Getting Started Guide
10
Wiring/Connecting
RMS Power Rating (rated at 0.1% THD)
Max Power
Power Supply
Power Supply
(Threshold)
Distortion
THD (1KHz @4Ω)
S/N Ratio
(A weighted @1W)
S/N Ratio
(A weighted @ FP)
Input Sensitivity
Hi/Low Input Level
Input Impedance
Low Input Level
Crossover (-12dB/Oct)
High-Pass
PRODUCT SPECIFICATIONS
Fuse Ratings
Power Supply
Frequency Response
Idle Current
ATC FUSE
Dimensions:
Lenght (inches/mm)
Height (inches/mm)
Bandwidth (+/-3dB)
Topology
Type
RMS Power (4 Ω)
Full PWM
10.0VDC -
17.0VDC
0.1%
-85dBA
-101.1dBA
0.15V - 12.0V
20 KΩ
4,500Hz
(0.7A)
20A
24”/627m
4.46”/ 113mm
70Hz-20KHz
Full Range Class D
RPMSB3X
400 W MAX
100 W
20 KΩ
30A
10Hz-20KHz
RPMSB4X
800 W MAX
Full PWM
10.0VDC -
17.0VDC
0.1%
--90dBA
-101.1dBA
0.15V - 12.0V
(0.7A)
Full Range Class D
200 W RMS
RPMSB4X
• 4” Six Speaker Waterproof Soundbar System
• 4” Speaker 10oz magnet
• 1” Titanium dome neodymium tweeter
• 1” Voice coil
• Santoprene PP cone
• 40W RMS power handling
• Frequency Response: 70-20Khz
• Sensitivity: 88dB+/-3dB
• THD < 10%
• Bluetooth and AUX
• 100 WRMS@4-ohm power output
• On/Off Switch
Driver Compliment
4 - 4” Mid Woofer
2 - 1”
Titanium dome neodymium tweeter
6 - 3” Mid Woofer
2 - 1”
Titanium dome neodymium tweeter
4,500Hz
Inputs
Bluetooth and AUX
Depth (inches/mm)
Over All Height (inches/mm)
4.1”/104.4m
6.96”/ 177mm
34”/866m
3.87”/ 198.5mm
3.8”/96.8m
6.46”/ 164.2mm
Bluetooth and AUX
1. If installing on an electric vehicle,switch it into TOW mode. Carefully remove the
Positive (+) then Negative (-) battery wires.
2. If installing on a gas vehicle,wire the Negative (Black) wire to the Negative (-)
battery terminal and the Positive (Red) wire to the Positive (+) battery terminal.
3. Route the thick Blue Aux In & Aux Out wires to your desired location. The Aux In
is for a music source that does not have Bluetooth capability. The Aux Out is to
connect to an optional amplifer or amplified subwoofer.
4. The Blue Remote Out wire provides +12V when the soundbar is powered on. This
may be used as a turn on (+12V) signal for additional amplifiers or an optional
amplified subwoofer.
5. Tie up all excess wires and reinstall the Positive (+) then Negative (-) battery wires.
If installing on an electric vehicle, switch it back into RUN mode.
Note: DC-DC Converter is required on electric vehicles to
avoid damage to the accessory and the vehicle
SOUNDBAR
18”/45cm
.250 FULLY INSULATED
SPADES ATTACHED AT
BOTH ENDS
18”/45cm
.250 FULLY INSULATED
SPADE ATTACHED
AT ONE END
SYSTEM TURN ON/OFF
(SP/ST CARLING SWITCH)
0.250” MALE
INSULATED SPADE
0.250” FEMALE
INSULATED SPADE
CERWIN VEGA MOBILE SOUNDBAR
0.250” FEMALE
INSULATED SPADE
AUX IN
AUX OUT( to amplied subwoofer or 2nd amplier)
TO BATTERY POSITIVE+
TO BATTERY NEGATIVE -