SHENZHEN CHAINWAY INFORMATION TECHNOLOGY CO.
Statement 2013 by ShenZhen Chainway Information Technology Co., Ltd. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission written from Chainway. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
Contents Statement .......................................................................................... 1 Chapter 1 Brief Instruction ................................................................. 4 1.1 Brief Instruction ................................................................... 4 1.2 Precaution Before Using Battery ......................................... 5 Chapter 2 Installation Guide .............................................................. 7 2.1 Appearance ...................
Chapter 7 Device Specifications ......................................................
Chapter 1 Brief Instruction 1.1 Brief Instruction CHAINWAY C90 is our newly-developed rugged handheld computer that exhibits extremely powerful performance. Built with Android 10 OS and Qualcomm high-performance processor, it features vigorous system configuration. With rich functionality features like barcode scanning, sturdy WiFi performance, NFC, front and rear cameras, it possesses the best price versus performance ratio.
1.2 Precaution Before Using Battery Do not leave batteries unused for extended periods of time, either in the product or in storage. When the battery has been unused for 6 months, check the charge status and charge or dispose of the battery as appropriate. The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles, whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully recharged again.
The battery charge time increases significantly. If a battery is stored or otherwise unused for an extended period, be sure to follow the storage instructions in this document. If you do not follow the instructions, and the battery has no charge remaining when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a new battery. Always follow the charging instructions provided with your product.
Chapter 2 Installation Guide 2.1 Appearance The C90 device appearance is as follows.
2.2 Buttons Button Power Button SCAN Volume Function Press and hold to turn the device on or off.
2.3 Micro SD、SIM card Installation User need to install TF card and SIM card according to the slots of card tray as below. Then insert into slot of SIM/TF. 2.4 Battery Charging Use the adapter to charge the battery. Don't use other brands of charger for device.
2.5 Device Power on/off Press the „Power‟ button on side about 3s due to power on/off. And press it shortly to wake up.
Chapter 3 Call Function 3.1 Phone Click this icon . Click the number button to input the numbers. Click the Click the button to confirm and dial. to end the calling.
3.2 Contacts Click „Contacts‟ to open the contacts list. Click “Create new contact” to add the new contact.
3.3 Messaging Click to open the message list. Click to input the content. Click to send the message. Click to add photos, videos.
Chapter 4 Barcode Reader Open the Barcode2D Demo in APP Center and then press the „Scan‟ button to start scanning. Note: Please scan the barcode correctly, otherwise the scanning might be failed.
Chapter 5 RFID Reader(optional) 5.1 NFC Open the “NFC” demo within Appcenter, and then reading and writing information of the tag.
Chapter 6 Other Functions 6.1 PING 1. Open the Ping in Appcenter. 2. Set the Ping parameters and select the internal/external addresses.
6.2 Bluetooth 1. Open the Bluetooth demo in Appcenter and turn on the Bluetooth. 2. Input the content or select the file, then scan the nearby Bluetooth printer and pair them. 3. Select the printer and click „Print‟ to print the content.
6.3 GPS 1. Open the GPS demo in Appcenter and turn on GPS module. 2. Set the GPS parameters and get the GPS data information.
6.4 Volume Settings 1. Open the Volume Setting demo in Appcenter. 2. Set the volumes based on the requirements.
6.5 Sensor 1. 2. Open the Sensor demo in Appcenter. Test the sensor based on the requirements.
6.6 Keyboard 1. Open the Keyboard demo in Appcenter. 2. Set and test the key values of the device.
6.7 Network 1. Open the Network demo in Appcenter. 2. Test the WIFI/Mobile signal based on the requirements.
Chapter 7 Device Specifications Dimensions Physical Parameters 158.5 x 76.0 x 13.1 mm / 6.24 x 2.99 x 0.52 in. Weight 230g / 8.11 oz. (device with battery) Screen 5.7-inch (18:9), IPS LTPS 1440 x 720 Touch Panel Corning Gorilla Glass, multi-touch panel, gloves and wet hands supported Battery Main battery: built-in 5000 mAh Standby: up to 490 hours (only main battery ; WiFi: up to 470h; 4G: up to 440h) Continuous use: over 12 hours (depending on user environment) Charging time: 2.
Interface USB2.0, Type-C, OTG Storage Card Type Maximum Expansion Storage TF card Operating Temperature Storage Temperature Humidity 128GB Environmental Parameters -20 ℃~+50 ℃ -40 ℃~+70 ℃ 5%RH-95%RH (non-condensing) Dropping Survive Multiple 2.0 m / 6.56 ft. drops to the concrete across the operating temperature range Sealing IP67, IEC compliance Tumble Specification 1000 x 0.5 m/1.
WLAN Blueto oth GNSS Support IEEE802.11 a/b/g/n/ac/d/e/h/i/k/r/v/w, 2.4G/5G dual-band, IPV4, IPV6; Support 5G PA Fast roaming: PMKID caching, 802.11r, OKC Operating Channels: 2.4G(channel 1~13), 5G(channel 36,38,40,42,44,46,48,52,56,60,64,100,104,108,112, 116,120,124,128,132,136,140,149,153,157,161,165), depends on local regulations Security and Encryption: WEP, WPA/WPA2-PSK(TKIP and AES), WAPI-PSK—EAP-TTLS,EAP-TLS, PEAPMSCHAPv2, PEAP-LTS, PEAP-GTC, etc. V2.1+EDR,3.0+HS and V4.1+HS, BT5.
Postal, Dutch Postal (KIX),etc. RFID NFC SDK Developing Environment Chainway SDK Programming Language Developing Tool Java Eclipse/Android Studio FCC Caution. §15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user.
user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This wireless phone meets the government's requirements for exposure to radio waves.