Safety Guide
Start using
4. Go to the APN menu tab and paste
the ICCID in the empty field.
5. Type the APN in the APN field,
click Add and Restart modem(s).
6. The APN is now activated. For a
private SIM card and network, you
may be required to enter a username
and password in the APN menu tab.
1
2
3
B
Connect GO to a LTE source If the LTE 1 indicator (and LTE
2, if applicable) is illuminated, you are already connected to the
internet. If your SIM cards require special configuration:
1. Access the GO device UI.
2. In the Modems menu, enter the
SIM card’s pin code in the Pin
code field and click Unlock.
3. If the SIM card requires a special APN,
copy the ICCID number for the Modem.
About the device
Power on GO
To power on GO, press the power button to the left of the
SIM card slots, holding the button down for 5 seconds.
Connect your devices to GO
» To connect your personal laptop/computer to GO by Ethernet
cable, insert one end of the cable in the GO LAN port, and
the other end in the Ethernet port of your computer.
» To connect your personal laptop/computer or mobile phone to
GO by Wi-Fi, search on your computer for the Wi-Fi network
named CelerwayXXXXXX (where the Xs are digits/letters), and
log in to Wi-Fi with the password CelerwayXXXXXXtest (where
the Xs are the same digits/letters as in the network name).
To access the GO device user interface (UI), open a web browser
to http://192.168.5.1/basic, with the default user basic and password
celerway or new credentials provided to you by your IT administrator.
If you cannot access your device’s UI, your device may not have been
activated, and you must contact your IT administrator to activate it.
Connect GO to a Wi-Fi source If you want GO to use one or
more of the available Wi-Fi networks:
1. Access the GO device UI.
2. In the Wifi menu tab, click Scan
to see available networks.
3. Choose the network, click Select.
4. Enter the password for the
selected Wi-Fi network
and click Connect.
5. If GO successfully connects
to a Wi-FI network, it will apear in the list of available interfaces.
Mounting antennas
If you have a GO model with external antennas, mount
the antennas only when the device is powered off.
Keeping the device cool
GO is a powerful enterprise router equipped with a battery that must
be kept cool, especially under heavy use and in warm environments.
For cooling, GO has two fans that you must keep unobstructed during
operation. For more information about GO battery safety, see the
sections Normal battery usage and Observe battery safety guidelines.
Open from
this end
1. Be sure that GO is powered off.
2. Open the rubber protector covering
the SIM cards slots. When open,
the protector remains attached
to the device on the left side.
3. Insert the SIM card(s) in the SIM
card slots with the connectors
oriented to you, as illustrated.
Orient SIM
cards as shown
WARNING Celerway GO contains Lithium Ion batteries which are
potentially hazardous: make sure you and any user of Celerway GO
has read and understood the battery warnings and instructions.
Inserting SIM cards
GO uses micro-sized cellular data SIM cards that you
must install in the SIM card slots as illustrated below.
Along the length of GO are 6 LED
indicators that are illuminated when
GO is powered on, its software is
running properly, and the network
interfaces are on/connected.
Device powered ON
S/W running properly
SIM1 modem connected
SIM2 modem (for dual
modem models) connected
2.4GHz Wi-Fi radio on 5GHz Wi-Fi radio on
Connect to other
internet sources
Connect other
devices
Power button
If you press and quickly release the
power button, you can check the battery
level as indicated by the 4 LEDs under the
battery icon. The battery is fully charged when all 4 LEDs are illuminated.
Should you need to charge GO, use only the original charging
equipment from Celerway. Stop charging GO when its battery is
fully charged. For more information on charging GO safely, see
Normal battery usage and Observe battery safety guidelines.
Charge GO
Charge other
devices
Battery level
GO has two Ethernet ports: a
WAN port for connecting GO to
a local wired internet source, and
a LAN port for connecting your
laptop or other devices to GO.
3
A
3
C
Connect GO to a Wi-Fi source behind login portals
Repeat steps 1 and 2 from the section above, then:
3. For the selected network,
click Continue WiFi Login.
4. You will be redirected to
the login portal of the WiFi.
Click Continue to accept
the warning and proceed to
complete the portal login.
*This device must be activated before use. For detailed
instructions, please refer to the Activation Guide.