The Federal Communication Commission Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication.
The antenna(s) used for this transmitter must not be co-located of operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Ln order to avoid the possibility of exceeding the Fcc radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during normal operation.
Copyright © 2016, Scantech-ID BV. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Scantech-ID BV. Limited Warranty Under all circumstances this manual should be read attentively, before installing and/or using the product.
1 Table of contents Table of contents..........................................................................................1 Preface .................................................................................................3 Chapter 1 Product Safety............................................................................4 1.1 Used conventions .............................................................5 1.2 Laser safety ..................................................................
Preface 2 Chapter 5 Configuring the ShuttleC............................................................. 27 5.1 Making Connection and Login.......................................... 28 5.2 Wired network settings ................................................... 31 5.3 WiFi networksettings……………………………….............. 32 5.4 SG-15 Price Checker Settings ......................................... 37 5.5 Configuring the Bar Code Reader….................................. 43 5.
Preface C The Shuttle is an entry level, small and attractive Price Checker. The ShuttleC features the latest technology. Interfacing is done either through Wireless RF or hard wired Ethernet. The bright colour display has, depending on the used font set, 3 or 5 lines and can display up to 20 characters per line. There is a choice of bar code scanners between the high performance 24 scan lines laser scanner, 2D imager and the low cost single scan line CCD scanner.
Chapter 1 Product Safety
C Colour Scantech-ID Shuttle SG-15 1.1 USED CONVENTIONS In this manual the following conventions are used: ATTENTION Gives a tip, an instruction or a point of attention. IMPORTANT Warns for possible damage to the scanner or other objects when not following an instruction. DANGER! Warns for possible harm to persons when not following an instruction. 1.2 LASER SAFETY ATTENTION During installing, always follow the instructions. DANGER! Do not stare into the laser beam.
6 Product Safety German: C Der Strichcode-Scanner SHUTTLE entspricht den Sicherheitsvorschriften nach IEC 825-1 (1993) für ein Laserprodukt der Klasse I. Er entspricht auch U.S. 21CFR1040, anwendbar auf ein Laserprodukt der Klasse IIa. Vermeiden Sie langzeitiges Hineinblicken in direktes Laserlicht. Dutch: De SHUTTLEC scanner voldoet aan de veiligheidsnormen IEC 825-1 (1993) voor een Klasse I laserproduct. Tevens voldoet de scanner aan U.S. 21CFR1040, van toepassing op een Klasse IIa laserproduct.
C Colour Scantech-ID Shuttle SG-15 7 Spanish: El scanner SHUTTLEC reune las normas de seguridad IEC 825-1 (1993) para un producto laser de Clase 1. Y también reune las normas U.S. 21CFR1040 que se aplican a un producto laser de Clase IIa. Se debe evitar mirar muy fijo en luz lasérica directa. English: The SHUTTLEC scanner complies with safety standard IEC 825-1 (1993) for a Class I laser product. It also complies with U.S. 21CFR1040 as applicable to a Class IIa laser product.
8 1.
C Colour Scantech-ID Shuttle SG-15 9 Declaration of Compliance ROHS II Company Name: Champtek Incorporated Product Model Name: SG-15Colour We certify the above listed product, parts, materials and packaging are in compliance with the European Economic Union (EEU) “Reduction of Hazardous Substances” (RoHS II) Directive 2011/65/EU, except for the exemptions listed under RoHS II.
10 1.
Chapter 2 General Description
12 2.1 General Description C USE OF THE SHUTTLE C The Shuttle is a Price Checker, which provides the user with the opportunity to scan their chosen product and display product information or verify the price C before getting to the checkout. Apart from this, the Shuttle offers the ability to interface with loyalty cards, display special offers, display dual currency, etc. Moreover, store level profitability can be increased.
