The Federal Communication Commission Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication.
Copyright © 2015 This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of maker. Note: Due to product improvement programs, specifications and features are subject to change without prior notice.
Contents Chapter 1. Introduction ................................................................................................4 1.1 Safety & Caution .............................................................................................5 1.2 Package ............................................................................................................6 1.3 Scanner Characteristics ..................................................................................7 Chapter 2. 2.
FCC Approval This device has been tested in accordance with the procedures and in compliance with Part 15 Subpart B of FCC Rules and keeps all requirements according ANSI C63.4 & FCC Part 15 B Regulation and CISPR22 Class B.
Chapter 1. Introduction This barcode scanner is a brand new compact design which is especially for the applications in ticketing, stocktaking or logistic market. With its tiny and lightweight body, it can be easily carried in pocket or bag for mobility application. As the tiny compact body, the housing is designed with IP54 rating that prevents from water and dust and 1.5M dropping resistance. In addition, it can easily connect to the most mobile devices via Bluetooth technology on android and iOS system.
1.1 Safety & Caution Please read the following safety statements carefully. 1. Please preserve this user’s manual for reference. 2. Before cleaning the equipment, the power must be cut off. Do not use liquid or spray type of detersive to clean the equipment. Please use dampish cotton cloth to clean the equipment. 3. Keep the equipment dry to avoid short circuit. 4. During installation the equipment must be fixed at solid table to avoid damage caused by falling. 5.
1.2 Package Unpack the scanner as follows: Take the scanner and accessories out of the box. Remove the packing materials. Check the packing list to make sure all the items ordered are received. Barcode Scanner USB Cable Neck Strap Battery Quick Guide Adaptor (Option) Visually inspect the scanner and accessories for any evidence of physical damage. If anything is missing or appears to be damaged, immediately contact your dealer.
1.3 Scanner Characteristics The scanner comes with 3 controls buttons and 1 indication LED. The exterior control and display are shown below. Power OFF LED Indicator UP/DOWN Scrolling Buttons OLED Display Micro USB (300 Series) Connector OK/ Power ON For Neck Strap /Trigger Button Reboot *300 series are including the OLED display but 200 series are not.
Chapter 2. Operating the Scanner 2.1 Getting Started The barcode scanner provides the easy-use control buttons and easy-read signal for user scanning experience. The following will give a guide to start with this scanner. 2.1.1 Attach Neck Strap It is recommended to attach the neck strap to the barcode scanner and wearing it on either neck or hand for a convenient and safety carry. 2.1.2 Charge Battery The barcode scanner is installed with a high capacity Lithium battery.
TRIGGER/OK key and point the red beam fully across the barcodes. The following are examples. V V 2.4 V Correct Scanning X Acceptable Scanning Acceptable Scanning Incorrect Scanning Enter Scanner Menu The scanner can be configured by scrolling control buttons. Press the UP and DOWN buttons or Down button 3~5 sec simultaneously to access the scanner configuration menu. View Data System Setting BT Configure . Return BT Service Data Process The menu and functions are listed as the below table.
BT Service Auto Connect(HID) Enable/Disable ◎ ◎ MAC Address 12 Characters Bluetooth MAC Address ◎ ◎ BT Version Bluetooth Firmware Version ◎ ◎ Wake up Nulls Enable/Disable ◎ ◎ Power ON/OFF Enable/Disable ◎ ◎ Pairing Pairing neighboring Bluetooth devices ◎ ◎ Connect to Last Dev View Connect to Bluetooth device ◎ ◎ Store Mode Send Only / Send & Store /Store Only ◎ ◎ Avoid Same Code Enable/Disable ◎ ◎ Data Process Memory Status System Setting Reset Memory Auto Erase Indicates: Sc
Sleep Timeout Disable, 1 sec to 5 minutes(3 minutes) ◎ ◎ Set Date/Time YYYY:MM:DD & HH:MM:SS ◎ ◎ Battery Status Level of the Battery Status Indicator Scanner FW Ver.
2.4.1 View Data Menu The scanned barcodes can be reviewed by selecting View Data. On the top menu, press UP or DOWN to select “View Data”. View Data BT Configure BT Service Data Process Press UP or DOWN to review the scanned barcodes. D150101 000720 4710088123456 UP/DN - search OK 3sec - del To delete this item, press OK for 3 seconds. The further messages show up. D150101 000720 4710088123456 UP - del DN - cancel Press UP to confirm deletion. Press DOWN to return to data review. 2.4.
