9600IP PHONE USER MANUAL FOR MODEL: SIP 9600IP, SIP 9602IP Version：v1.
CONTENTS 1. INTRODUCTION....................................................................................5 1.1 OVERVIEW OF HARDWARE ......................................................................... 5 1.2 OVERVIEW OF SOFTWARE .......................................................................... 5 2. 9600IP PHONE KEYBOARD ...................................................................7 2.1 KEYBOARDS FUNCTIONS ............................................................................ 7 2.
.5.8 Call Service Settings.................................................................... 26 3.5.9 Memory Key ............................................................................... 27 3.5.10 MMI Filter................................................................................. 28 3.5.11 DSP ......................................................................................... 28 3.5.12 VPN ......................................................................................... 29 3.
Function 1. Provide a Backup SIP Server 2. Support NAT, Firewall 3. Support DHCP assigning IP address, etc automatically 4. Support PPPoE (used while connecting ADSL，cable modem) 5. It can update the program through HTTP, FTP and TFTP 6. Check the dynamic voice; Soft the noise; Buffer technique of voice 7. Hold Function 8. Hotline Function 9. Speed-dial 10. Call-forward, Three-way conference call 11. DND (Do Not Disturb), Black List, Limit List 12. Auto-answer. 13. Set through standard Web Browser 14.
1. Introduction This is the user manual of 9600IP. Some configuration should be done before use the 9600IP phone, and then it can work normally. This manual will illustrate how to set the phone through keyboard and web service. 1.1 Overview of Hardware 1.1.1 The two RJ-45 network interface support the 10/100M Ethernet. The default WAN interface is a DHCP Client server. User connect the WAN interface to ADSL or switch, and connect the LAN interface （the default IP address is 192.168.10.1) to the computer.
l Call Forward l Web Browser l Caller ID l Console/Telnet l 3-way conference l Keypad DTMF Firmware Upgrade l DTMF RELAY l TFTP l DTMF RFC 2833 l HTTP l DTMF SIP Info l FTP SIP Server Provide a Backup SIP Server 6
2. 9600IP phone keyboard 2.1 Keyboards functions 2.1.
Redial Dialing Volume + Call Increase the volume Redial the number of last time Volume - Call Reduce the volume Flash Off-Hook Quickly cut off the current line and off-hook again.
to hold the #1 handset then pick up the #2 handset. 2.2.4 Register handset Under On-Hook status, pressing the “Locate” key on the base unit for three seconds to enable the handset register mode, and the Charge indicator light flashes at the same time ;then press “*”key for three seconds to enable the handset register mode, then ON/OFF indicator light on the handset ,and will give the prompt tone for successful registration. 2.2.
make 3-way conference call. 2.2.8 Line Switch 2.2.8.1 Handset Line Switch 1）Suppose the line1/2 of handset is talking, the line2/1 is holding, if you want to implement line switch, first you need to press down “Hold ”, then press down “ON/OFF” of the choice line. You can implement line switch. 2) Suppose the line1/2 of handset is holding, the line2/1 is dialing, if you want to switch to line1/2 talking, first hang up line2/1, then press down “ON/OFF” of Line1/2 or press “HOLD”.
2.3.3 Call Feature 23.3.1 Phone-number 1) Public SIP 2) Private SIP 2.3.3.2 Limit-List 1) Current 2) ADD 3) DEL 2.3.3.3 Black-List 1) Current 2) ADD 3) DEL 2.3.3.4 Fast Call 2.3.3.5 Three Talk 2.3.3.6 Call-Transfer 2.3.3.7 Call-Waiting 2.3.3.8 Call-Forward 1) Condition 2) SIP ◆Transfer Num ◆Transfer IP ◆Port 2.3.3.9 Dial-Rule 1) End with “#” 2) Fixed Length ◆Switch ◆Length 2.3.4 SIP 2.3.4.1 Reg Status 1) Public Reg 2) Private Reg 2.3.4.1 Reg Switch 1) Public 2) Private 2.3.4.
2.3.4.6 Dtmf-mode 2.3.4.7 Interval-time 2.3.4.8 Swap-server 2.3.4.9 RFC-version 2.3.4.10 Signal-Port 2.3.4.11 Stun 1) Switch 2) Addr 3) Port 4) Expire Time 2.3.5 DSP 2.3.5.1 Codec 2.3.5.2 Handdown-time 2.3.5.3 Dtfm-Volume 2.3.5.4 Input-Volume 2.3.5.5 Output-Volume 2.3.6 System 2.3.6.1 Save 2.3.6.2 Reboot 2.3.6.3 Set Default 2.3.7 Other Setting 2.3.7.1 Syslog 1) Switch 2) Server-IP 3) Server-Port 2.3.8 Setting catalog 1.