C Colour Scantech-ID Shuttle SG-15 2.2 13 C CONSTRUCTION OF THE SHUTTLE SG-15 COLOUR C The various parts of the Shuttle are indicated in figure 2.1: A. Front housing with window B. Colour TFT-LCD Display size is 320X240 pixels QVGA 70 X 53 mm Color Depth 16.7M Colours C. Back Housing D. Scantech-ID omni-directional scanner, 2D Imager or CCD single line scanner E. Main board F. Back Cover. F B E C D A Fig 2.
14 General Description 2.3 C FUNCTIONING OF THE SHUTTLE SG-15 COLOUR 2.3.1 Introduction C The Shuttle is an information terminal, which receives input (barcode), from a user and answers via the display. The display contents is provided by a computer application, which runs on a (server) system elsewhere. 2.3.
C Colour Scantech-ID Shuttle SG-15 15 2.3.4 Software & Control C The functions during daily use of the Shuttle are determined by the application C program, which is controlling the Shuttle . So the task of the storage of databases, providing the information and sending it to the display of the ShuttleC will be performed by a central host system. Providing this application, running on the host system, is the responsibility of the System Integrator.
16 2.4 General Description POWER OVER ETHERNET (POE) C The alternative for powering the Shuttle through an external PSU (adapter), is using the Power-Over-Ethernet (PoE) version of the SG-15Colour. In this way the SG-15Colour is powered directly through the Ethernet and you don’t need to install a (230/110VAC) mains socket anymore somewhere in the middle of the store, so in this way saving you quite some installation costs! The ShuttleC PoE complies with the official standard: IEEE 802.3af.
C Colour Scantech-ID Shuttle SG-15 Chapter 3 Installation of the ShuttleC SG-15Colour 17
18 3.1 Installation UNPACKING C Unpack the Shuttle as follows: 1. Take the ShuttleC and its accessories out of the box. 2. Remove the packing material. 3. Check the packing list to make sure you have received all of the items ordered. 4. Visually inspect the ShuttleC and accessories for any evidence of physical damage. 5. If anything is missing or appears to be damaged, immediately contact your dealer.
C Colour Scantech-ID Shuttle SG-15 19 A A fig 3.1 ATTENTION Mount the ShuttleC on a height for convenient • view of the display • scanning of the articles. 1. See Drilling Template in Appendix P and mark the locations for the mounting holes on the wall and drill the two holes. 2. Put plugs in the holes. 3. Connect the power cable and the communication cable of the ShuttleC (see figure 3.1 above). 4. Fasten the ShuttleC to the wall by clicking it on the 2 screws (parkers, indicated by A).
20 Chapter 4 System Integration Installation
C Colour Scantech-ID Shuttle SG-15 4.1 21 SOFTWARE C The Shuttle is a thin-client, front-end Price Checker. Its behavior is very easily C configurable and fully determined by the software package, driving the Shuttle from the Back-Office/server. This software package (or: added value) will be supplied by the System Integrator. This is because of the fact that there are no set international standards with regard to product database structures and/or programming languages.
22 System Integration 4.1.2 Scantech Tools and Drivers In order to support our System Integrators in the best possible way, Scantech ID supplies: 1. Extensive documentation describing all details of the product. (this manual and more). 2. Built-in Configuration Utility through web browser: See chapter 5. ATTENTION Colour The SG-15 runs an embedded web server for configuration Colour purposes. This makes it possible to configure an SG-15 with any modern internet browser. 3.
C Colour Scantech-ID Shuttle SG-15 23 4.1.3 Compatibility Colour is an entry level Price Checker with basic function, so it does not 1. The SG-15 require an advanced and extensive set of commands to control it, compared it to previous model(s). Colour As of the new SG-15 , the Shuttle can now be configured in such a way, it is backward compatible with the Discovery SG-20*1. See Chapter 5.4 for configuration details.
24 4.2 System Integration HOW TO COMMUNICATE? A SIMPLE EXAMPLE Colour The SG-15 is a simple IP device in the local network, which accepts and displays normal ASCII characters. After scanning a bar code, it outputs it as a normal ASCII string.