The “BT Configure” sub-menu is as following. Connect Profile Wakeup Nulls Auto Connect . . Return MAC Address BT Version 2.4.2.1 Connect Profile Select “Connect Profile” to set BT connection as HID or SPP. Connect Profile HID UP/DN - change OK - confirm HID SPP For iOS, select HID only. If select SPP, install App on the mobile phone or tablet is required. 2.4.2.2 Auto Connect Select “Auto Connect” to decide if the BT can automatically connect upon available.
2.4.2.4 BT Version Select “BT Version” to check the BT firmware version. BT FW Version: HID-SPP-AT-V1 00-T029BT-201 41208 BT FW Version Press any keys to return to the upper menu. 2.4.2.5 Wakeup Nulls Select “Wakeup Nulls” to select if send ‘Null’ to the host when scanner wakes up. Wakeup Nulls Disable UP/DN - change Wakeup Nulls EN OK - confirm Wakeup Nulls DIS Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.
2.4.3.1 Power ON/OFF Select “Power ON/OFF” to set Bluetooth connection on or off. Power ON/OFF Disable UP/DN - change OK - confirm Power EN Power DIS Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.3.2 Pairing Select “Pairing” to connect the scanner to mobile phone or tablet. BT Pairing OK - confirm BT Pairing 2.4.3.3 Connect Last Dev Select “Connecting to” to pair the last connected device.
2.4.4 Data Process Menu On the top menu, select “Data Process” for advanced data configuration. View Data BT Configure BT Service Data Process The sub-menu is as following. Store Mode Repeat Code . . Return 2.4.4.1 Store Mode On the “Data Process” sub-menu, select “Store Mode” for following options. Store Mode Send & Store UP/DN - change OK - confirm Send & Store EN Store EN Send & Store: Send the scanned barcodes to host and store the barcodes in scanner memory simultaneously.
Avoid Same Code Disable UP/DN - change OK - confirm AvoidSameCode EN AvoidSameCode Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.5 System Setting On the top menu, select “System Setting” for other system settings. System Setting . Return The settings in “System Setting” are listed below.
are available. Press OK to return to upper menu. 2.4.5.2 Reset Memory On the sub-menu, select “Reset Memory” to reset the memory counters. Reset Memory UP - reset OK - cancel Reset Memory EN Press UP to reset the counters. 2.4.5.3 Auto Erase On the sub-menu, select “Auto Erase” to erase all the saved items in memory automatically when the items reach 100,000. A message will prompt before erasing. Auto Erase Disable UP/DN - change OK - confirm Auto Erase EN Auto Erase DIS 2.4.5.
D:2015/01/30 T:14:10:45 UP - set OK - shift Press OK to shift the position. Press UP or DOWN to increase or decrease the date or time. 2.4.5.6 Battery Status On the sub-menu, select “Battery Status” to check the battery capacity. Battery Status OK - return Press OK to return previous menu. 2.4.5.7 Scanner Version On the sub-menu, select “Scanner Version” to check the firmware version. M3CV1.CCD__ 01.06 20150626 OK - return Scanner version Press OK to return to the previous menu. 2.4.5.
2.4.5.9 Vibration On the sub-menu, select “Vibration” to set if vibrating when scanning barcodes. Vibration Disable UP/DN - change Vibration EN OK - confirm Vibration DIS Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.5.10 Auto Exit On the sub-menu, select “Auto Exit” to set auto exit the screen menu. Auto Exit Enable UP/DN - change OK - confirm Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.5.
2.4.5.12 Menu Scrolling On the sub-menu, select “Menu Scrolling” to set whether the scanner menu is scrolling when pressing UP/DOWN and reaching the last item. Menu Scrolling Disable UP/DN - change OK - confirm Press UP or DOWN to set disable or enable. Press OK to confirm. 2.4.5.13 Brightness On the sub-menu, select “Brightness” to set the LCD brightness. Brightness Level 08 UP/DN - change OK - confirm The brightness is ranged from level 1 to level 15. Press UP or DOWN to set the level.
after scanning. Scan Review Disable UP/DN - change OK - confirm Press UP or DOWN to set disable or enable. Press OK to confirm.
2.5 LED Status The LED on scanner shows different color to indicate charging and scanning status. Refer to the table below for LED status.
