NDC2210S-iPHONE USER MANUAL 1
CONTENTS 1. INTRODUCTION ..........................................................................................5 1.1 OVERVIEW OF HARDWARE ..................................................................................................... 5 1.2 OVERVIEW OF SOFTWARE ...................................................................................................... 5 2. NDC2210S PHONE KEYBOARD ............................................................7 2.1 KEYBOARDS FUNCTIONS .....................
.5.7 Digital Map................................................................................................................ 25 3.5.8 Call Service Settings.............................................................................................. 26 3.5.9 Memory Key ............................................................................................................. 27 3.5.10 MMI Filter...........................................................................................................
Function 1. Provide a Backup SIP Server 2. Support NAT, Firewall 3. Support DHCP assigning IP address, etc automatically 4. Support PPPoE (used while connecting ADSL,cable modem) 5. It can update the program through HTTP ,FTP and TFTP 6. Check the dynamic voice; Soft the noise; Buffer technique of voice 7. Hold Function 8. Hotline Function 9. Speed-dial 10. Call-forward, Three-way conference call 11. DND (Do Not Disturb), Black List, Limit List 12. Auto-answer. 13. Set through standard Web Browser 14.
1. Introduction This is the user manual of NDC2210S. Some configuration should be done before use the NDC2210S phone, then it can work normally. This manual will illustrate how to set the phone through keyboard and web service. 1.1 Overview of Hardware 1.1.1 The two RJ-45 network interface support the 10/100M Ethernet. The default WAN interface is a DHCP Client server. User connect the WAN interface to ADSL or switch, and connect the LAN interface to the computer.
l Call Forward l Web Browser l Caller ID l Console/Telnet l 3-way conference l Keypad DTMF Firmware Upgrade l DTMF RELAY l TFTP l DTMF RFC 2833 l HTTP l DTMF SIP Info l FTP SIP Server Provide a Backup SIP Server 6 www.fineprint.
2. NDC2210S phone keyboard 2.1 Keyboards functions 2.1.
Flash 1 Off-Hook Dialing On-Hook Dialing 2 On-Hook Quickly cut off the current line and off-hook again.
register mode, then ON/OFF indicator light on the handset ,and will give the prompt tone for successful registration. 2.2.5 Delete handset Keep pressing the “FLASH” key on the base unit for three seconds, the Speaker will give “beep” sound, then Press “0” on the base unit to delete all the handset. Press “1” on the base unit to delete the first handset. Press “2” on the base unit to delete the second handset. Press “3” on the base unit to delete the third handset.
“ON/OFF” of the choice line. You can implement line switch. 2) Suppose the line1/2 of handset is holding, the line2/1 is dialing, if you want to switch to line1/2 talking, first hang up line2/1, then press down “ON/OFF” of Line1/2 or press “HOLD”. You can implement line switch. 2.2.8.2 Base unit Line Switch Suppose the line1/2 of the base unit is talking, line2/1 is holding, press down “line2/1” directly and switch to line2/1 talking. 2.3 Functions and setting catalog 2.3.
2) Private SIP 2.3.3.2 Limit-List 1) Current 2) ADD 3) DEL 2.3.3.3 Black-List 1) Current 2) ADD 3) DEL 2.3.3.4 FastCall 2.3.3.5 Three Talk 2.3.3.6 Call-Transfer 2.3.3.7 Call-Waiting 2.3.3.8 Call-Forward 1) Condition 2) SIP ◆Transfer Num ◆Transfer IP ◆Port 2.3.3.9 Dial-Rule 1) End With “#” 2) Fixed Length ◆Switch ◆Length 2.3.4 SIP 2.3.4.1 Reg Status 1) Public Reg 2) Private Reg 2.3.4.1 Reg Switch 1) Public 2) Private 2.3.4.2 Server 1) Public 2) Private 2.3.4.3 Domain 1) Public 2) Private 2.3.
2.3.4.9 RFC-version 2.3.4.10 Signal-Port 2.3.4.11 Stun 1) Switch 2) Addr 3) Port 4) Expire Time 2.3.5 DSP 2.3.5.1 Codec 2.3.5.2 Handdown-time 2.3.5.3 Dtfm-Volume 2.3.5.4 Input-Volume 2.3.5.5 Output-Volume 2.3.6 System 2.3.6.1 Save 2.3.6.2 Reboot 2.3.6.3 Set Default 2.3.7 Other Setting 2.3.7.1 Syslog 1) Switch 2) Server-IP 3) Server-Port 2.3.8 Setting catalog 1. Pressing down the “Menu” key to enter the setting status of speed dial key and input the needed saving No.
3. Through web browser to set phone Plug one end of the network line to the network card port of the computer, the other end to Lan port of the phone, phone will obtain the IP address automatically, open IE, input the IP address on Address column, then enter into the Web Setting Page. The method of obtaining the dynamic IP address is: under the on-hook status, press “**47#”, then phone will broadcast the current IP address. 3.1 Logon The default user name and password are admin/admin and guest/guest.