C Colour Scantech-ID Shuttle SG-15 6. 25 See Appendix B for more recommendations how to control the SG-15Colour display and Terminal itself. Some notes: 1. Regarding the Network Connection Properties of your PC: Make sure the IP address of your PC is in the same IP range as the ShuttleC you want to communicate with. For instance by giving your PC IP address: 192.168.1.200 2. If you have a firewall running on your PC, make sure it's not blocking the communication in any way.
26 System Integration
C Colour Scantech-ID Shuttle SG-15 Chapter 5 Configuring the ShuttleC 27
C 28 Configuring the Shuttle 5.1 Making First Connection and Login Colour Note: The information given below is based on SG-15 firmware V0.9.1. The SG-15Colour has an internal web server for configuration purposes. Just start your web browser Chrome, Firefox or Internet Explorer and enter the IP-address of the SG-15Colour. Note: Use for Internet Explorer version 11 or higher.
C Colour Scantech-ID Shuttle SG-15 29 Login Page To manage SG-15Colour settings, it runs a web server in https mode for exchanging queries and responses with a modern browser (Chrome, Firefox or IE). Colour IP address in the address bar of your browser to open the Enter the SG-15 login page.
30 C Configuring the Shuttle On the Home Page you see an overview of the package Versions.
C Colour Scantech-ID Shuttle SG-15 5.2 Configure the SG-15 31 Colour Wired network settings On the Configuration Web Page Wired Network configuration you set the IP address of the SG-15Colour terminal: With Factory default settings, the SG-15 starts with DHCP=On and settings as displayed above. At startup, the assignment of an SG-15 IP-address takes place according the following procedure: 1.
C 32 Configuring the Shuttle Wired Network settings • Static IP Address: fixed IP-address (only editable when DHCP=Off). • Netmask: determines the class of network. • Default Gateway: default IP-address used by the SG-15 whenever it addresses IP's that do not match any other routes in the SG-15's routing table. Notes: 1. The Default Gateway address always shares the network value for the Static IP Address. 2.
C Colour Scantech-ID Shuttle SG-15 33 Notes: 1. At start-up and Wifi-Enable=On, the assignment of the WLAN IP-address is done as follows: 1. When DHCP is enabled and a DHCP-service is available on the network, the SG-15 will use the IP-address assigned by the DHCP-service (the Access Point becomes transparent for any LAN network with an active DHCP-service that answers first in time). 2. When DHCP is enabled but no DHCP-service is available on the network, the SG-15 will use 192.168.4.
34 C Configuring the Shuttle 9. SG-15Colour with WLAN support IEEE 802.11 a/b/g/n/ac, dual-band 2.4GHz/5GHz. Legend Status After entering your Wifi settings and « Apply », the Status line in top of the page will show the new SG-15-WLAN network interface settings.
C Colour Scantech-ID Shuttle SG-15 35
36 C Configuring the Shuttle
C Colour Scantech-ID Shuttle SG-15 37 5.4 SG-15 Price Checker Settings Navigate via Applications to the SGPriceChecker Configuration Web Page, where you configure the Price Checker settings: 5.4.1 SGNET Fill in the fields Server Address and Server Port for connection to the host/server Colour , for instance SGNET service. with the application controlling the SG-15 The Connect Mode can be TCP/IP or UDP (no-connection/state-less). 5.4.
C 38 Configuring the Shuttle 5.4.5 Code-pages The SG-15 supports 12 character sets which you can select from the Codepage drop-down menu. Each character set (code-page) is available in 2 font sizes. Notes: • Font size selection is encoded in the server reply message as an COMMAND, see table below. • Code-page selection is done by web page configuration (i.e. static).
