Quick Start Manual

ManualsBrandsChamberlain ManualsAccessoriesChamberlain BIK01

Position the garage door opener

Introduction

Overview

NOTE: A 2x4 is ideal for setting the distance between

the rail and the door. If the ladder is not tall enough

you will need help at this point.

Remove any packing material and lift the garage

door opener onto a ladder. Fully open the door

and place a 2x4 (laid flat) under the rail. For

one-piece doors without tracks, lay the 2x4 on

its side.

One-piece door

without tracks

All other

door types

The Installation Upgrade Kit includes all components needed to hang garage door openers up to 24" from

the ceiling. The Installation Upgrade Kit works with ANY BRAND of garage door opener and gives openers a

ﬁ nished look using premium components, hardware, and wire management. Vibration Isolator Bolts are also

included to make even the quietest garage door openers more silent within the home.

To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door.

INSTALLATION UPGRADE KIT • MODEL BIK01

(A) 32" Support

Bracket (1)

(B) 32" Angled

Bracket Shields (2)

(D) 24" Hanging

Brackets (2)

(H) Lag Screw 1-7/8" (2) (K) Hex Bolt 5/16"-18 x 7/8" (2)

(F) Lock Washer (6)

Ladder

Tape Measure

Hacksaw

Adjustable Crescent

Wrench

Socket Wrench and

7/16" and 1/2" Sockets

Drill with Phillips Screw

Bit and 5/16" bit

(G) Nut

5/16"-18 (6)

(J) Self-Threading

Screw (4)

(I) Double Sided Tape (4)

(E) Vibration Isolation Bolts 5/16"-18 (2)

CARTON INVENTORY:

TOOLS NEEDED:

Assemble and install the garage door opener in accordance with the manufacturer’s instructions but STOP before positioning the garage door opener. Carefully and

safely remove all existing hanging brackets and hardware used with the previously installed garage door opener.

Summary of content (4 pages)

PAGE 1
INSTALLATION UPGRADE KIT • MODEL BIK01 The Installation Upgrade Kit includes all components needed to hang garage door openers up to 24" from the ceiling. The Installation Upgrade Kit works with ANY BRAND of garage door opener and gives openers a ﬁnished look using premium components, hardware, and wire management. Vibration Isolator Bolts are also included to make even the quietest garage door openers more silent within the home.
PAGE 2
3 Hang the garage door opener Hanging the garage door opener will vary depending on your garage. Your installation may be different. For ALL installations the garage door opener MUST be connected to structural supports. 3.1 Use lag screws (H) to attach the support 3.2 Make sure the garage door opener is aligned with the header bracket. Measure the distance from each 3.3 Insert the vibration isolation bolts (E) into side of the garage door opener to the support bracket.
PAGE 3
JUEGO DE INSTALACIÓN MODIFICADA • MODELO BIK01 El juego de instalación tiene todos los componentes necesarios para colgar el abre-puerta a una altura de hasta 60 cm (24 pulg.) del techo. El juego de instalación es compatible con CUALQUIER MARCA de abre-puerta de garaje. Tiene componentes y accesorios de primer nivel que le conﬁeren un aspecto de reﬁnada terminación. Contiene pernos amortiguadores de vibración que hacen aún más silencioso al más silencioso de los abre-puertas.
PAGE 4
3 ADVERTENCIA Colgar el abre-puerta del garaje Para evitar la posibilidad de una LESIÓN GRAVE si se cayera el abre-puertas de garaje, sujételo FIRMEMENTE a los soportes estructurales del garaje. Se DEBEN usar anclajes para concreto si alguno de los soportes se va a instalar en mampostería. El montaje del abre-puerta puede variar según la estructura del garaje, por ello, la instalación en su caso podría ser diferente.