3.3 Network 3.3.1 Wan Config WAN port network setting page. Support static IP, dynamic obtain IP and PPPoE.
----Enable PPPoE ----PPPoE server: Enter “ANY” if no specified from your ITSP. ----Enter PPPoE username and password in the username and password. NDC2210S will automatically obtain WAN port network information from your ITSP if PPPoE setting and the setup are correct. Notice: If user accesses the IP phone through WAN port. He/She should use the new IP address to access the IP phone when the WAN port address was changed. 3.3.
Register Server Addr: Register address of public SIP server; Register Server Port: Register port of public SIP server,default port is 5060; Register Username: Username of your SIP account (Always the same as the phone number); Register Password: Password of your SIP account. Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the same IP for register server and proxy server, in this case you don’t need to configure the proxy server information.
Enable(No Subscribe):MWI is enabled, but phone will not send SUBSCRIBE, if the server sends NOTIFY message indicating new voicemail received, MWI LED will also blink to prompt. SIP1 Subscribe will still be used in config file: config option “0” means “Disable”, “1” means “Enable (Subscribe)”, “2” means “Enable (No Subscribe)”. Advanced SIP Setting Register Expire Time: Register Expire time, default is 60 seconds.
registration of certification , The server can directly reply confirmation message. Detect Interval Time:Set server detect interval time,if phone open SIP detect server function,it will detect server every time whether or not to respond. Signal Encode:Open signal encrypt; Rtp Encode: Open voice encrypt; Enable Via rport: Whether support the RFC3581 or not. Enable Via rport is used in inside network,and needs SIP server support. To maintain network equipment with net device outside of NAT connection.
IAX Server Addr: Register address of public IAX server; IAX Server Port: Register port of public IAX server,default port is 4569; Account Name: Username of your SIP account (Always the same as the phone number); Account Password: Password of your IAX account.
3.5 Advance 3.5.1 DHCP Server DHCP server manage page. User may trace and modify DHCP server information in this page. DHCP Lease Table:display the IP-MAC corresponding table that the server distributed. Lease Table Name: Lease table name. Start IP: Start IP of lease table. End IP: End IP of lease table. Network device connecting to the NDC2210S LAN port can dynamic obtain the IP in the range between start IP and end IP. Lease Time: DHCP server lease time. Netmask: Netmask of lease table.
3.5.2 NAT Advance NAT setting. Maximum 10 items for TCP and UDP port mapping. IPSec ALG: Enable/Disable IPSec ALG; FTP ALG: Enable/Disable FTP ALG; PPTP ALG: Enable/Disable PPTP ALG; Transfer Type: Transfer type using port mapping. Inside IP: LAN device IP for port mapping. Inside Port: LAN device port for port mapping. Outside Port: WAN port for port mapping. Click Add to add new port mapping item and Delete to delete current port mapping item. DMZ Config: 21 www.fineprint.
3.5.3 STUN This page is used to set the private sip server, stun server, and back up sip server information. STUN Server setting: SIP STUN is used to realize SIP penetrates through NAT, when the phone configures IP and port of STUN server (default is 3478) and select Enable SIP Stun, common SIP server can be used to realize the phone to penetrate through NAT.
port to enhance system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to reconnect. Telnet Port: configure telnet transfer port, default is 23. RTP Initial Port: RTP initial port. RTP Port Quantity: Maximum RTP port quantity, default is 200 Notice: Settings in this page won’t take effect unless save and reboot the device. If you need to change telnet port or HTTP port, please use the port greater than 1024, because ports under 1024 is system remain ports.
Input/Output: Specify current adding rule is input rule or output rule. Deny/Permit: Specify current adding rule is deny rule or permit rule. Protocol Type: Protocol using in this rule: TCP/IP/ICMP/UDP. Port Range: Port range of this rule. Src Addr: Source address. It can be a specific IP address or network address. Dest Addr: Destination address. It can be a specific IP address or network address. Src Mask: Source address mask. Indicate the source is dedicate IP if set to 255.255.255.255.
ult is 0xb8 ,oxb8 stands for best fast transmission; 28-38 is guarantee for the transmission priority for the 1st rank , 48-58 is guarantee for the transmission priority for the 2nd rank, 68-78 is guarantee for the transmission priority for the 3rd rank, 88-98 is guarantee for the transmission priority for the 4th rank. 802.1P Priority: The priority of 802.1p 3.5.7 Digital Map Digit map is a set of rules to determine when the user has finished dialing.
immediately. 955xx:5 digits numbers begin with 9 will be sent immediately. 10060:Number 10060 will be sent will be immediately 22xxxxxT1:7 digits numbers begin with 22 will be sent after one second 39[3,9]xxxx : 7 digits numbers begin with 393 or 399 will be sent immediately. 3.5.8 Call Service Settings User configure the value add service such as hotline, call forward, call transfer, call waiting, 3-way conference call, auto-answer, etc in this page。 Hotline: configure hotline number.