3 Through web browser to set phone Plug one end of the network line to the network card port of the computer, the other end to Lan port of the phone, phone will obtain the IP address automatically, open IE, input the IP address on Address column, then enter into the Web Setting Page. The method of obtaining the dynamic IP address is: under the on-hook status, press “**47#”, then phone will broadcast the current IP address. 3.1 Logon The default user name and password are admin/admin and guest/guest.
Configure Static IP: ----Enable Static; ----Set 9600IP’s IP address in the IP Address; ----Set netmask in the Netmask field; ----Set router IP address in the Gateway; ----DNS Domain: ----Set local DNS server in the Preferred DNS and the Alternate DNS。 Configure to dynamic obtain IP ----Enable DHCP; If there is DHCP server in your local network, 9600IP will automatically obtain WAN port network information from your DHCP server.
----PPPoE server: Enter “ANY” if no specified from your ITSP. ----Enter PPPoE username and password in the username and password. 9600IP will automatically obtain WAN port network information from your ITSP if PPPoE setting and the setup are correct. Notice: If user accesses the IP phone through WAN port. He/She should use the new IP address to access the IP phone when the WAN port address was changed. 3.3.
Register Server Addr: Register address of public SIP server; Register Server Port: Register port of public SIP server，default port is 5060; Register Username: Username of your SIP account (Always the same as the phone number); Register Password: Password of your SIP account. Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the same IP for register server and proxy server, in this case you don’t need to configure the proxy server information.
Register Expire Time: Register expires time, default is 60 seconds. 9600IP will auto configure this expire time to the server recommended setting if it is different from the SIP server.
Signal Encode:Open signal encrypt; Rtp Encode: Open voice encrypt; Enable Via rport:Whether support the RFC3581 or not. Enable Via rport is used in inside network,and needs SIP server support. To maintain network equipment with net device outside of NAT connection. Enable Session Timer:Whether support the RFC4028 or not .At a certain period of time to refresh conversation ,in case a long time ,the other side drop off or break off,after refresh ,the other side did not respond ,we will hang up.
IAX Server Addr: Register address of public IAX server； IAX Server Port: Register port of public IAX server，default port is 4569； Account Name: Username of your SIP account (Always the same as the phone number)； Account Password: Password of your IAX account.
3.5 Advance 3.5.1 DHCP Server DHCP server manage page. User may trace and modify DHCP server information in this page. DHCP Lease Table：display the IP－MAC corresponding table that the server distributed. Lease Table Name: Lease table name. Start IP: Start IP of lease table. End IP: End IP of lease table. Network device connecting to the 9600IP LAN port can dynamic obtain the IP in the range between start IP and end IP. Lease Time: DHCP server lease time. Netmask: Netmask of lease table.
3.5.2 NAT Advance NAT setting. Maximum 10 items for TCP and UDP port mapping. DHCP Lease Table：Show IP—MAC corresponding table assigned by DHCP server. IPSec ALG: Enable/Disable IPSec ALG; FTP ALG: Enable/Disable FTP ALG; PPTP ALG: Enable/Disable PPTP ALG; Transfer Type: Transfer type using port mapping. Inside IP: LAN device IP for port mapping. Inside Port: LAN device port for port mapping. Outside Port: WAN port for port mapping.
3.5.3 STUN This page is used to set the private sip server, stun server, and back up sip server information. STUN Server setting: SIP STUN is used to realize SIP penetrates through NAT, when the phone configures IP and port of STUN server (default is 3478) and select Enable SIP Stun, common SIP server can be used to realize the phone to penetrate through NAT.
3.5.5 Firewall settings Firewall settings page. User may set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet (input rule), or prevent unauthorized private network devices to access the internet. Access list support two type limits: input_access limit or output_access limit. Each type supports 10 items maximum. 9600IP firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address.
3.5.6 VLAN Configuration 9600IP phone implement QoS based on 802.1p, The QoS is used to mark the network communication priority in the data link/MAC sub-layer. 9600IP will sort the packets using the QoS and sends it to the destination.
priority for the 2nd rank, 68-78 is guarantee for the transmission priority for the 3rd rank, 88-98 is guarantee for the transmission priority for the 4th rank. 802．IP Priority: The priority of 802.ip 3.5.7 Digital Map Digit map is a set of rules to determine when the user has finished dialing. 9600IP support below digital map: Digital Map is based on some rules to judge when user end their dialing and send the number to the server.
