LIPTON TEA BREWING EQUIPMENT Iced Tea Dispensers Hot Tea Dispensers MANUAL • SPECIFICATIONS • INSTALLATION MACHINE MODELS LTB-303 or PORTABLE LTB-505 or PORTABLE LTB-103 or PORTABLE LTB-105 or PORTABLE LTB-1010 LTB-1010 TWIN • OPERATIONAL INSTRUCTIONS • ADJUSTMENTS • COMPONENTS ICED TEA DISPENSERS LB1-3 gal. LB1-5 gal. LRB-3 gal. LRB-5 gal. SU-10P [10 gal.] HOT TEA DISPENSER 3 Lt. AIRPOT V226A • PARTS IDENTIFICATION • WIRING DIAGRAMS PLASTIC TRAYS and S.S.
LTB MODELS: LTB-303 W/ LIT STEEPING FUNNEL [HOT WATER SPOUT - OPTIONAL] LTB-1010 TWIN WITH PLATFORM FUNNEL LTB-505. W/ LIT STEEPING FUNNEL LTB-1010 W/PLATFORM FUNNEL LTB-103 . W/ PLATFORM FUNNEL LTB-105 .
ELECTRICAL SPECIFICATIONS MODEL NO. LTB-303C, 505-IT, LTB-103, 105 * LTB-PORTABLE - OPTIONAL LTB-303, 505, LTB-103, 105 LTB-1010, LTB-1010 DUAL VOLTS PHASE HZ WATTS NO. OF AMPS RECEPTACLE POWER KW HEATERS NEMA NO. CORD 120 1 60 1.8 1 15 5-15R 5-15P [2 WIRES+GND] 240 240 1 1 60 60 3.0 4.8 1 2 12.
FAST START UP INSTRUCTIONS FOR LTB-303, 505, 103, 105 CAUTION: BEFORE PLUGGING POWER CORD INTO GROUNDED OUTLET [15A, 120V 0r 240V] MAKE SURE HEATER SWITCH IS OFF [Heater Switch is located inside Top Housing. Remove Top Cover for Access]. I. PRIMING - FIRST TIME START UP - CONNECTED TO DIRECT WATERLINE 1. 2. 3. 4. 5. CONNECT A 1/4 Inch COPPER WATER LINE TO THE 1/4 FLARE WATER INLET FITTING ON THE VALVE. PLUG POWER CORD INTO DEDICATED OUTLET [120V, 15A, GROUNDED.] PRESS POWER SWITCH ON.
FAST START UP INSTRUCTIONS FOR LTB PORTABLE (Lipton Portable Tea Brewer with Pump) CAUTION: BEFORE PLUGGING POWER CORD INTO GROUNDED OUTLET [15A, 120V 0r 240V] MAKE SURE HEATER SWITCH IS OFF [inside top cabin]. I PRIMING - FIRST TIME START UP USING PUMP 1. 2. 3. 4. 5. SET WATER SELECTION SWITCH [see lower back panel] TO "PUMP" [TOGGLE UP] PLACE HOSE FROM PUMP [on back panel] INTO A 6 GAL. FULL WATER BOTTLE. PLUG POWER CORD INTO OUTLET [120V, 15A, GROUNDED, DEDICATED]. PRESS POWER SWITCH ON.
FAST START UP PROCEDURE FOR LTB -1010 & LTB-1010 TWIN CAUTION: BEFORE PLUGGING POWER CORD INTO GROUNDED OUTLET [15A, 120V 0r 240V] MAKE SURE HEATER SWITCH IS OFF [on back panel or inside top cabin]. I. PRIMING - FIRST TIME START UP CONNECTED TO DIRECT WATERLINE 1. 2. 3. 4. CONNECT A 1/4 COPPER WATER LINE TO THE 1/4 FLARE WATER INLET FITTING ON THE VALVE. PLUG POWER CORD INTO OUTLET [120V, 15A, GROUNDED, DEDICATED]. PRESS POWER SWITCH ON. Tank will start filling. WAIT APPROXIMATELY 4 MIN.
