TL0901GU Network Interface Card User Guide （Windows XP version） ） CEC Huada Electronic Design Co., Ltd Http://www.hed.com.
Wireless Network Adapter User Guide for XP Preliminary Apr 2009 Statement AirLink® is a registered trademark of CEC Huada Electronic Design Co., Ltd (here in after referred to as HED) in China. All rights reserved. No part of this production, fitting or software, may be reproduced in any form without the prior written permission of HED. The content in this manual is for reference only. Information is subject to change without notice. Our home page is http://www.hed.com.cn. CEC Huada Electronic Design Co.
Wireless Network Adapter User Guide for XP Preliminary Apr 2009 Table of Contents Statement...........................................................................................................................................2 Product List .......................................................................................................................................4 1 Product Introduction ..........................................................................................................
Product List One Network Interface Card of MiniCard Interface One User Guide One Guarantee Card of Repair One CD contained Driver and Configure Software 1 Product Introduction 1.1 Brief Introduction USB wireless adapters is the product which is developed based on the WLAN network interface controller chip HED08W04SUA. Using the radio frequency (RF) technology, HED08W04SUA sends and receives data via the radio waves.
The adapter offer management software. Users can manage their adapters easily though this software without specialty knowledge. 1.4 Production Appearance Figure 1-1 Wireless USB Adapter Appearance 2 Installation 2.1 System Requirements (1) Windows XP operating system (2) A computer or laptop with an available USB port 2.2 Adapter Installation Please plug the wireless network adapter into the USB port directly.
The window of installation has a little difference in the different computer. The steps for setting up wireless network adapter: (1) Please insert HED wireless network adapter. (2) After computer detecting the adapter automatically, the Found New Hardware Wizard window will appear, as shown in figure2-1. Figure 2-1 Hardware Wizard 1 (3)Select Install from a list or specific location (Advanced), the window will appear as shown in figure 2-2 after click Next. CEC Huada Electronic Design Co.
Figure2-2 Hardware Wizard 2 (4) Select Don’t search, I will choose the driver to install, the window will appear as shown in figure 2-3 after click Next. Figure 2-3 Hardware Wizard 3 (5) The setup wizard will ask you to choose a Hardware Type. Select network adapters CEC Huada Electronic Design Co.
in the list, click Next to continue. The window will appear as shown in figure 2-4. Figure 2-4 Hardware Wizard 4 (6) Click Have Disk, select the path of installation from Browse in the Install From Disk window which is shown in figure2-5. Figure 2-5 Hardware Wizard 5 (7) Click OK, the window will appear as shown in figure 2-6.The setup wizard will ask you to choose a network adapter. Select HED08W04SUA Device, click Next to start copying files. CEC Huada Electronic Design Co.
Figure 2-6 Hardware Wizard 6 (8)After copying files, finish window will appear as shown in figure 2-7.Click Finish button to complete installation. CEC Huada Electronic Design Co.
Figure 2-7 Finish the Installation Notice: In the process of driver installation, click Continue Anyway when a clue on the Microsoft DTM appearing. 2.3.2 AirQuick Wireless Network Config Tool Installation The steps for setting up AirQuick Wireless Network Config Tool: (1) Click AirQuick Utility V2.0.6.msi, the InstallShield Wizard window will appear (As shown in figure 2-8). CEC Huada Electronic Design Co.
Figure 2-8 InstallShield Wizard 1 (2)Click Next to continue the installation, or click Cancel to end the installation. Figure 2-9 InstallShield Wizard 2 (3) Click Next to the window as shown in figure 2-9. Choose the destination folder. By default setup will install to the default location. To install to a different location, click change and specify the location. CEC Huada Electronic Design Co.
Figure 2-10 InstallShield Wizard 3 (4) After choose the folder, click Next on the Ready to Install the Program. As shown in figure 2-10, click Install to begin the installation. InstallShield Wizard finish window as shown in figure 2-11. Click Finish button to complete installation. Figure 2-11 InstallShield Wizard 4 CEC Huada Electronic Design Co.
2.4 Uninstall To remove the AirQuick Wireless Network Config Tool: Click Start →All Programs → HED→Airquick Utility v2.0.6 For WinXP English Version → Uninstall Airquick Utility v 2.0.
