Century 2000 Low Profile Coffee Brewers
CENTURY 2000 COFFEE BREWERS Manual Pourover Group - 120V Dimensions (inches) VOLTS TOTAL AMPS KW MODEL WARMERS C-2001P 1 BOTTOM 120 1.6 C-2002P 1 TOP, 1 BOTTOM 120 C-2003P 2 TOP, 1 BOTTOM C-2003PR 2 BOTTOM, 1 RIGHT C-2003PL 2 BOTTOM, 1 LEFT W D H 15 8.00 17.35 17.25 1.7 15 8.00 17.25 19.00 120 1.8 15 8.00 17.25 19.00 120 1.8 15 16.00 17.25 17.25 120 1.8 15 16.00 17.25 17.25 Automatic with Backup Group - 120V C-2001 1 BOTTOM 120 1.6 15 8.00 17.25 17.
1 17 2 16 3 15 4 14 5 13 6 12 7 11 8 10 9 PARTS LIST 1 2 3 4 5 6 7 8 9 COVER, POUROVER SCREW, TRUSS HEAD SL #8x3/8 NYLON RECEPTACLE #8 LABEL, SWITCH PANEL READY LIGHT - GREEN POWER SWITCH - RED WARMER SWITCH, AMBER BREW BASKET - BLACK LEGS 3/4" ADJUSTABLE U588Q P489A M408A NF08A C072A L217A L580A V001A M042A -7- 10 11 12 13 14 15 16 17 TOWER COVER BODY WELDMENT ASSEMBLY HEATER SWITCH SPST TOGGLE SWITCH BRACKET TOP COVER W/SINGLE WARMER ASSY GROMMET, 5/8 I.D.
1 20 2 19 18 3 17 4 16 5 15 6 14 7 13 8 9 12 21 11 PARTS LIST ITEM DESCRIPTION 10 PART NO 1 TROUGH SUB-ASSY RP97Q 2 3 4 SPRAY TUBE ASSY WASHER WASHER, RED SILICON H297Q P155A M197A 5 6 7 8 9 10 11 SPRAY HEAD ADAPTER SPRAY HEAD BRACKET, COMPONENT TERMINAL BLOCK, 3 POSITION ELBOW 90° SILICON TUBE 1/2" ID, 14" LG PLUG K107A E004A RS45A B171A K525A M611A M488A 12 TANK BODY RK48Q -8- 14 15 16 17 18 19 20 HEATER, 120V 1500W HEATER, 220V 2400W HEATER, 240V 3500W HEX NUT 1/4-18 x 3/4 SILIC
16 15 17 18 19 24 25 14 26 27 28 13 29 12 20 21 22 11 23 30 3 10 9 31 8 7 6 5 4 2 1 34 33 32 16 15 PARTS LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DESCRIPTION TUBING 1/4" COLD WATER INLET TUBING 1/4", NEEDLE VALVE EXT. NEEDLE VALVE (80242) MT. BKT, WATER INLET VALVE HOSE NUT FITTING VALVE, WATER INLET (.75GPM) 120V VALVE, WATER INLET (.
5 6 7 8 9 10 11 4 23 22 3 2 12 13 CECILWARE 1 24 14 21 20 19 18 17 16 15 PARTS LIST ITEM DESCRIPTION PART NO 1 2 3 4 5 6 7 8 9 10 11 SPRAY TUBE ASSEMBLY TIMER HOT WATER DISPENSER THERMOSTAT THERMOSTAT KNOB WATER LEVEL CONTROL WATER LEVEL SENSOR SILICONE GASKET SCREW 1/4-20 x 5/8 S.S.
WARNING: MACHINE WARRANTY IS VOID IF MACHINE IS CONNECTED TO ANY VOLTAGE OTHER THAN 120 VOLTS. (EXPORT UNITS SHOULD BE CONNECTED TO 220 VOLTS) ** INSTALLATION INSTRUCTIONS ** NOTE: A SEPARATE CIRCUIT SHOULD BE SUPPLIED FOR EACH OF THESE BREWERS WITH A 15 AMP CIRCUIT BREAKER OR FUSE. CHECK LOCAL CODES FOR COMPLIANCE IN INSTALLATION.
MANUAL POUROVER UNITS THESE INSTRUCTIONS ARE FOR INITIAL PRIMING ONLY AND DO NOT HAVE TO BE REPEATED FOR NORMAL OPERATION. 1. Remove sample filter pack from brew funnel and insert brew funnel back into machine. 2. Place an empty decanter on warmer plate directly under brew funnel. 3. Lift pourover cover and pour 4 decanters of cold water through the top opening at 3 minute intervals. After the third decanter is poured, water will flow through spray head and funnel and fill decanter beneath. 4.
1. Wash brew funnel and decanter by hand as needed. Do not use dishwasher, which may cause decanter breakage. 2. For cleaning all metal surfaces, use any reputable stainless steel cleaning compound. Spray head should be checked and cleaned regularly. (At least once a week.) Spray head holes must be kept open. To prevent “LIMING” problems in the water tube, remove spray head and insert spring probe all the way into the tank through the tube.
CAUTION: DISCONNECT POWER BEFORE ATTEMPTING ANY ELECTRICAL REPAIRS THERMOSTAT ADJUSTMENTS: NOTE: The thermostat is behind the lower front panel. If water temperature is less than 197 degrees F (92 degrees C) slowly turn thermostat knob clockwise until ready light goes out. When temperature of water approaches 197 degrees to 203 degrees F (92 degrees to 95 degrees C) slowly turn thermostat knob counterclockwise until the green ready light comes on.