C Colour Scantech-ID Shuttle SG-15 39 5.4.7 Messages This section allows you to define 3 types of messages: Idle, Error and Offline. Each message has a number of reserved lines for entering text. The attributes font, align and XY offsets gives a certain freedom to visualize the messages. Table with legend for message details: Message SG-15 Mode Legend Line[1-3] Idle These messages are displayed when for Idle Display Mode button Text is selected (each message remains TAlt sec on screen).
40 C Configuring the Shuttle 5.4.8 SG-15 Display Features Features When using SGPriceChecker application, • 64 x 128 pixels providing SG-15 backward compatibility mode.
C Colour Scantech-ID Shuttle SG-15 41 5.4.9 SG-15 compatibility table The following table represents the list of commands: Command Character Legend C_CLEARDISPL 0x25 Clear screen (clear screen and cursor moves to home position i.e. Top-Left) C_CURSORPOS 0x27 Position cursor (X[0-15], Y[0-4]) C_ALIGN 0x2E Align a string of text: Left-Top, Center-Top, Right-Top etc.
42 C Configuring the Shuttle
C Colour Scantech-ID Shuttle SG-15 43 Chapter 5.5 Configuring the Barcode Reader Introduction Colour is equipped with a barcode reader of type Omni-Laser, CCD Single The SG-15 Line or 2D Imager. At startup, the SG-15Colour detects what type of barcode reader is installed and it will auto-configure the device according the settings on the Barcode Reader page. Double Read Time This time value (in milli seconds) represents the minimum time between reading one and the same barcode twice.
44 C Configuring the Shuttle
C Colour Scantech-ID Shuttle SG-15 45 5.6 Desktop Configurator Through the Desktop Configurator the application must be selected, which to Start At Boot: SGPriceChecker: or WebPriceChecker: • See web page Applications/DeskTopConfigurator (illustration left) • Click on the SG icon • Edit item • app/sgpricechecker (for instance) is selected and • Set to Start at Boot • Accept Illustration: + Note: Desktop settings are saved in the Templates section.
46 C Configuring the Shuttle
C Colour Scantech-ID Shuttle SG-15 47 Chapter 5.7 Web Price Checker Introduction The web based price-checker application uses a web-kit library to setup a browser-like connection to an http server. When an EAN barcode is scanned, the Colour will send the scanned data as an HTTP request to a web server. The SG-15 web serveris responsible for generating the HTML page with Article/Price/Picture content, which is sent to the SG-15Colour.
C 48 5. Configuring the Shuttle Query URL For every barcode scan, the SK must send a query URL with the requested barcode information to the web-server. The Web-Price-Checker uses tag-variables in the URL for this, like for example: http://192.137.81.60/auth/tbl_products/scan/{@BARCODE}/{@SKTYPE} When scanning an EAN13 barcode 5029053021454 on a SK-50, the URL request with variables, {@SKTYPE} and {@BARCODE} will be reformatted and send to the web server as: http://192.137.81.
C Colour Scantech-ID Shuttle SG-15 7. 49 URL tag-variables recognized by the URL parser Tags according {@...} Description: BARCODE SKTYPE Barcode as read by scan-engine (without identifiers) Mandatory Colour Type of ScanKiosk: SK40, SK50 or SG-15 Optional WIDTH Pixel width of the skweb-screen Optional HEIGHT Pixel height of the skweb-screen Optional Label Identifier for barcode symbologies Optional*1 ID *1 Required: For now, any scanned item is sent without identifier. Notes 1.
50 C Configuring the Shuttle
C Colour Scantech-ID Shuttle SG-15 Chapter 6 Maintaining the ShuttleC 51
52 Appendices 6.1 CLEANING C The Shuttle requires little maintenance. Only occasional cleaning of the scanner and display window is necessary to remove dirt and fingerprints. Cleaning can be performed during operation with a non-abrasive glass spray cleaner and a soft lintfree cloth. Clean the cover and window of the ShuttleC every now and then. Take care of the following: • Use a mild glass spray cleaner; • Spray the cleaner on a soft, lint-free cloth; • Wipe the ShuttleC clean.