Figure 3-1 Network Manage Table 3-1 Meanings of the Network Manage Field Field Meanings SSID Displays the name of the wireless network. Channel Displays the channel of the wireless network. Signal Displays the signal of the wireless network. Authenticate Type Displays the authentication method of the wireless network, it contains open、open/presharekey、WPA-personal、WPA2-personal and so on. BSSID Displays the MAC address of the wireless device. Network Mode Includes of Ad hoc and Infrastructure.
< Advance > Configures the parameter of the network. 3.2.2 Link Information Link Info window is shown in figure 3-2. The meaning of the field is shown in table 3-2. Figure 3-2 Link Info Table 3-2 Meanings of the Link Info Field Field Meanings Link Status Displays the status of the wireless network connection. SSID Displays the name of the wireless network. Network Mode Includes of Ad hoc and Infrastructure. Authenticate Type Displays the authentication method of the wireless network.
MAC Address Displays the MAC address of the wireless device. 3.2.3 Advance Setting Advance Setting window is shown in figure 3-3.The meaning of the field is shown in table 3-3. Figure 3-3 Advance Setting Table 3-3 Meanings of the Advance Setting Field Field Meanings Work Mode Sets work mode for 11g, or 11b, or 11b/g.Default setting is 11g. Region Selection Chooses the country region based on the current region. TX Rate Sets data transfer rate. Default setting is auto mode. For 802.
Close RF Disables or enables the RF. RTS/CTS Threshold Sets RTS/CTS Threshold for integer from 0 to 2347. Fragment Threshold Sets Fragment Threshold for integer from 256 to 2346. Use WMM Disables or enables the WMM. When WMM is enabled, NO ACK or AC can be triggered. 3.2.4 WAI Certificate Certificate window is shown in figure 3-4.The meaning of the field is shown in table 3-4.
3.2.5 Profile Management Profile window is shown in figure 3-5.The meaning of the field is shown in table 3-5. Figure 3-5 Profile Management Table 3-5 Meanings of the Profile Field Field Meanings Delete Apply one profile of the list. When the network is in existence, click apply button to join the network. Other wise, this creates a new network when the network is IBSS. Deletes one profile of the list. Delete All Deletes all profiles of the list. Apply 3.2.
Figure 3-6 Statistics Table 3-6 Meanings of the Statistic Field Field Meanings Total Transmit This shows the number of packets transmitted from the adapter totally Transmit Transmit Bytes This shows the number of packets transmitted from the adapter successfully. This shows the number of bytes transmitted from the adapter totally. Total Receive This shows the number of packets received by the adapter totally. Receive This shows the number of packets received by the adapter successfully.
Figure 3-7 Device Choice 3.3 Windows XP Configuration Utility Notice: Please skip over this section when your operating system is not Windows XP. The steps for connection to the wireless network using Windows Zero Configuration: (1)Click the wireless network icon in the system tray, the Windows XP Wireless Utility window will open, as shown in figure 3-9. CEC Huada Electronic Design Co.
Figure 3-9 Wireless Network Icons (2)Choose a wireless network you want to connect. If the network is open, the message box as warning is shown in figure 3-10.Click Connect Anyway to continue, click Cancel to end the connection. Figure 3-10 Clue on the Wireless Network Connection (3) When the wireless network is connected, the status is shown in figure 3-11. CEC Huada Electronic Design Co.
Figure 3-11 Wireless Network Connection Status (4) If the network is encrypted, you should enter the pass phrase. You can configure your network though the Change advanced setting item which locates the left of the wireless network connection window. 4 Examples for Configuration the Wireless Network This clause introduces how to use AirQuick Wireless Network Config Tool to connect to the network, and how to create a network. 4.
authentication method to join the network. Figure 4-1 Network Item (2)Click the Connect button or double-clicking on the item, Security Option Setting window will appear, as shown in figure 4-2. We should select the correct configurations based on the AP. For example, the network which we connect, the Authentication Type is Open, Encryption Mode is WEP64, and Key Type is Hex Number. We should select the correct configurations.
