User's Manual

ManualsBrandsCentraLite Systems ManualsElectronicsZigbee Appliance Module

AZELA ZIGBEE HA Appliance Module

4256050-RZHA,RZHAC

Rated: 120 VAC, 60Hz

Rated 8A General Purpose, 480W Incandescent

Warnings and Cautions:

 To be installed and/or used in accordance with appropriate electrical codes and regulations.

 If you are unsure about any of these instructions, consult a qualified electrician.

 Unplug unit when servicing connected appliances.

 Save this instruction sheet. It contains important technical data along with testing

and troubleshooting information which will be useful after installation is complete.

INTRODUCTION

The CentraLite Azela ZIGBEE HA Appliance Module

uses the Zigbee Home Automation(HA) communication

protocol to link with other Zigbee HA devices. Each

Appliance Module acts as a router for messages sent

through the Zigbee network.

FEATURES

 Status LED

 Load control from button on Appliance Module

 Ease of installation

 Compatible with other Zigbee HA certified level

controllers

 RZHAC devices sense and report realtime load

current consumption

INSTALLATION

STEP 1

Attach the plug from the appliance to be

controlled into the receptacle of the

Appliance Module.

STEP 2

Attach Appliance Module to wall recepta-

cle. Verify that the receptacle is

powered. If the receptacle is powered by

a wall switch, the wall switch must be

kept ON at all times for the module to

operate properly.

STEP 3

To join the ZIGBEE HA Appliance Mod-

ule to a certified HA controller be sure

that the HA controller is open for joining.

If the Appliance Module has not been

joined to a network then press and hold

the Appliance Module button. The Appli-

ance Module will then attempt to join an

open HA network.

Upon a successful joining of the Appli-

ance Module to a Zigbee HA network the

status LED will blink 2 times. When the

Appliance Module powers up after being

joined to a Zigbee HA network, it will

blink 2 times.

4256050-RZHA,RZHAC

STEP 3 cont’d

If the Appliance Module will not join a Zigbee

HA network then:

 Make sure the Appliance Module is pow-

ered up

 Ensure the Appliance Module is within

RF range of a routing device

 Make sure the target Zigbee network is

open for joining

STEP 4

Once the Appliance Module is joined to

the Zigbee HA network, use the certified

HA controller to configure the Appliance

Module.

STEP 5

If it becomes necessary to remove the

Appliance Module from a Zigbee HA

network then you must factory default the

Appliance Module. To factory default the

Appliance Module:

 Remove the Appliance Module from the

wall receptacle

 Press and hold the Appliance Module

button

 Reinstall the Appliance Module into the

wall receptacle while holding the button

 After 2 seconds the status LED will turn

 Once the LED is ON let go of the button

 The Appliance Module will now be reset

to factory defaults and ready to join to a

Zigbee HA network.

www.centralite.com

Summary of content (2 pages)

PAGE 1
AZELA ZIGBEE HA Appliance Module 4256050-RZHA,RZHAC www.centralite.com 4256050-RZHA,RZHAC Rated: 120 VAC, 60Hz Rated 8A General Purpose, 480W Incandescent Warnings and Cautions:   To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any of these instructions, consult a qualified electrician.
PAGE 2
AZELA ZIGBEE HA Appliance Module 4256050-RZHA,RZHAC Rated: 120 VAC, 60Hz Rated 8A General Purpose, 480W Incandescent 4256050-RZHA,RZHAC Troubleshooting If the Appliance Module is not working properly, proceed with the following steps:  Make sure the device is being supplied with a 120V, 60 Hz AC source.  Check the load that is being controlled. Is the appliance fixture turned on?  Make sure the controlled load does not exceed 8 AMPs.