LTB-303 DIMENSIONAL SPECIFICATIONS ICED TEA BREW SW. HOT TEA BREW SW. LABEL HEATER LT. POWER SWITCH READY LT. FUNNEL BREW BASKET END CAP/NUT SIPHONING TUBE COLD WATER NOZZLE POWER CORD WATER INLET VALVE-HAND TIGHTEN LEGS LTB-103 DIMENSIONAL SPECIFICATIONS LABEL POWER SWITCH ICED TEA BREW SW. WITH READY LT.
LTB-505 DIMENSIONAL SPECIFICATIONS LABEL ICED TEA BREW SW. POWER SWITCH HEATER LT READY LT FUNNEL BREW BASKET BREW PLATFORM END CAP/NUT SIPHONING TUBE POWER CORD COLD WATER NOZZLE WATER INLET VALVE-HAND TIGHTEN LEGS BACK VIEW FRONT VIEW SIDE VIEW LTB-105 DIMENSIONAL SPECIFICATIONS LABEL POWER SWITCH ICED TEA BREW SW. WITH READY LT.
LTB-1010 DIMENSIONAL SPECIFICATIONS BACK VIEW FRONT VIEW SIDE VIEW ICED TEA BREW SW. WITH READY LT 10 gal. ICED TEA DISPENSER LTB-1010 TWIN DIMENSIONAL SPECIFICATIONS ICED TEA BREW SW. WITH READY LT 10 gal. 10 gal. ICED TEA DISPENSER ICED TEA DISPENSER 9 9 10 gal.
ACCESSORIES - DIMENSIONAL SPECIFICATIONS LB1-3 LB1-5 HTT3 HTT2 HTT1 LRB-1-3 LRB1-5 3 LITER AIRPOT 10
TEA BREWING RECOMMENDED MEASUREMENTS MODEL # LTB-303, LTB-103 LTB 505, LTB-105 LTB-1010 LTB-303 LTB-505 GROUND TEA LOOSE or BAGGED 2.5 - 3 oz. (1) 3 oz. bag 3.5 - 4 oz. (1) 4 oz. bag 8 oz. (2) 4 oz. bag Allow approximately 10 minutes for a complete brew cycle. DO NOT remove brew funnel until it has stopped dripping. Serve Fresh Brewed Tea from dispensing faucet into tea glass over ice. TEA BAGS - Place correct number of tea bag(s) directly into brew funnel.
SANITIZING AND CLEANING INSTRUCTIONS FOR LIPTON TEA BREWING EQUIPMENT - Wipe clean all surfaces of the machine. I. DAILY CLEANING OF MACHINE II. DAILY CLEANING OF FUNNELS 1. Clean and rinse brew funnel between brewing cycles. Wash steeping brew funnel weekly with soap and warm water, rinse thoroughly with fresh water. Remove brew basket from steeping funnel by spinning it off (ccw) or pull out platform from platform funnel. Use small/valve brush to clean brew funnel valve.
ADJUSTMENTS - TO BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONLY. Caution: Brewers should be unplugged from electrical outlets before any service is performed. The water flow rate coming from the hot water tank is constant/fixed at 0.75 gal/min. Increasing or decreasing the amount of hot water dispensed from tank can also be used to adjust the strength of the tea. The Longer water flows - More water - Weaker tea; Less water flows - Less water - Stronger tea.
4. PROGRAMMABLE TIMER "TEACH ME" L576A ADJUSTMENTS - LTB-1010 : This timer can be programmed from the brew button to dispense different volume of hot water. PRIMING: a. Make sure heater switch is off . b. Push & hold down brew button while switching power on . c. Release brew button. d. Push brew button again & wait for water to start flowing out of spray head. e. Switch power off . Put timer into program mode: a. Start with power off. b. While holding down brew button, turn power on. c.
CRITICAL COMPONENTS TESTS A) Water Inlet Valve Test Check hot water side, going to tank: Turn power off. If the water level rises inside the tank, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the terminals. Plug it into electrical outlet. If water flows in and stops when you pull it out, the Valve is working fine. Repeat this test a few times. The problem may be in the Probe or Water Level Control Board.