Figure 4-2 Security Option Setting (3)Click OK button to start the process the authentication. When we join the network successfully, the window as shown in figure 4-3 will appear. Figure 4-3 Connection Success CEC Huada Electronic Design Co.
4.2 Example2 Connecting to the WPA2 Network Notice: You will need to know the passphrase before joining an existing network. (1) As shown in figure 4-4, we select the network which SSID is netcore. Though the authenticate type of the network, we can conclude it is the WPA2 network. Figure 4-4 Network Item (2)Click the Connect button or double-clicking on the item, Security Option Setting window will appear, as shown in figure 4-5.
Figure 4-5 Security Option Setting (1) Click OK button to start the process the authentication. When we join the network successfully, the window as shown in figure 4-6 will appear. Figure 4-6 Connection Success CEC Huada Electronic Design Co.
4.3 Example3 Creating the WAPI Ad hoc (1) Click the Create Ad hoc button in the Network Manage tab, the Network Creating Setting window will appear, as shown in figure 4-7. Figure 4-7 Network Creating Setting (2)We select Authenticate Type for WAI-PreShareKey, select Encryption Mode for WPI. We should select the Key Type and Channel, and enter the SSID and pass phrase.
Figure 4-8 Configuration Network (3)Click the OK button to show the Link Info window, as shown in figure 4-9. Figure 4-9 Creating Network Success CEC Huada Electronic Design Co.
4.4 Example4 Creating the WEP Ad hoc (1)Click the Create Ad hoc button in the Network Manage tab, the Network Creating Setting window will appear, as shown in figure 4-7. (2)We select Encryption Mode for WEP64. We should select the Key Type and Channel, and enter the SSID and pass phrase. For example, we set SSID for test, select Channel for 1, and select Key Type for ASCII Code.
Figure 4-11 Creating Network Success CEC Huada Electronic Design Co.
5 Addendum 5.1 Frequently Asked Questions 1. What’s the IEEE 802.11 standard? Answer:IEEE802.11 standard is a industrial standard of wireless network.IEEE802.11standard is used to ensure different devices of wireless network are compatible with each others. 2. What’s WEP? Answer:As IEEE802.11standard describes,WEP(Wired Equivalent Privacy) is a Data Encrpytion Mechanism based on the 40 bytes sharekey arithmetic. 3.
Country Channel Area 0：North American CH1~CH11 1：Canada CH1~CH11 2：Europe CH1~CH13 3：Spain CH10~CH11 4：France CH10~CH13 5：Japan CH1~CH14 CEC Huada Electronic Design Co.
5.3Technical terms explanation ∷ WLAN:the abbreviation of Wireless Local Area Network. ∷ AP（ （Access Point） ）:wireless Access Point. ∷ SSID：also be abbreviated with ESSID，it’s denotation character of AP. ∷ Point to point Mode（Ad-hoc） ）：point to point network mode in IEEE 802.11g standard，it can be formed without AP.A few network interface cards can compose a network group,of course they must have the same SSID and channel to insure they can connect.
Figure5-2 Infrastructure ∷ IEEE 802.11b：IEEE 802.11b Standard defined the Physical Layer used as data transfers in WLAN and Medium Access Control Sublayer,it adopted 2.4GHz wireless frequency in Physical Layer and the most speed may reach 11Mbps. ∷ IEEE 802.11g：IEEE 802.11g Standard is the successor of IEEE 802.11b Standard,the data transfers speed can achieve 54 Mbps.IEEE 802.11g Standard can also resolve the disturbance problem between Bluetooth products and IEEE802.11b products.
encryption, IEEE802.11X/EAP authentication and PSK techniques,but also support AES(a new security mode)。 ∷ PSK(Per-shared Key)： Wi-Fi Protected Access（WPA）personal mechanism. ∷ TKIP(Temporal Key Integrity Protocol)：a wireless security encryption mechanism of Wi-Fi Protected Access. ∷ AES(Advanced Encryption Standard)：higher encryption mechanism，it uses Symmetrical Block Encryption technique,it’s the preferred standard to use in commerce and government.The standard is used to achieve WPA2.
FCC ID：W2STL0901GU Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.