Enable Call Transfer: Please refer to Value_add_service for detail. Enable Call Waiting: Enable/disable Call Waiting Enable Three Way Call: Please refer to Value_add_service for detail. Accept Any Call: If this option is disable, NDC2210S refuse the incoming call when the called number is different from NDC2210S’s phone number. No Answer Time: no answer call forward time setting. Black List: incoming call in these phone numbers will be refused.
3.5.11 DSP This page mainly completes voice configuration. CODEC: select the prefer CODEC; support ulaw, alaw, G729 and G7231 5.3/6.3 Signal Standard: Signal standard for different area. Handdown Time: Hand down detect time. Input Volume: Handset in volume. Output Volume: Handset out volume. Handfree Volume: Hand free volume G729 Payload Length: G729 payload length VAD: Enable/disable Voice Activity Detection 3.5.
to the terminal. If there is a IP address shown on terminal (except for 0.0.0.
3.7 Config Manage Save Config: Save current settings. Clear Config: Restore to default settings. Backup Config: Backup the config file, via point the right key of mouse-à save target as….-àwill pop a save window, then type the config file name in the File name (the file type is text file) Update Configuration: Update the current configuration through configuration files.
3.8 Update Firmware 3.8.1 Update Web Update: Update the application or configuration files of the phone. The application document is .z format, and the configuration files is .cfg format. Through clicking on the "browse" button to open the upgrade file or configuration file, then click on "Update" button. After the upgrade, The phone will automatically restart. Notice:When upgrading, WEB page can not be closed.
3.8.2 Auto Update Current Version: the system will display the current version number Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file Config Encrypt Key: The encrypt key of confirmation file Protocol Type: The protocol type that used for upgrading Update Interval Time: The interval time that the terminals search for new configuration file.
3.9 System Manage 3.9.1 Account Manage Set web access account or keypad password of NDC2210S. 3.9.2 Syslog config Set the system log Server IP: set the syslog server address Server Port: set the syslog server port 33 www.fineprint.
MGR Log Level: set the MGR log level SIP Log Level: set the SIP log level IAX2 Log Level: set the IAX2 log level Please click “apply” after setting 3.9.3 Phone Book 3.9.4 Time Set This page layout is the setting of time of phone. Server: type the IP address of time server Timezone: select correct time zone in list box Timeout: longest response time for SNTP Daylight: daylight saving time SNTP: select SNTP server 12 Hours Format: select 12 hours format Manual Config: time setting 34 www.fineprint.
3.9.5 MMI SET Set the greeting information on LCD. 3.9.6 Logout & Reboot Logout:logout the Web entry. Reboot Phone:logout the entry, and reboot the phone. When user modifies any config of the phone, it will take effect after being rebooted, you can enter into this layout and click “Reboot”. And the phone will be rebooted automatically. Note:Reboot IP phone, some setting needs to reboot to make it works. Please always save config before reboot, otherwise the setting will return to previous setting.
www.fineprint.
4. Operating Method for Dialing 4.1 How to dial IP Phone Yon can make a call after being made a proper setting on your phone. Please confirm whether all the net wires are connected correctly. If you want to make a call, you can make it after dialing the number and then pressing “#”. You can find IP address through the menu. Modifying the IP address of the computer, and making it the same net as NDC2210S.
Register Server Port: Register port of public SIP server,default port is 5060 Register Username: Username of your SIP account (Always the same as the phone number) Register Password: Password of your SIP account. Phone Number: Phone number of your SIP account ----choose Enable Register; You can dial VoIP phone when the WAN interface and IAX protocol are being set correctly.
IAX Server Port: Register port of public IAX server,default port is 4569 Account Name: Username of your SIP account (Always the same as the phone number) Account Password: Local port: Password of your IAX account. Signal port of local, default port is 4569 Phone Number: Phone number of your IAX account ----choose Enable Register; ----if you use IAX account to make a call, please choose IAX(Deault Protocol), if you fail to choose it, then you can use SIP account to make a call again.
Suffix (optional): Configure suffix, show no suffix if not set Instance: 2T rule: If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to private SIP server. 3T rule: If the call starts with 3, the first 3 will be deleted, and the rest number with be sent to public SIP server. 123 rule: Dial 123 and will send 06332221015 to your server. It is used as speed dial function. 0T rule: If the call begins with 0, the first 0 will be replaced by 86.
MWI LED will blink to prompt; If “Enable (No Subscribe)” is selected, MWI is enabled, but Subscribe will not be sent, if the server sends NOTIFY message indicating new voicemail received, MWI LED will also blink to prompt. After the voicemails are picked-up, MWI LED will stop blinking. Compliance Statement FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.