User's Manual

ManualsBrandsCentraLite Systems ManualsElectronicsZigbee Lamp Module

AZELA ZIGBEE HA Lamp Module

4256050-ZHA,ZHAC

Rated: 120 VAC, 60Hz

Rated 300W Incandescent @ 120V AC

Warnings and Cautions:

 To be installed and/or used in accordance with appropriate electrical codes and regulations.

 If you are unsure about any of these instructions, consult a qualified electrician.

 Unplug unit when servicing connected lamps.

 Save this instruction sheet. It contains important technical data along with testing

and troubleshooting information which will be useful after installation is complete.

INTRODUCTION

The CentraLite Azela ZIGBEE HA Lamp Module uses the

Zigbee Home Automation(HA) communication protocol to

link with other Zigbee HA devices. Each Lamp Module

acts as a router for messages sent through the Zigbee

network.

FEATURES

 Status LED

 Load control from button on Lamp Module

 Ease of installation

 Compatible with other Zigbee HA certified level

controllers

 ZHAC devices sense and report realtime load

current consumption

INSTALLATION

STEP 1

Attach the plug from the lamp to be con-

trolled into the receptacle of the Lamp

Module.

STEP 2

Attach Lamp Module to wall receptacle.

Verify that the receptacle is powered. If

the receptacle is powered by a wall

switch, the wall switch must be kept ON

at all times for the module to operate

properly.

STEP 3

To join the ZIGBEE HA Lamp Module to

a certified HA controller be sure that the

HA controller is open for joining. If the

Lamp Module has not been joined to a

network then press and hold the Lamp

Module button. The Lamp Module will

then attempt to join an open HA network.

Upon a successful joining of the Lamp

Module to a Zigbee HA network the

status LED will blink 2 times. When the

Lamp Module powers up after being

joined to a Zigbee HA network, it will

blink 2 times.

4256050-ZHA,ZHAC

STEP 3 cont’d

If the Lamp Module will not join a Zigbee

HA network then:

 Make sure the Lamp Module is

powered up

 Ensure the Lamp Module is within

RF range of a routing device

 Make sure the target Zigbee net-

work is open for joining

STEP 4

Once the Lamp Module is joined to the

Zigbee HA network, use the certified HA

controller to configure the Lamp Module.

STEP 5

If it becomes necessary to remove the

Lamp Module from a Zigbee HA network

then you must factory default the Lamp

Module. To factory default the Lamp

Module:

 Remove the Lamp Module from the wall

receptacle

 Press and hold the Lamp Module button

 Reinstall the Lamp Module into the wall

receptacle while holding the button

 After 2 seconds the status LED will turn

 Once the LED is ON let go of the button

 The Lamp Module will now be reset to

factory defaults and ready to join to a

Zigbee HA network.

www.centralite.com

Summary of content (2 pages)

PAGE 1
AZELA ZIGBEE HA Lamp Module 4256050-ZHA,ZHAC www.centralite.com 4256050-ZHA,ZHAC Rated: 120 VAC, 60Hz Rated 300W Incandescent @ 120V AC Warnings and Cautions:   To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any of these instructions, consult a qualified electrician. INTRODUCTION The CentraLite Azela ZIGBEE HA Lamp Module uses the Zigbee Home Automation(HA) communication protocol to link with other Zigbee HA devices.
PAGE 2
AZELA ZIGBEE HA Lamp Module 4256050-ZHA,ZHAC Rated: 120 VAC, 60Hz 4256050-ZHA,ZHAC Troubleshooting If the Lamp Module is not working properly, proceed with the following steps:  Make sure the device is being supplied with a 120V, 60 Hz AC source.  Check the load that is being controlled. Is the lamp fixture turned on?  Make sure the controlled load does not exceed 300 Watts.