User's Manual

Universal Radio Control
OWNERS MANUAL
With SECURITY✚, the code between the remote control and
the receiver changes with each use, accessing over 100 billion
new codes.
You can activate your opener with several SECURITY✚ remote
controls (with yellow indicator lights) utilizing up to 8 functions,
and one SECURITY✚ Keyless Entry.
Transformer Model 85 may be required if your garage door
opener is a brand other than Lift-Master, Chamberlain or
Sears.
NOTE: Model 535-2LM is factory pre-set with matching
receiver and remote control codes.
IMPORTANT: For maximum security and range, you must
disable the existing radio on your opener, otherwise it
could still activate your opener:
• If there is an external receiver, disconnect power to it.
• If it is an integrated receiver, either clip off the component
that feeds power to the receiver
or remove the tuning slug
and antenna from the receiver section.
• If you have a Lift-Master, Sears or Chamberlain opener with a
“SMART” receiver, erase the old codes by holding down the
Smart button for 6 seconds until the indicator light turns off.
• If you have code switches, reset them to a random code and
deactivate the receiver by removing the tuning slug and
antenna.
THE RECEIVER MAY BE INSTALLED IN ONE OF TWO WAYS:
1. Mounted directly on the door opener with clips provided as
shown on page one.
2. Attached to an inside wall of the garage with connecting bell
wire (not supplied) as shown on page two.
When installing two or more receivers in a garage, position
them at least 10 feet apart to prevent electronic interference.
MOUNTING RECEIVER ON A COMMERCIAL OPENER
Fully extend antenna wire below bottom of case as shown.
Loosen the three terminal screws on the receiver (labeled 1, 2
and 3). Insert one end of a mounting clip under each terminal.
Do not retighten at this time.
Loosen the three terminal screws on the opener used for push
button controls and radio power.
Leaving the push button bell wire in place, insert the other ends
of the mounting clips under the opener terminal screws.
NOTE: If the number sequence of opener terminals
doesn't match the receiver, turn the receiver around (so
back is facing out) and complete the connection.
Retighten the terminal screws on opener and receiver.
Reconnect power to the opener. The receiver push bar should
light. If it does not, use Transformer Model 85.
Model 535LM Security✚
Receiver Only
Model 535-2LM Security✚
(With 2 Remote Controls)
MOUNTING ON RESIDENTIAL OPENERS
Use a 2 wire connection
only. Attach mounting clips to receiver
terminals 1 and 2, and to the opener terminals used for push
button controls. Plug the transformer into the receiver as
shown, and into a 120 Volt outlet.
Side two contains wall mounting instructions and code setting
instructions.
Children operating or playing with a garage door
opener can injure themselves and others.
The garage
door could close and cause serious injury or death.
Do
not allow children to operate the push buttons or the
remote control transmitters.
Install the receiver (and any additional push buttons)
out of the reach of children and away from all moving
parts of the door and door hardware, but
where the
garage door is visible.
A moving garage door could injure someone under it.
Activate the opener only when the door is properly
adjusted, you can see it clearly, and there are no
obstructions to door travel.
WARNING
Disconnect power to the garage door opener before
installing the receiver.
ING
WARNING
To Outlet
Model 85
Transformer
OPENER
TERMINALS
Receiver
Terminals
Antenna Wire Fully Extended
Mounting
Clip #1
Mounting
Clip #2
Mounting
Clip #3
Common
Push Button
Radio Power
©
To comply with FCC/IC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and replacing the
transmitter battery. THERE ARE NO USER SERVICEABLE PARTS.
NOTICE TO U. S. CONSUMERS:
Some states prohibit the service or repair of garage door openers which
cannot be made to comply with the safety standards contained in UL
325 (1988 revision). In order to comply with both the letter and the spirit
of these laws, this universal radio control should not be used with any
Lift-Master
®
, Chamberlain
®
, or Sears Craftsman
®
garage door opener
manufactured prior to April 1, 1982. To find out if your Chamberlain-
made garage door opener was manufactured prior to or after April 1,
1982, please call 1-800-528-9131 before installing this universal radio
control.