FCC ID:2AC6AR6 SHENZHEN CHAINWAY INFORMATION TECHNOLOGY CO.
Content Content .......................................................................................... 1 Statement .......................................................................................... 3 Chapter 1 Product intro ..................................................................... 4 1.1 Intro ..................................................................................... 4 1.2 Precaution before using battery ........................................... 5 1.3 Charger .......
FCC caution This device was tested for typical body‐worn operations with the back of the handset kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly.
Statement 2013 by ShenZhen Chainway Information Technology Co., Ltd. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission written from Chainway. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
Chapter 1 Product intro 1.1 Intro This is a new UHF back clip product, featuring the Cortex-M3 STM32 processor with excellent working performance. The device can be used with any Android and IOS device as a host. The device combines powerful UHF (Read and write) functions with 2D scanning for greater sensitivity. It equipped with a host is widely used in clothing inventory, warehouse management, vehicle management, financial management and other fields.
1.2 Precaution before using battery Do not leave battery unused for long time, no matter it is in device or inventory. If battery has been used for 6 months already, it should be check for charging function or it should be disposed correctly. The lifespan of Li-ion battery is around 2 to 3 years, it can be circularly charged for 300 to 500 times. (One full battery charge period means completely charged and completely discharged.) When Li-ion battery is not in used, it will continue discharge slowly.
1.3 Charger The charger type is GME10D-050200FGu, output voltage/current is 5V DC/2A. The plug considered as disconnect device of adapter.
1.4 Notes Note: Using the incorrect type battery has danger of explosion. Please dispose the used battery according to instructions. Note: Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. Note: The adapter shall be installed near the equipment and shall be easily accessible. Note: The suitable temperature for the product and accessories is 0-10℃ to 50℃.
Chapter 2 Installation instructions 2.
2.2 Battery charge By using USB contact, the original adaptor should be used for charging the device. Make sure not to use other adaptors to charge the device.
2.3 Buttons and function area display R6 Sled reader has 1 power button and 3 indicating lamps.
Chapter 3 Demo Test 3.1 Install demo-uhf-bt (1.0.8) 1. Copy demo-uhf-bt (1.0.8) into internal storage of smart phone or C7x device. 2. Click to install. 3. Click icon to open demo.
3.2 Pairing Device 1. 2. 3. 4. Switch on Bluetooth function of smartphone or C7x device. Power on R6. Click BLUETOOTH in the demo. Click SEARCH to search for Nordic_UART_CW. 5. Click Nordic_UART_CW to connect.
6. After connecting successfully, user could click 3 dots on top right to check UHF version, battery percentage and UHF module temperature.
3.3 UHF Scan Function 1. Click START in demo or pull the trigger on R6, the UHF tags could be read. 2. Click STOP in demo to stop reading of UHF tags. 3. Click CLEAR to clean all EPC information.
3.4 UHF Configuration 1. Click CONFIG in demo to adjust working mode and output power.
3.5 UHF Encryption 1. Click ENCRYPTION to decrypt and encrypt the special zones of UHF tags such as USER, EPC, etc.
3.6 UHF Tag Reading and Writing 1. The storage of one tag has 4 zones: RESERVED, EPC, TID and USER. Normally, the default password is 00000000. And TID zone can only be read, other zones can be read and written.
3.7 UHF Tag Lock and Kill 1. Lock Function: For example. User could try to lock down EPC zone.
2. Kill Function: Kill function can be used to kill the tag permanently. Input the correct access password and click kill.
3.8 Firmware Upgrade 1. Copy the firmware bin. file into internal storage. 2. Click Select file to search for bin. 3. Click Upgrade to upgrade firmware.
3.9 Barcode Scan Test Select BARCODE SCAN in the demo and click SCAN button on the screen to scan barcodes.
Chapter 4 Device characteristic Physical characteristics Size Weight Color Appearance material Product material Battery specification Indicator LED Buzzer Interfaces 153.96x76x129.08mm 445g Black Plastic Plastic 2600mAh/5200mAh Power, Work, Bluetooth Support Micro-USB Performance MCU RAM+ROM Cortex-M3/72 MHz 64M+4G User environment Operating temp. Storage Temp.
Data collection 2D Imager Scanner 1D Symbologies 2D Symbologies SE2707 UPC/EAN, Code128, Code39, Code93, Code11, Interleaved 2 of 5, Discrete 2 of 5, Chinese 2 of 5, Codabar, MSI, RSS, etc. PDF417, MicroPDF417, Composite, RSS, TLC39, Datamatrix, QR code, Micro QR code, Aztec, MaxiCode; Postal Codes: US PostNet, US Planet, UK Postal, Australian Postal, Japan Postal, Dutch Postal (KIX), etc.
