market today. It also gives the user the ability to use a real RC radio for

more precise control and a better flying experience than the small radios often included with

ready to fly products.

Note: due to the copyright of the protocol, JP4IN1 only provides hardware, please refer

following link to download the firmware:

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module

How to install firmware with USB port? Need some clear and simple instructions.

Instructions at the link above are very complicated and needs USBAVR etc.

Summary of content (7 pages)

PAGE 1
JUMPER JP4IN1 Multiprotocol Module Brief Introduction: The JP4IN1 integrates the CC2500,chips into one PCB. The JP4IN1 is an OpenTX original accessory which can do serial digital signal communication with the Frsky series radios. Recognizing PPM signal from radio output, then converted to the corresponding radio protocol to achieve control of the fixed wing and drone aircraft.
PAGE 2
Parameters: Weight: 42g (include antenna) Dimension: 61.1*48.9*32.8mm (exclude antenna) Shell shape compatible with: Frsky, JR radio etc. MCU: STM32F103CBT6 (128K ROM, 20K RAM) Working voltage:6-9 V Working current: <=100mA Working frequency: 2.4G ISM band Two working modes: Serial Port mode & PPM mode. 1. Normal operation in Serial Port mode (Bi-directional digital signal communication between radio and JP4IN1.
PAGE 3
Once X9D finished upgrade: power off radio, insert JP4IN1 module, then power on again. (Note: please make sure JP4IN1 antenna is assembled before powering on radio). As shown in below Fig: Enter the “MOEL SET UP” menu, close Internal RF and open External RF, the red and green led both are on. Select the protocols and sub protocols you need for bind in External RF menu, and then "bind".
PAGE 4
Support Protocol List Protocol Sub protocol or Option FLYSKY Nil HUBSAN FRSKYD Nil Nil Hisky HK310 Nil HISKY V2X2 DSM2_22 DSM2_11 DSM DSMX_22 DSMX_11 DEVO YD717 KN SYMAX SLT CX10 None YD717 SKYWLKR SYMAX4 XINXUN NIHUI WLTOYS FEILUN SYMAX SYMAX5C Nil CX10_GREEN CX10_BLUE DM007 Q282 JC3015_1 JC3015_2 MK33041 Q242 Supplementary Specification Flysky first generation protocol Hubsan Frsky D series protocol Hisky Hisky DSM2 protocol, frame rate 22mS DSM2 protocol, frame rate 11mS DSMX protocol, frame
PAGE 5
SHENQI FY326 CG023 YD829 H8_3D Nil CH_16 CH_8 Nil MT99 H7 YZ LS WLH08 X600 X800 H26D E010 Nil Nil S-FHSS Nil J6PRO FQ777 ASSAN FRSKYV HONTAI Nil Nil Nil Nil FORMAT_HONTAI FORMAT_JJRCX1 FORMAT_X5C1 CG023 BAYANG FRSKYX ESKY MT99XX MJXQ Jumper X68T Frsky protocol, D16 mode Frsky protocol, D8 mode Esky protocol MJX series protocol E010 and JJR H36 protocol Futaba S-FHSS protocol(updating) Nine Eagle J6PRO protocol Frsky V series protocol More details, please refer to:: https://github.
PAGE 6
Turn on or turn off the green light procedures are as following： Turn off radio, rotate the encoder knob switch to "0" position, then press and hold the black bind button, power on the radio meanwhile, release the button after 3 seconds, the green light will flash, optional protocols switch simultaneously. Normal use and operation in PPM mode: 1. Fix JP4IN1 with antenna on the radio, open PPM signal output of radio. 2. Turn the encoder knob (The current position i.e.
PAGE 7
Firmware update, please refer to: https://github.com/pascallanger/DIY-Multiprotocol-TX-Module FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.