30 I Cre Pim sre wt Contents 1. Transmiter Feature Diagram 2. Install Batteries 3. Basic Operating 4. Binding Transmitter 5. Lock/Unlock Key Button 6. Steering Adjustment = Steering Servo Reverse Setting » Steering End Point Adjustment u Steering Digital Trimming Adjustment = Dual Rate Steering Adjustment 7. Throttle Adjustment » Throttle Reverse Setting = Throttle End Point Adjustment » Throttle Digital Trimming Adjustment 8. Auxiliary Channel 3 = Reverse Setting » On/Off Switch setting 9.
0 I Cre Pim sre wt 1.
30 I Cre Pim sre wt 2. Install Batteries 1. Remove the battery cover from the transmitter 2. Install 4 AA alkaline dry cell batteries 3, Insert the 4 AA batteries recording to the polarity 4, Replace the battery cover: 1 3.Basic Operation Switch Off... Switch On.
30 I Cre Pim sre wt 4. Transmitter Binding 1. Each transmitter is assigned with a random unique ID number. In order to begin using the transmitter system you will have to bind the receiver to the transmitter. Follow the receiver binding instruction on page 10. 5. Lock/Unlock key button Lock key button Unlock Key button 1. Push the "D/R" switch key toward to right 1. Push the "D/R" switch key toward 2. While holding the D/R switch tonight, tum ~~ to left the transmitter power switch to On 2.
30 I Cre Pim Ezra mt = Steering End Point Adjustment Left Steering End Point Adjustment 1. Turn the steering wheel fully to left 2. Once the value reaches the limit, a long steady "beep" will sound Decrease value; Turn the steering wheel fully to left and press key button Increase value: Turn the steering wheel fully | to left and press key STRAPLESS button 3, Use this to performing steering angle adjustment / decrease or increase Right Steering End Point Adjustment 1 1.
30 I Cre Pim sre wt = Dual Rate Steering Adjustment Decrease: Push the "D/R" button key to left Increase: Push the "D/R” button key to right 1. Once the value reaches the limit, a long steady "beep" will sound 2. Steering dual-rate allows on-the fly travel adjustment to both sides (left and right) of the steering servo. Left Right 7. Throttle Adjustment = Throttle Reverse 1. Press and hold ST L/key button. 2. While holding ST L/button key turn the transmitter power switch to On 3.
30 I Cre Pim sre wt » Throttle End Point Adjustment Throttle (Accelerate) 1. Pull and hold the throttle trigger fully to the high-side 2. Once the value reaches the limit, a long steady "beep" will sound Decrease: While holding the throttle trigger, press TH Rev/key button Increase: While holding the throttle trigger, press TH Fwd/+ key button 3, Use the TH Rev/or TH Fwd/+ key buttons to adjust the throttle to desired throw 4, This can also be performing when the receiver power is off. Brake (Accelerate) 1.
30 I Cre Pim sre wt » Throttle Digital Trimming 1. Once the value reaches the limit, a long steady "beep" will sound 2. Two short "beep” sound indicate conformation Decrease: Press TH Rev/key button Increase: Press TH Fwd/+ key button i 3. When the vehicle is not moving, This function allows to adjust the throttle to neutral position. Ps 8. Auxiliary Channel 3 Adjustment = Reverse 1.Press and hold the "CH3" key button 2. While turn on the power switch 3.Two short "beep" sound for conformation 4.
30 I Cre Pim sre wt = Turn On or Off CH3 Switch 1. With two quick press the CH3 key button Turn-On: Two short beep sound Turn-Off; One short beep sound 2. This function allow to turn On/Off the CH3 key-button. 9.Factory Reset = Factory Default Setting 1. Press and hold the "TH Rev/-" key button 2. While holding the "TH Rev/-" key button turn the transmitter power switch to On 3. Two short beep for conformation 4, Now your transmitter has reset to the factory setting.
30 I Cre Pim sre wt 10. FUN . « FUN Mode 1. Enter the FUN mode, Tum the transmitter power switch to On, press and hold the FUN key button, two short "beep" sound for conformation 2. To Leave the FUN mode, press the FUN key button once, two short "beep! sound for conformation 3. To FUN mode locks all the key button and throttle except the steering wheel. 11. Receiver = Receiver Binding 1. Turn the transmitter power switch to On 2. Press and hold the "binding button" on the receiver 3.
230 BEE Pres Dis re mo 13. Certification 1.Doc Declaration Hereby, [GTI Model sport Co.Ltd.] declares that the radio equipment type [AMP] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet 2. FCC Statement This device complies with Part 15 of the FCC Rules.
230 Bt Eee bs re, EET Old electric appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. 14.