54 Appendices
C Colour Scantech-ID Shuttle SG-15 Appendices A Connector types and pin definitions…………………... 56 B Controlling the display and ShuttleC terminal…………. 57 C Character sets…………………………………………. 63 D Factory Default Settings………………………………..65 E Updating Applications or System Packages…………. 66 G Frequently Asked Questions…………………………… 67 H ShuttleC Project tasks…………………………………. 71 I Technical specifications……………………………….. 72 J Overview Partnumbers………………………………….
56 Appendices APPENDIX A PIN DEFINITIONS AND CONNECTOR TYPES Physical Connections Ethernet Connector C 1 2 3 6 - TxC TxRxC Rx- Cable between Shuttle and network connection: Use a standard, ‘8 pin’, 1-to-1 Ethernet network cable to connect the ShuttleC to your Ethernet network. IMPORTANT Make sure you apply proper cabling when using the SG-15Colour Power-over- Ethernet version (IEEE802.3af PoE).
C Colour Scantech-ID Shuttle SG-15 57 C Appendix B Controlling the display and Shuttle terminal Introduction Colour acts a normal remote terminal; Every received ASCII value (between The SG-15 20 and 255), which isn't part of a command, is normally displayed on the screen.
58 Appendices At the end of this Appendix you find the complete command set, including the sub-parameters. On the next pages, you find some examples to give an impression of the way you can use the display of the SG-15Colour. These examples are also shown when using the -simple- demo program SG15Demo.exe. See Appendix K. Note: should be sent as the hexadecimal value 1B. Note: The notation of e.g. 0x24 means the hexadecimal value 24.
C Colour Scantech-ID Shuttle SG-15 59 Example 2 How to create this screen: COMMAND or data string COMMENT 0x42 0x30 Font size 0 0x25 Clear the screen, cursor top left 0x2e 0x31 "Coca Cola 0.33Ltr" 0x03 Align text to center - top 0x2c 0x30 0x45 Set cursor to pixel position (0,21) 0x2e 0x3a "€2.
60 Appendices Example 3 How to create this screen: COMMAND or data string COMMENT 0x42 0x30 Font size 0 0x25 Clear the screen, cursor top left 0x2e 0x30 "Winner" 0x03 Align text to left - top 0x2e 0x32 "Winner" 0x03 Align text to right - top 0x2e 0x36 "Winner" 0x03 Align text to left - bottom 0x2e 0x38 "Winner" 0x03 Align text to right - bottom 0x42 0x31 Font size 1 0x2e 0x34 "You Win!" 0x03 Align text to center
C Colour Scantech-ID Shuttle SG-15 61 SG-15 Command Set V2.0 This command set refers to SG15 plus firmware version 3.03 and higher. COM MAND ESC (1B)16 SUBCOMMAND DESCRIPTION PARAMETERS HEX DEC ESC ESC 24 25 36 37 $ % reserved ESC 27 39 ' Set Cursor Position Set the cursor position on the display. Note : The actual pixelposition 0x30-0x3F depends on the currently selected font set: Every x-position is a multiple of 8 pixels.
62 ESC Appendices 40 64 @ Sleep Clear display and Turn off Laser, Motor and Backlight. plus ESC 41 65 A ESC 42 66 B SG15 keeps functioning as normal. Wake Up Return from sleep Select Font Set plus The SG15 has 2 internal font sets: 0x30 - Font set 1 (Normal sized font) 0x31 - Font set 2 (Large font) ESC 58 88 X Show GIF Displays a GIF on the screen. GIFs and Text can be combined on one screen. The GIF can either be animated or static.
C Colour Scantech-ID Shuttle SG-15 63 APPENDIX C CHARACTER SETS The SG-15 - Colour 0437 0852 0857 0866 0874 1251 1252 1256 1257 GB2312 BIG5 UTF-8 contains 12 character sets: Classic IBM US DOS Latin-2 Central Europe Turkey Cyrillic II DOS Thailand Cyrillic Latin-1 Win Western Arabic Baltic Simplified Chinese Traditional Chinese Unicode (Factory default setting) Only 1 codepage can be used at a time (see chapter 5.8). Each character set (codepage) is available in 2 sizes (see "ESC B" command).
