User's Manual

ManualsBrandsCeoTronics ManualsElectronicsWireless Control Command Transmitter

English - USA

Revision: 01/1014  DOK 1652-us

CT-WirelessPTT

Operation Instructions

For trouble-free operation of the receivers of the CT-WirelessPTT, make sure that

the receiver housing is not in the immediate vicinity of the transmitting antenna of

a radio or mobile phone. If the radio signal of the CT-WirelessPTT is overlaid by

the comparatively strong transmission signal of a radio or mobile phone, this can

impair the sensitivity of the CT-WirelessPTT in the near field of the transmitting

antenna. This can interrupt radio transmission from the PTT transmitter to the

PTT receiver!

A CT-WirelessPTT is a PTT (Push to Talk) button/transmitter for activation or control of special CeoTronics products which you

can covered keep in hand and use.

Possible CeoTronics products are for example:

CT-MultiPTT BT

CT-MultiPTT 2C MIL

CT-All-in-One Extreme

CT-BluetoothAdapter

CT-ClipCom Digital,- SD

CT-MultiCom Wireless PTT

In these products is a receiver for different CT-WirelessPTT installed. The CT-WirelessPTT must be paired with the receiver in

the CeoTronics products. The pairing, deleting and some functions of the CT-WirelessPTT can be different at the different

CeoTronics products. These procedures are described in the special user manuals of the CeoTronics products.

Operation Range: approximately 5 m Frequency: 916,5 MHz Modulation: FSK

CT-WirelessPTT MIL

4008007 / 916,5 MHz

CT-WirelessPTT Standard

4008004 / 916,5 MHz

Function by:

MIL

Standard

CT-MultiPTT BT – operation instructions Dok 1643

Bluetooth button

PTT

CT-MultiPTT 2C MIL – operation instructions Dok 1648

PTT – Primary radio circuit

PTT – Secundary radio circuit

ASR – change of level

CT-All-in-One Extrem – operation instructions Dok 1639

Modus 1/2

Modus 3/4

PTT

Volume -

NVK

Volume +

Volume -

NVK

CT-BluetoothAdapter – operation instructions Dok 1344

Bluetooth button

CT-ClipCom Digital SD – operation instructions Dok 1288

PTT

CT-MultiCom Wireless PTT – operation instructions Dok 1644

PTT

oder

Summary of content (4 pages)

PAGE 1
CT-WirelessPTT Operation Instructions For trouble-free operation of the receivers of the CT-WirelessPTT, make sure that the receiver housing is not in the immediate vicinity of the transmitting antenna of a radio or mobile phone. If the radio signal of the CT-WirelessPTT is overlaid by the comparatively strong transmission signal of a radio or mobile phone, this can impair the sensitivity of the CT-WirelessPTT in the near field of the transmitting antenna.
PAGE 2
Warning - and Safety instructions Notice for the use of the device for prevention of personal injury or property damage the national safety and accident prevention regulations and the following warning and safety instructions in this instruction manual.
PAGE 3
Receipt of goods Inspect the goods immediately upon receipt for completeness and possible transport damages! Notify transport damages immediately to the forwarder and CeoTronics AG! Transport and storage Make sure the environmental conditions specified in the technical data sheet are met and complied with in transit, at the storage location and site of operation! Take appropriate measures to avoid vibration, impacts and drops! Choose adecuate packaging when dispatching the device.
PAGE 4
Change of battery Type of battery: 3V CR2032 Art. No.: CR2032 Damage to the appliance! Pay attention to the correct polarity! Open the battery compartment with opening tool item no.: 4008011 by a swift left turn. Open cover – change the battery – mounting position circuit board touch-lamina remove the circuit board – Change the battery – minding mounting position sealing ring lid When closing put a new sealing ring under the lid, if necessary.