3.5.8 Call Service Settings User configure the value add service such as hotline, call forward, call transfer, call waiting, 3-way conference call, auto-answer, etc in this page Hotline: configure hotline number. 9600IP immediately dials this number after hook-off if it is set. Auto Answer: Enable/disable auto answer function. No Disturb: DND, do not disturb, enable this option to refuse any calls. Ban Outgoing: Enable this to ban outgoing calls.
3.5.9 Memory Key This page layout shows the number setting of Voice mail and speed-dial key.
to voice messages. 3.5.10 MMI Filter MMI filter is used to make access limit to 9600IP phone. When MMI filter is enable. Only IP address within the start IP and end IP can access 9600IP phone. 3.5.11 DSP CODEC: select the prefer CODEC; support ulaw, alaw, G729 and G7231 5.3/6.3 Signal Standard: Signal standard for different area. Handdown Time: hand down detects time. Input Volume: Handset in volume. Output Volume: Handset out volume.
3.5.12 VPN This page is VPN setting page, the IP phone support the VPN with UDP and L2TP protocol .The parameters is as below: VPN IP： After VPN registered successfully, VPN server will give an IP aggress to the terminal. If there is a IP address shown on terminal (except for 0.0.0.
3.7 Config Manage Save Config: save current settings. Clear Config: restore to default settings. Backup Config: Backup the config file, via point the right key of mouseà save target as…. àwill pop a save window, then type the config file name in the File name (the file type is text file) Update Configuration: Update the current configuration through configuration files.
3.8 Update Firmware 3.8.1 Update Web Update： Update the application or configuration files of the phone. The application document is .z format, and the configuration file is .cfg format. Through clicking on the "browse" button to open the upgrade file or configuration file, then click on "Update" button. After the upgrade, 9600IP will automatically restart. Notice: when the upgrades, WEB page cannot be closed.
3.8.2 Auto Update Current Version: the system will display the current version number Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file Config Encrypt Key: The encrypt key of confirmation file Protocol Type: The protocol type that used for upgrading Update Interval Time: The interval time that the terminals search for new configuration file.
3.9 System Manage 3.9.1 Account Manage Set web access account or keypad password of 9600IP. 3.9.
Please click “apply” after setting 3.9.3 Phone Book 3.9.4 Time Set This page layout is the setting of time of phone.
3.9.5 MMI SET Set the greeting information on LCD. 3.9.6 Logout & Reboot Logout：Exit the Web entry. Reboot Phone：Logout the entry, and reboot the phone. When user modifies any config of the phone, it will take effect after being rebooted, you can enter into this layout and click “Reboot”. And the phone will be rebooted automatically. Note：Reboot IP phone, some setting needs to reboot to make it works. Please always save config before reboot, otherwise the setting will return to previous setting.
4. Operating Method for Dialing 4.1 How to dial IP Phone You can make a call after being made a proper setting on your phone. Please confirm whether all the net wires are connected correctly. If you want to make a call, you can make it after dialing the number and then pressing “#”. You can find IP address by the menu. Modify the IP address of the computer, and making it the same net with 9600IP.
----choose static; ----fill in the IP address of 9600IP in the IP address; ----fill in the subnet mask in Netmask; ----fill in the router address or up Gateway address in the Gateway; ----fill in the local DNS server address in the Primary DNS and Alter DNS respectively. Configure to dynamic obtain IP to get IP address: ----choose DHCP option. Now, if the network has DHCP server, then 9600IP will get IP address, Netmask, Gateway, Primary DNS and Alter DNS from this DHCP server automatically.
4.2.2 SIP setting Enter into the VoIP à SIP Config to set the layout config and sip account information: Register Server Addr: Register address of public SIP server Register Server Port: Register port of public SIP server，default port is 5060 Register Username: Username of your SIP account (Always the same as the phone number) Register Password: Password of your SIP account.
4.2.3 IAX2 setting IAX Server Addr: Register address of public IAX server IAX Server Port: Register port of public IAX server，default port is 4569 Account Name: Username of your SIP account (Always the same as the phone number) Account Password: Password of your IAX account.
You can click “Add” to add a new dial rule. Below is the detail setting of the dial-rule: Phone Number: The Number suit for this dial rule can be set as full match or prefix match. Full match means that if the number user dialed is completely the same as this number, the call will use this dial-rule.
2T rule: If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to private SIP server. 3T rule: If the call starts with 3, the first 3 will be deleted, and the rest number with be sent to public SIP server. 123 rule: Dial 123 and will send 06332221015 to your server. Be used as speed dial function. 0T rule: If the call is begin with 0, the first 0 will be replaced by 86. Means that if you dial 06332221015，and 9600ip will send 866332221015 to your server.
FCC Warning： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Privacy of communications may not be ensured when using this telephone.
