Network Interface Card User Guide Preliminary Revision Mar 2008 Network Interface Card User Guide TLG08UB05 CEC Huada Electronic Design Co., Ltd CEC Huada Electronic Design Co.
Network Interface Card User Guide Preliminary Revision Mar 2008 Statement AirLink® is a registered trademark of CEC Huada Electronic Design Co., Ltd (hereinafter referred to as HED) in China. Copyright © 2008 HED. All rights reserved. No part of this production, fittings or softwares, may be reproduced in any form without the prior written permission of HED. The content in this manual is for reference only. Information is subject to change without notice. Our home page is http://www.hed.com.
Network Interface Card User Guide Preliminary Revision Mar 2008 Table of Contents 1 Introduction.......................................................................................................................................... 4 1.1 Brief Introduction...................................................................................................................... 4 1.2 Product Features...............................................................................................................
1 Introduction 1.1 Brief Introduction TLG08UB05 wireless adapters is developed based on the CMOS chip HED05W01SU with the independence sciential property rights of HED .Using the wireless adapters, mobile office can be achieved for users without networks interrupted, and the networks can also be configured or extended without setup or move the cables by administrators.This kind of wireless adapters roundly support GB15926.
1.3 Indicator light Indication There is a link light on theTLG08UB05 wireless adapter , It’s used to indicate the state of data transmission, The detail meanings of the status are as shown in the following table.
The wireless adapters support hot-plugging,but don’t pull out the wireless adpter in order to no data missing,when data is transmitting。 2.
(3) Pop-up GUI as follows,please select”Don’t search,I will choose the driver to install” ,and click button.。 Picture 2-2 Found New Hardware Wizard 2 (4) Pop-up GUI as follows,please click “Have Disk…”button,and pop-up Install From Disk dialog box。 CEC Huada Electronic Design Co.
Picture 2-3 Found New Hardware Wizard 3 (5)Select path from CD-ROM in pop-up dialog box as follows,then click OK。 CEC Huada Electronic Design Co.
Picture 2-4 Found New Hardware Wizard 4 (6) Click button in pop-up dialog box, ,and begin to copy file, wait for the file copying completely as follows。 CEC Huada Electronic Design Co.
Picture 2-5 Found New Hardware Wizard 5 (7) Click button, and driver installation is finished.。 CEC Huada Electronic Design Co.
Picture 2-6 The end of Found New Hardware Wizard Acount： Please click Continue Anyway button when windows system hint “has not passedWindows Logo testing to verify its compatibility with Windows Xp”。 (8) Begin to install configuration software, seach the file that named “AirQuick Utility V1.0.0.msi” ,and double click the file to beagin to install the file.。 CEC Huada Electronic Design Co.
Picture2-7 Configuraion software installation 1 (9) Click button,pop-up the next page,select installation path,and then click next until the page is as follows, click Finish to finish installation. From now you can use wireless adapter. CEC Huada Electronic Design Co.
Picture 2-8 Configuraion software installation 2 3 Configure wireless adapter Users can configure wireless adapter in computer with HED wireless network configuration software after installation finished.Users also can use wireless network configuration tool in Windows XP operation system.Advise using incidental HED wireless network configuration software。 3.
Picture3-1 Windows XP Configuration Tool 3.2 HED Wireless Network Configuration Tool Please insure that the configuration tool on use is HED Wireless Network Configuration Tool before the HED Wireless Config Tool is used. 3.2.1 Wireless Network Run HED Wireless Network Config Tool ,then pop-up GUI as Picture 3-2 CEC Huada Electronic Design Co.
Picture3-2 Wireless Network Configuration Tool 1.
Select a AP in list ,then click , can connect successfully with the AP。 STA Create Adhoc Network Disconnet the connected network Save current configuration as a file Click ,Pop-up Advance Setting Page,User can set many network parameter in this page. 3.2.2 Connection Status Select the AP and then Double click it toconnect with AP ,and pop-up the status page.
Table3-2 Connection Status Field Meanings Link Status Display current link status Network Name Display current network name Authenticate Type Display current network Authenticate Type Encryption Mode Display current network Encryption Mode TX Rate Display current network TX and RX max Rate, Unit is Mbps Channel Display current linked channel Signal Display current linked network signal that through RF receive signal,also can display in dBm fomat.
3.2.3 Advance Setting Click ,pop-up Advance Setting page as follows: Picture3-4 Advance Setting Every field in Advance Setting page means in the Table 3-3 as follows. Advise to apply Windows default。 Table 3-3 Advance Setting Field Work Mode Meanings Set wireless network communication protocol,include two mode:802.11b,802.
3.3 Use Wireless Network Configuration Tool of Windows XP own Acount：： Please ignore the chapter if the current operating system is not Windows XP If users want to use Windows XP Wireless Network Connection , Please choose Windows zero configuration menu and the means has been tell off in Chapter 3.1.
(2) Select AP which you want to connet ,and click . Picture3-16 Wireless Network Property Configuration CEC Huada Electronic Design Co.
