SmaRT 902 Remote Control System Manual U007.0-SmaRT902_system-R It2 ©2007 Cervis, Inc.
SmaRT Remote Control System This document is the property of Cervis, Inc. and cannot be copied, modified, or reproduced without the express prior written consent of Cervis, Inc. Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information without prior notification. FCC Statements 15.19 – Two Part Warning This device complies with Part 15 of the FCC rules.
User Manual Contents FCC Statements ............................................................................................................................ i 1.0 SmaRT 902 Remote Control System.................................................................................. 1 1.1 Features ............................................................................................................................. 1 1.2 PT0-902 Handheld Remote ...........................................................
SmaRT 902 Remote Control System Notes: ii U007.
Product Name 1.0 SmaRT 902 Remote Control System The standard SmaRT 902 Remote Control System consists of a 2-button PTO-902 wireless handheld transmitter, a BU-902F base unit, and the wiring harness that is used to connect the base unit to the controlled apparatus. A single base unit is capable of communicating with up to eight PTO-902 Handheld units.
SmaRT 902 Remote Control System 1.2 PT0-902 Handheld Remote The SmaRT PTO-902 Handheld Remote features a 300’ handheld-to-base unit communication range providing two function press-to-operate (PTO) control. Using direct sequence spread spectrum (DSSS) wireless technology at 900MHz, the handheld unit provides a robust link with a base unit in congested radio environments. SmaRT handheld units feature seamless association to a SmaRT BU-902F Base Unit without the need to open either case.
User Manual Figure 3. Female Twelve (12) Pin Connector The unit has five status/diagnostic LEDs that are used to determine the state of the unit. The LEDs are shown in Figure 4 below. Health OK – Green pulse/sec TX/RX – Yellow when transceiving POWER OK – Yellow Figure 4. BU-902F LEDs 1.
SmaRT 902 Remote Control System 5. When LINK flashes yellow, release the two buttons. The RX button flashes red allowing two (2) seconds for you to make the next button press. 9Note: If the next button press is not performed within the two second interval that RX flashes red, the procedure is aborted and must be started anew to establish the Association. 6. Press and hold the Associate button (See below). The RX extinguishes, the TX lights steady green, and the LINK LED lights steady yellow. 7.
User Manual 1. 2. 3. 4. Remove power from the base unit. Stand near the base unit in line of sight with the handheld in your hand. Press and hold both buttons (see Figure 5). TX lights steady green. Continue to hold both buttons for the five seconds it takes for the LINK LED to begin flashing yellow. 5. When LINK flashes yellow, release the two buttons. The RX button flashes red allowing two (2) seconds for you to make the next button press.
SmaRT 902 Remote Control System 2.0 Handheld Battery Installation or Change The SmaRT handheld unit is powered by three size AAA batteries. When installing batteries, be sure to observe proper polarity as marked on the inside of the compartment to avoid damaging the unit. 1. Remove the four small Phillips screws from the Battery Compartment cover and lift the cover from the handheld. 2. If installing batteries in an empty battery compartment, install three fresh size AAA batteries.
User Manual 3.0 Base Unit Installation CAUTION Make sure the machine on which the base unit is to be attached is disabled during installation. Use the configuration diagrams supplied by Cervis to guide you in mounting the base unit and connecting your wiring harness. Mounting of the base unit is left much to your discretion with the following guidelines: • • • • Before installing, make sure that the configuration diagrams supplied with the system are available.
SmaRT 902 Remote Control System 4.0 Using the SmaRT PTO-902 Handheld Remote The front panel of the SmaRT PTO-902 Handheld Remote has two (2) push-to-operate buttons and three (3) diagnostic LEDs. Each of the two buttons have dual functions as described in Figure 9.
User Manual 5.0 Wiring Harness ©2007 Cervis, Inc.
SmaRT 902 Remote Control System 6.0 Specifications 6.1 Handheld Table 1 - Handheld Specifications Item Description Power Vin +3.6V to +4.5V Batteries Auto-shutdown Three (3) AAA 5 Sec. of button inactivity TOperating -20°C to 55°C TStorage Humidity -40°C to 55°C (-40°F to 131°F) 0 to 100% Frequency 906-924MHz License No license required Modulation Antenna DSSS Internal Dimensions 119mm x 133mm x 36mm Environment (-4°F to 131°F) Radio Enclosure (5.24” x 4.69” x 1.
User Manual 6.2 Base Unit Table 2 - Base Unit Specifications Item Description Power Vin +9VDC to +16VDC Environment TOperating -20°C to 70°C (-4°F to 158°F) TStorage -40°C to 85°C (-40°F to 185°F) Humidity 0 to 100% Vibration/Shock IEC60068-2-6 Radio Enclosure Frequency 906-924MHz License Modulation Antenna No license required DSSS Internal Dimensions 119mm x 133mm x 36mm (5.24” x 4.69” x 1.
Cervis, Inc. Visit our Web site at: www.cervisinc.com The SmaRT Remote Control System is manufactured and distributed by Cervis, Inc. © 2007 Cervis, Inc. All rights reserved. Content is subject to change without notice. ©2007 Cervis, Inc. U007.