User's Manual

ManualsBrandsCellink ManualsComputers & AccessoriesRF Wireless Keyboard

RF COMBO 1

BATTERY INSTALLATION

Mouse

1. As shown as fig.1 to fig.4, please hold the mouse and press the center part of the

two keys with one thumb. Meanwhile, with the other hand, pull the top cap backward

and open it.

2. Put two AAA alkaline batteries according to its direction. Then, put back the top cap

(as shown as fig.3) aiming at and along with the waist of the mouse.

Caution:

When battery power is low, the mouse pattern will show red color on the

right-down corner of window screen for warning.

Keyboard

Open the battery cap, which is on keyboard's reverse side, place 4 pieces AAA Alkaline

batteries,

and put the cap back.

Every time after having changed batteries, please reset up the mouse

according to the steps of " SETUP FOR USE".

HARDWARE INSTALLATION

1. Shut down the power of the computer. (Caution: Do not plug in or out USB or PS/2

connector port when the power of the computer is still on, otherwise will damage

the computer.)

2. Connect the green connector of the receiver (according to the type you

have bought) to the PS/2 connection port of the computer, or connect the white

connector to the USB connection port on the computer.

3. Turn on the computer.

SOFTWARE INSTALLATION (DRIVE PROGRAM)

1. Insert the CD / Driver into Drive -D (In case the CD-ROM is in D-drive).

2. Get into "execution" on window screen. Click twice on the file of

"setup exe" in D-drive of the CD to proceed setup, and follow the

steps indicated in the screen to complete the setup.

3. After the setup has been completed, the screen will restart automatically.

And, it will show a mouse pattern on the right-down corner of the screen.

Caution: When it is in PS/2 mode, this driver doesn't support "Low battery display".

SETUP FOR USE

1. MOUSE:

Aim the front point of the mouse at receiver.

PRESS FIRST THE BUTTON ON THE REVERSE SIDE OF MOUSE, THEN PRESS THE

CONNECTOR BUTTON ON THE RECEIVER. (NEVER DO THE CONTRARY WAY.)

The LED lights of the mouse and keyboard will light up. When mouse LED light goes

off ,

it means the setup of the mouse is completed.

2. KEYBOARD:

PRESS THE BUTTON ON THE REVERSE SIDE OF KEYBOARD. When the LED light

of keyboard goes off, it means the setup of the keyboard is completed as well. And

you may start to work with this RF Combo device.

3. The setup must be completed in one minute. If exceeded, please repeat the steps.

MOUSE BUTTON FUNCTION SETUP

Summary of content (4 pages)

PAGE 1
RF COMBO 1 BATTERY INSTALLATION Mouse 1. As shown as fig.1 to fig.4, please hold the mouse and press the center part of the two keys with one thumb. Meanwhile, with the other hand, pull the top cap backward and open it. 2. Put two AAA alkaline batteries according to its direction. Then, put back the top cap (as shown as fig.3) aiming at and along with the waist of the mouse. Caution: When battery power is low, the mouse pattern will show red color on the right-down corner of window screen for warning.
PAGE 2
1. Get into setup from the control desk or directly click into the mouse pattern shown in right-down corner of the screen. It shows the functions as following: . Button : setup for habit of using right or left hand, adjustment of the speed of continuously pressing twice the mouse buttons, adjustment of numbers of column for each rolling. . Mouse Marking: to set up the pattern or mouse marking. . Wheel : to set up the functions of hot key, zooming, and rolling of auto-turning. .
PAGE 3
program. Find the file USB RF MOUSE and click Add / Remove. - In the window Confirm File Deletion, click YES. - In the window RF MOUSE , click the OK. - Check if the driver is already removed. If yes, click OK. For any problem in using this device, please reach to the Customer Service Center through the e-mail on the website.
PAGE 4