Owner's Manual

ManualsBrandsChamberlain ManualsAccessoriesChamberlain CLULP1

White Grey Red

Wire Nut

Connection

Wire

White

Connection

Wire

White/Black

Connection

Wire

Parking Assist

Wires

Safety

Reversing

Sensor Wires

Insert Into Appropriate Terminals

Parking Assist

Wires

120 Vac Power Adapter

White (-)

White/Black (+)

Wire

Nuts

Model CLULP1

Chamberlain Laser Garage Parking Assist

Owner’s Manual

To avoid eye INJURY or damage to product:

• NEVER point the laser at anyone.

• NEVER look directly into the laser beam.

• NEVER disassemble the laser.

• The parking assist is NOT a substitute for safe parking practices.

• Use of controls or adjustments, or the performance or procedures

other than specified can result in hazardous radiation exposure.

• ONLY for use on Chamberlain manufactured garage door openers.

WARNING

CAUTION

WARNING

Figure 1

Figure 3A

Figure 3B

Insert into appropriate terminals

Red White Grey

Parking Assist Wires

Safety Reversing

Sensor Wires

Parking Assist Wires

120 Vac Power Adapter

White (-)

White/Black (+)

Figure 2B

INSTALLATION

1. Open your garage door and park your vehicle outside of garage.

2. Determine the mounting location on the ceiling and fasten the

parking assist using screw and anchor (Figure 1).

3. For installation on a Chamberlain garage door opener:

Locate the quick connect terminals on your motor head.

Temporarily remove the wires for the safety reversing sensors

(see your owner’s manual for the location of the quick connect

terminals.). The power adapter will not be needed, discard it.

For all other installations (power adapter required):

Locate the nearest 120 Vac power outlet to the parking assist(s).

Route wires from parking assist(s) to outlet. The power adapter

is intended to be correctly oriented in a vertical or floor

mount position.

4. Stripping the wires prior to installation:

Installing one parking assist: Separate white and white/black

wires and strip 7/16" (11 mm) of insulation from parking assist

wires.

Installing two parking assists: Cut 6" (15 cm) of wires from the

end of one set of parking assist wires for use as connection

wires. Separate white and white/black

wires and strip 7/16"

1 mm) of insulation from both ends of connection wire.

5. Connect the wires:

Installing one parking assist (Chamberlain installation): Twist

like colored wires for parking assist and safety reversing sensors

together. Insert twisted wires into quick-connect holes: white to

white and white/black to grey* (Figure 2A).

Installing one parking assist (all other installations): Connect

wires from parking assist to power adapter as shown (Figure 2B).

Plug power adapter into 120 Vac outlet.

Installing two parking assists (Chamberlain installation):

Separate white and white/black wires and strip 7/16" (11 mm) of

insulation from the end of parking assist wires. Twist like colored

wires for parking assists, safety reversing sensors and

connection wire together. Secure with wire nut. Insert connection

wires into quick-connect holes: white to white and white/black to

grey* (Figure 3A).

Installing two parking assists (all other installations): Twist

like colored w

ires from parking assists and connection wires

together

. Secure with wire nut and attach connection wires to

power adapter as shown (Figure 3B). Plug power adapter into

120 Vac outlet.

* Please refer to your garage door opener owner’s manual for

proper wire installation.

CAUTION

ATTENTION

132C2469-1

LASER RADIATION

DO NOT STARE INTO BEAM

RAYONNEMENT LASER

NE PAS REGARDER DIRECTEMENT

LE RAYONNEMENT LASER

Maximum power output: < 1mW @ 635 - 670nm

Puissance de sortie maximum: < 1mW @ 635 - 670nm

CLASS II LASER PRODUCT

APPAREIL AU LASER DE CLASSE II

This Class B digital

apparatus complies

with ICES-003.

Wire Nut (2)

Parking Assist

Screw 6ABX1-1/4"

Anchor

120 Vac Power Adapter

CARTON INVENTORY

Figure 2A

Summary of content (4 pages)

PAGE 1
® Model CLULP1 Chamberlain Laser Garage Parking Assist WARNING Owner’s Manual CARTON INVENTORY Anchor CAUTION Wire Nut (2) Screw 6ABX1-1/4" Parking Assist To avoid eye INJURY or damage to product: • NEVER point the laser at anyone. • NEVER look directly into the laser beam. • NEVER disassemble the laser. • The parking assist is NOT a substitute for safe parking practices.
PAGE 2
SET UP AND ADJUSTMENT Figure 4 1. Drive your vehicle into garage and park in the desired location. 2. Activate the parking assist by obstructing the path of the safety reversing sensors. The laser will emit a pulsing bright red beam (Figure 4). Aim the red beam to a location on the dash or hood that can easily be seen while seated in the driver’s seat. NOTE: The laser will automatically deactivate after approximately one minute for Chamberlain garage door openers.
PAGE 3
® Asistente de estacionamiento de garaje láser Chamberlain modelo CLULP1 WARNING Manual del propietario INVENTARIO DEL PAQUETE Empalme para cables Tornillo 6ABX 1-1/4" Asistente de estacionamiento Adaptador de energía de 120 VCA INSTALACIÓN 1. Abra la puerta del garaje y estacione el vehículo fuera del garaje. 2. Determine la ubicación de montaje en el techo y fije el asistente de estacionamiento utilizando un tornillo y un taquete (Figura 1).
PAGE 4
CONFIGURACIÓN Y AJUSTE Figura 4 1. Conduzca el vehículo hacia el garaje y estaciónelo en el lugar deseado. 2. Active el asistente de estacionamiento obstruyendo el camino de los sensores de reversa de seguridad. El láser emitirá un haz rojo brillante intermitente (Figura 4). Apunte el haz rojo hacia un punto en el tablero o en el cofre que pueda percibir fácilmente mientras está sentado en el asiento del conductor.