64 Appendices Codepage 874 (Thai) Codepage 1251 (Cyrillic) Codepage 1252 (Latin-1) Codepage 1257 (Baltic)
C Colour Scantech-ID Shuttle SG-15 65 APPENDIX D FACTORY DEFAULT SETTINGS Currently, the Factory Default Settings are as follows: IP Address 192.168.3.227 Subnet mask 255.255.255.0 Default Gateway 192.168.3.250 IP Address Remote Host 192.168.3.
66 Appendices APPENDIX E UPDATING APPLICATIONS OR SYSTEM PACKAGES Here you find the procedure to update Application or System Packages: Step Explanation 1 Login on the SG-15 and navigate to the Package Manager page 2 Choose File 3 Locate the file [name]_[version]_ armhf.
C Colour Scantech-ID Shuttle SG-15 APPENDIX G 67 FREQUENTLY ASKED QUESTIONS INDEX G-1 1. General 2. SG-15Colour Configuration and the SG-15Colour User's Manual 3. Networking 4. Demo-possibilities and how to get started 5. Barcodes GENERAL What is the standard available configuration and looks for the ShuttleC? See Appendix J. Can we have other colours than black, Silver or Red? Yes, other colours are only available on request, only in large quantities and under specific conditions.
68 G-2 Appendices Colour SG-15 CONFIGURATION AND THE SG-15Colour USER’S MANUAL How do I configure the ShuttleC? See chapter 5. The SG-15Colour has an internal web server, which makes it possible to configure it using any internet browser. Where do I find the most recent ShuttleC Command Set? In this manual (Appendix B) and on the Product Support Library.
C Colour Scantech-ID Shuttle SG-15 G-4 69 DEMO POSSIBILITIES & HOW TO GET STARTED What kind of development package does the system-integrator get from Scantech-ID? C The Shuttle Product Support Library contains lots of technical information and free source code examples in all popular languages.
70 Appendices
C Colour Scantech-ID Shuttle SG-15 H 71 C SHUTTLE PROJECT TASKS C The integration of a Price Checker like the Shuttle into a store IT system is slightly more complex than linking a mouse to your PC. Therefore you find below -to prevent any miscommunication- a general guideline describing “Who Does What While Launching A ShuttleC Project”. Scantech supplies: ShuttleC Hardware Configuration (excl. network cabling). Overview of possibilities, features and benefits of the ShuttleC.
72 Appendices APPENDIX I TECHNICAL SPECIFICATIONS Electrical Power supply voltage Power consumption ShuttleC DC input Interfaces 100-240 VAC 50/60 Hz through external PSU (adapter) or Power over Ethernet complying IEEE 802.3af (optional) 3.25 Watt (5Vdc, 650 mA). At nominal configuration: Omni laser scanner and Ethernet interface. USB port unused. +5 V Standard Ethernet, Wireless IEEE 802.11 a/b/g/n/ac (optional) or Power over Ethernet IEEE 802.
C Colour Scantech-ID Shuttle SG-15 73 System Architecture ARM Cortex-A7 Dual-Core Processor Operating System Standard Linux (Kernel > 3.0) 2GB expandable with USB flash drive and SD card Memory Flash 512MB Memory RAM Client Applications included Software Environmental Operating temperature Humidity Safety/EMC Laser Safety 0°C … 40°C 20% .. 95% RH (non condensing) IEC 825-1 (1993) Class I, U.S. 21CFR1040 Class IIa Electrical Safety IEC 60950-01 and/or EN 60950-1, CAN/CSA C22.2 No.