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the PROBLEM PROBABLE CAUSE 1 Brewed Cold Tea. a) Heater Switch OFF. b) Run out of hot water c) Thermostat is OFF. d) Loose electrical connection. e) Thermostat is defective. f) Hi-Limit Temperature Switch is tripped. 2 Tea too weak. a) Not enough Tea in the funnel insert. b) Water flow too low. c) Brew time is too short. d) Water is too cold.
FUNNEL ASSEMBLIES P/N DESCRIPTION M494A SEAL PLUG GROMMET RX60A TEA BAG SHELF K612A SIPHONING TUBE-DRIP FREE V239A BREW FUNNEL, CLEAR POLYCARBONATE 5 N816A CAUTION LABEL 6 4100A "O" RING 7 P499A LOCK NUT 1 2 3 4 P/N DESCRIPTION F412-LS PAPER FILTER W/HOLE- OPTIONAL M615A BREW BACKET- MOLDED H326Q SYPHONING TUBE S.S.
1 48 2 47 3 46 4 5 6 7 45 44 8 9 10 43 11 8 42 12 41 40 13 39 14 38 15 16 37 36 17 35 18 19 20 21 22 34 23 33 24 32 31 25 26 27 28 29 19 30
ITEM P/N LTB-303 LTB-505 P/N LTB-303 Portable 1 2 L566A L539A L566A L539A L566A L539A L566A L539A WATER LEVEL CONTROL SENSOR (CCA) RELAY, DOUBLE POLE (120V) [LOW TEMP.
1 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 S.S. BREW COVER SUPPLIED W/ MACHINE 2 3 4 BLACK S.S. COVER W/ TWIST LATCH ASS'Y 13 14 15 16 17 18 SE39Q 5 BLACK MOLDED COVER 6 LB1-3.3 AND LB1-5 COMPONENTS DESCRIPTION SS BREW COVER [SHIPPED W/ MACHINE] COVER, S.S., BLACK (COVER & LATCH ASS'Y SE39Q & SE40Q) BLACK KNOB SCREW, PAN HD 10-24 SS MOLDED COVER - BLACK TANK 3.3 GAL / 5 GAL [3 GAL. Q172A] HANDLES - BLACK HANDLE SCREW 8-32 x 1/2 NUT BLACK WASHER, RUBBER SHANK ASS'Y, W/PLASTIC WING NUT S.S.
LB-3.3 gal. LB-5 gal. Q184Q Q190Q MO28A MO28A P264A P264A Q080A R021A Q181A Q182A M632A M632A P015A P015A K105A K105A M080A M080A D025S D025S DO64A D064A DO84A D084A RZ86A SA32A NH63A NH63A LB1-3 AND LB1-5 COMPONENTS DESCRIPTION SS BREW COVER [SHIPPED W/ MACHINE] KNOB SCREW, PAN HD 10-24 SS COVER - BLACK TANK 3.3 GAL / 5 GAL [Q172A 3 GAL.] HANDLES - BLACK HANDLE SCREW 8-32 x 1/2 NUT BLACK WASHER, RUBBER SHANK ASS'Y, W/PLASTIC WING NUT - MODIFIED S.S.
ITEM 1 2 3 4 5 6 P/N M027A Q021A P546A SE39A M768A P049A ITEM 1 2 3 4 5 6 7 DESCRIPTION FOR LB1-5 gal. KNOB COVER - BLACK TWIST LATCH PLATE, S.S. F/ GASKET GASKET, BUT SPLICED HEX BOLT 3/8-16x7/8 1 1 P/N V226A M618A RV31A M633A RV30A M634A RV29A DESCRIPTION AIRPOT - 3 Liters [3/4 Gal.] MOLDED TRAY - TRIPPLE GRILL S.S. - TRIPPLE MOLDED TRAY - DOUBLE GRILL S.S. - DOUBLE MOLDED TRAY - SINGLE GRILL S.S.
CECILWARE CORPORATION
NOTE: THIS CIRCUIT IS FOR EXPORT MODEL ONLY.
CECILWARE CORPORATION
CECILWARE CORPORATION
