User's Manual

ManualsBrandsChamberlain Wireless Products ManualsElectronicsULTRX900R - Extreme Range Transceiver

Carton Inventory

Overview

The Ultra RX - Extreme Range Receiver has a

10-24Vac/Vdc operation with low power consumption

(150 ua). The Receiver has 4 Channels, 2 Transistors

and 2 Relays. The Receiver can control up to

4 devices.

Receiver

Model ULTRX900R

Ultra RX - Extreme Range Receiver

Setup

1 3 2 4 5 6 7 8 9 10 11 12 13

10-24 Vac

1 3 2 4 5 6 7 8 9 10 11 12 13

10-24 Vdc

NOTE: Polarity does not matter.

Power Connections

Relay Outputs

The Receiver has 2 Relays and 2 Transistor (Open

Collector) Outputs to control up to 4 devices.

Higher Amperage (10 amp) applications that are

directly controlled, should use Relay Channels 1

and 2.

Relay 1:

11: Common

12: Ch 1 Normal Open

13: Ch 1 Normal Closed

1 3 2 4 5 6 7 8 9 10 11 12 13

Relay 2:

8: Common

9: Ch 2 Normal Open

10: Ch 2 Normal Closed

Lower Amperage (500 ma or lower) applications that

are indirectly controlled, should use Transistor Output

Channels 3 and 4.

Channel 3:

Terminal 6

Channel 4:

Terminal 4

1 3 2 4 5 6 7 8 9 10 11 12 13

Dipswitch Settings

NOTE: If using the Receiver with a Gate Control Unit

(GCU) proceed to Program with Gate Control Unit

(GCU).

NOTE: The Dipswitches on the

Receiver can be accessed by

removing the screw on the

bottom of the Receiver.

Ensure the Receiver does

not have power. Set

Dipswitch #1 to the ON

position.

NOTE: These steps apply only if more than one

Receiver is being used.

Step 1: Ensure the

Receiver does not have

power. Set Dipswitch #1 to

the ON position in each

Receiver.

Step 2: Set the Identity of each additional Receiver

by changing the Dipswitches as shown in the chart

below.

Receiver ID Switch #2 Switch #3

2 ON OFF

3 OFF ON

4ON ON

Additional Receivers

NOTE: Do not connect power until instructed to do so.

Summary of content (4 pages)

PAGE 1
Model ULTRX900R Ultra RX - Extreme Range Receiver Overview Relay 2: 8: Common 9: Ch 2 Normal Open 10: Ch 2 Normal Closed The Ultra RX - Extreme Range Receiver has a 10-24Vac/Vdc operation with low power consumption (150 ua). The Receiver has 4 Channels, 2 Transistors and 2 Relays. The Receiver can control up to 4 devices. 1 2 3 4 5 6 7 8 9 10 11 12 13 Lower Amperage (500 ma or lower) applications that are indirectly controlled, should use Transistor Output Channels 3 and 4.
PAGE 2
Output Timing Program with Gate Control Unit (GCU) Channel 1: Dipswitch #4 OFF ON OFF ON Dipswitch #5 OFF OFF ON ON Time NOTE: The Dipswitches on the Receiver can be accessed by removing the screw on the bottom of the Receiver. 0.5 Sec 5 Sec 1 Min Toggle Output Timing Channel 2: Dipswitch #6 OFF ON OFF ON Channel 1: Dipswitch #7 OFF OFF ON ON Time Dipswitch #4 OFF ON OFF ON 0.5 Sec 5 Sec 1 Min Toggle Dipswitch #5 OFF OFF ON ON Time 0.
PAGE 3
Program Accessories Door Strike or Magnetic Lock Single Pushbutton Control (WPB1LM) Step 1: Connect relays (as shown in Setup: Relay Outputs and the charts below). NOTE: If a Door Strike is used, a separate power supply is required. If a Magnetic Lock is used, use the Normally Closed connections (see below). GCU Optional external power input 10-24 Vac or DC + DC AC Step 1: Connect relays (as shown in Setup: Relay Outputs). Step 2: Connect power (as shown in Setup: Power Connections).
PAGE 4
Operation 114A3549 © 2007, The Chamberlain Group Inc. All Rights Reserved 7 NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.