SHENZHEN CHAINWAY INFORMATION TECHNOLOGY CO.
Statement 2013 by ShenZhen Chainway Information Technology Co., Ltd. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission written from Chainway. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.The software is provided strictly on an “as is” basis.
Statement .......................................................................................... 1 Chapter 1 Product Intro ..................................................................... 4 1.1 Intro ..................................................................................... 4 1.2 Interface .............................................................................. 5 1.3 Necessary Parts List............................................................ 6 1.4 Device installation ..
.10 WWAN Specification ............................................................ 27 Chapter 5 SIMPLIFIED EU DECLARATION OF CONFORMITY ..... 28 Chapter 6 Warning ..........................................................................
Chapter 1 Product Intro 1.1 Intro Chainway URA4 is a 4-channel fixed RFID reader, based on Android 9.0. Integrated with Impinj R2000 RFID chip, it supports RS232, RJ45 and HDMI, and can be compatible with various types of antennas.
1.2 Interface Pic.
1.3 Necessary Parts List 1 2 3 4 5 6 7 URA4 reader, 12V power adaptor UHF antenna, 9dBi etc. Feeder line, SMA male side connects with device, interface on other side needs match with antenna.
1.4 Device installation URA4 reader adopts Android operating system, it can be connected with Internet through RJ45, WIFI and 4G etc. And connect with monitor through HDMI cable. Developer could use USB cable to connect device with PC for developing application, device could also be connected with PC through serial port cable. The UHF antenna should install with the professionals, the enduser cannot change the antenna without authorization Pic.
Chapter 2 UHF demo 2.1 Operating Interface Pic.
Connect monitor through HDMI cable and long-press power button for 3 seconds to switch on device. Click demo_uhf icon to enter demo as Pic.4-1, UHF module will initiate as Pic.4-2, if there is no error messages show up, then initiation process has been successfully finished. “init. fail” means UHF module failed to initiate, need to exit application and repeat operation. If initiation cannot successfully finished, need to contact tech support for further. Pic.
Chapter 3 UHF tag scanning Click SCAN on top of navigation bar to enter tags reading page. 3.1 Auto Scanning Select “Auto”, then click “Start” button to start tags scanning circularly, the information such as EPC or TID, Count, RSSI and Ant. number. As Pic.5-1. “filter” button can be used to setup tag which has been filtered, user could setup address, data length to filter tags. EPC, TID and USER areas can be selected, setup data length to 0 and clear EPC list, then click “Setup” to confirm in Pic.5-2.
Pic.
3.2 Single Scanning Select “Single” button and click “Start” to start scanning tag, EPC or TID, Count, RSSI and Ant.number will display on right side, as Pic.53. Pic.
3.3 Read UHF Tag Click “READ” on top of navigation bar to enter page of tag reading. User could read data of 4 areas, RESERVED, EPC, TID and USER, setup address and data length, default password is “00000000”, click “Read” to read tags in Pic.6-1. Pic.
Comment: user could filter tags by setup address, data length and data in EPC, TID and USER areas, select “Enable” button to switch on filter function in Pic.6-2. Pic.
3.4 Write Tag Click “WRITE” on top of navigation bar to enter tag writing page. User could write data in RESERVED, EPC, TID and USER areas, setup start address and data length, input access password and data(hex), click “Write Data” to write data in Pic.7-1. Comment: user could filter tags by setup address, data length and data in EPC, TID and USER areas, select “Enable” button to switch on filter function. Pic.
3.5 Lock Tag Click “LOCK” on top of navigation bar to enter tag locking page. Input access password( DONOT input default password.), then click column of “Lock Code”, it will display window for selecting different methods of locking, click “OK” to generate lock code automatically, then click “Lock” to lock tags in Pic.8-1 and Pic.8-2. Comment: user could filter tags by setup address, data length and data in EPC, TID and USER areas, select “Enable” button to switch on filter function.
Pic.
3.6 Kill Tag Click “KILL” on top of navigation bar to enter operating page. Input access password (DONOT input default password.), click “Kill” button to destroy tags in Pic.9-1. Comment: user could filter tag by setup address, data length and data for selecting EPC, TID or USER area. Pic.
3.7 UHF Module Version Click 3 dots on top right of application and click “About” in list to check version of UHF module in Pic.10-1. Pic.
3.8 Module Temperature Click 3 dots on top right of application, click “Module temperature” in list to check UHF module temperature in Pic.11-1. Pic.
Chapter 4 Config Click “CONFIG” on top of navigation bar to enter setup page. 4.1 Working mode User could setup different frequency band for different countries, as Pic.12-1, click “Set Frequency” to confirm frequency band. Click “Get Frequency” to check current frequency band. Pic.
4.2 Output Power User could select different output power from 5 to 30dBm in Pic.12-2, click “Set Power” to confirm setup. Click “Get Power” to get current output power. Pic.
4.3 R2000 settings Select ANT1-ANT8 to setup antenna, selected antenna will start functioning, unselected antenna will in OFF in Pic.12-3. Click “Set Antenna” to confirm setup, “Get Antenna” to check current antenna status. Pic.
4.4 Protocol There are two protocols can be selected in Pic.12-4, click “Set Protocol” to confirm. Pic.
4.5 RF link There are four parameters can be selected in this parameter, as Pic.12-5. Click “Set link parameter” to confirm, click “Get link parameters” to check current RF link parameters. Pic.
4.6 QT Tag Select “Set QTPara” to switch ON and OFF hidden areas of QT tag, click “Get QTPara” to check current status. Pic.
4.7 Open tagFocus Select ON/OFF of tagFocus in Pic.12-6. 4.8 Open FastID Select ON/OFF of “Open the EPC and TID” in Pic.12-6. 4.9 Open EPC and TID Select ON/OFF of “Open the EPC and TID” in Pic.12-6. 4.10 WWAN Specification WWAN Frequency Band GSM 900 GSM 1800 UMTS B1/B8 LTEB1/B3/B7/B8/B20/28/34/38/40 WLAN Standard Frequency 2.4G WIFI BT 5G WIFI 5.8G WIFI 2.412GHz~2.472GHz 2.402GHz~2.480GHz 5.15GHz~5.35GHz 5.725 GHz -5.
Chapter 5 SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Shenzhen Chainway Information Technology Co.,Ltd. declares that the radio equipment type Fixed Android UHF Reader is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:(www.chainway.net) The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
Chapter 6 Warning CE: RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. FCC: Federal Communication Commission (FCC) Radiation Exposure Statement. When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help.