74 Appendices APPENDIX J OVERVIEW PARTNUMBERS C Shuttle with Omni-Directional Laser -MICA- Scanner C Shuttle with Single Line -CCD- Scanner Standard version with Ethernet: Standard version with Ethernet: 1. 718A7 G0104 E2000 2. 718A7 00404 E4000 3. 718A7 00300 E0000 1. 718A7 20104 E2000 2. 718A7 20404 E4000 3. 718A7 20304 E0000 Black Ethernet Silver Ethernet Red Ethernet Black Ethernet Silver Ethernet Red Ethernet Wireless LAN: Wireless LAN: 4. 718A7 00104 W2000 Black WLAN 5.
C Colour Scantech-ID Shuttle SG-15 75 C APPENDIX K SHUTTLE DEMONSTRATION PROGRAM C The Shuttle demonstration program SG15Demo.exe can be found in the Product Support Library (directory \Demonstration Tool). This program can be used for quick and easy demonstrations or for experimenting. You can see literally, what is sent to an SG-15Colour or what is received from it. Just connect to your SG-15Colour and try it.
76 Appendices You can also give SG-15Colour Control (ESC) commands. Just hit the ESC key, which sends an actual esc-character (0x1b). Examples: Colour Clear the SG-15 screen: Hit 'ESC' key Enter '%' C Kick the Shuttle into Sleep Hit 'ESC' key Enter @ Make the speaker sound Hit ESC key Enter ^ Wake up the ShuttleC again Hit ‘ESC’ key Enter Capital A Consult Appendix B for more ESC command examples. When you scan a barcode at the SG-15Colour, the program responds with 1 of 5 predefined texts.
C Colour Scantech-ID Shuttle SG-15 APPENDIX L 77 WiFi info Colour A short note on this SG-15 WiFi version: To bring the SG-15 up to date regarding WiFi connectivity and to achieve the following goals: • Support of modern 2016+ WiFi standard IEEE 802.11 a/b/g/n/ac • More compact, less components and energy • Use latest technology also applied in modern tablets and PC's • Better continuity and long term availability, the SG-15 WiFi technology is now soldered directly on the motherboard.
78 Appendices Appendix N Colour SG-15 Control Bar Codes Colour To make live easier for those who test, install and maintain the SG-15 we have implemented four Control Barcodes in the Shuttle: , Reboot: Back to Default: Will reboot the SG-15Plus Load default parameter set *1 Reboot to LAN: Show the SG-15 status • For WiFi testing purposes only. See explanation on the next page. • Reboots the SG-15 using LAN as the active interface to configure a WiFi unit.
C Colour Scantech-ID Shuttle SG-15 *1 79 Showing the SG-15 status The Shuttle+ Price Checker is a kind of black box -from the outside-, where it concerns the primary network parameters. In order to make Installation and Service easier, the Terminal Status Request by Bar Code feature has been implemented. With the ultimate goal to decrease the Total Cost of Ownership. How does it work: • Scanning this barcode at the ShuttleC will show its status and configuration info.
80 Appendices
C Colour Scantech-ID Shuttle SG-15 81 Appendix P Drilling Template for Easy Mounting ( Drilling Pattern ) • Print/Enlarge this page to the real product sizes of 182 X 131 mm • Make sure the scaling reference of 100 mm is respected.
82 Appendices
C Colour Scantech-ID Shuttle SG-15 83 Colour Appendix Q Product Summary What's new at the SG-15 Here is an overview of our objectives and the new major product characteristics: 1. Color screen 3.5" TFT-LCD 320X240 resolution. 16 million colours for high quality displaying. Wide viewing angle. A big step forward in readability. SG-15 and SG-15 Plus Colour SG-15 2. 3. 4.
84 Appendices
C Colour Scantech-ID Shuttle SG-15 85
86 Appendices Scantech-ID BV Heliumweg 34 A 3812 RE Amersfoort The Netherlands Phone: E-mail: Internet: +31 (0)33 469 84 00 info@scantech-id.com www.scantech-id.com www.champtek.