3.2 Download App Use the mobile device and open browser to visit Google Play. In the input box, type “OEM Pocket Scanner” to search the app. Click “INSTALL” to install it on the mobile device. This version of app is for Android mobile devices. 3.3 Configure Scanner Prior to connecting scanner to the mobile devices, the settings on the scanner should be configured. On the scanner, press UP and DOWN buttons simultaneously to enter configuration menu. Select BT Configure -> Connect Profile -> SPP.
3.4 Pairing The following steps show the pairing steps for the scanner and mobile device. a. Turn on Bluetooth power on mobile device. b. Discover the searching devices shown on mobile device. Find “Pocket Scanner” and click “Pair” to connect the scanner with mobile device by Bluetooth. c. When paired, the scanner will be shown as paired device on mobile device.
3.5 App Main Screen In the App list, click “Pocket Scanner” to execute the scanner application program. Down from Google Play Search “oem pocket scanner” The main screen looks like this. On the screen top shows the product name, connection status and app version. Connect Button: Connect app to the scanner. Synchronize: Upload the data from scanner to mobile device. Send Sync. data: Send out the uploaded data to the designated email address.
3.6 Connect Scanner To connect the app with mobile device, follow the steps below. 2 1 3 4 1. Press “Connect” 2. Wait for a while 3. When connected, the scanner is shown on the device list 4. On the screen top, the connection status shows “Connected”.
3.7 Synchronize the Data From Scanner The scanned data can be saved in the barcode scanner and the data can be uploaded to the mobile devices. Follow the steps below. 2 1 3 4 5 1. Press “Synchronize” to upload all the data from scanner to mobile device. 2. Select the corresponding scanner. 3. Wait for a while when data is transferring. 4. Select a program to display the data. 5. All the scanned data is shown in the program.
3.8 Send the Synchronized Data Save the uploaded data from scanner as a file in the mobile devices. This file can be sent out to the designated email address. Therefore the data can be downloaded from PC or other equipment in order to do further data process on other PC’s or equipment. Follow the steps below. 2 1 abc@hello.com 3 1. Press “Send Sync. data” to send out the data file. 2. The mobile devices will pop up email options.
3.9 Data Format Setting The data shown in mobile devices can be formatted prior to upload the data from scanner. Therefore required data format can be used in the mobile devices. On the main screen, press “Setting” to enter the menu. The options in “Setting” are shown as following.
The data format to be configured is defined as following.
Row Separator: Select one the separators between 2 rows. Email: Set the email address here for the data file to be sent to. When press “Send Sync. data” to send out the file, the email address will be automatically prompted. No need to type it afterwards.
3.10 Synchronize the Date and Time The data and time on the scanner can be set by “Date/Time Synchronization”, according to the mobile devices. Follow the steps below. 1 2 1. Press “Date/Time Synchronization”. The date and time in the scanner will be set according to the mobile devices. 2. When success, the message shows “Set date time complete”.
Appendix 1 -Configuration Flow Chart(Pocket Scanner) ①Scan Start of Configuration ②Scan all necessary labels for parameters that meet applications Interface Selection Connection Selection Symbologies Selection ③Scan End & Save Parameter to permanently save the settings by your programmed.
Appendix 2 - Setting Barcode (1) HID SPP Auto Connect(HID) Enable Auto Connect(HID) Disable BT MAC Address BT Versioin Wakeup Nulls Enable Wakeup Nulls Disable BT Power ON BT Power OFF BT Pairing BT Connect Last Device [Store Mode]Send & Store [Store Mode]Store Only
Appendix 3 - Setting Barcode(2) [Store Mode]Send Only Reset Memory Avoid Same Code Enable Avoid Same Code Disable Auto Erase Enable Auto Erase Disable Memory Status Sleep Timeout 1 sec Sleep Timeout 5 sec Sleep Timeout 10 sec Sleep Timeout 30 sec Sleep Timeout 1 min Sleep Timeout 2 min Sleep Timeout 3 min
Appendix 4 - Setting Barcode(3) Sleep Timeout 5 min Scanner Version Engine Version BT Versioin Beep ON Beep OFF Vibration ON Vibration OFF [Data Format] Time&Battery& Code [Data Format]Memory & Code [Data Format]Code Only Factory Default Scan Review ON(300 series) Scan Review OFF(300 series)