Mini PTZ Network Fixed Dome Cameras Quick Guide V1.
Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE! Before you start, connect all the needed cables and cut off the copper wires for the cables that you don't use. Please use self-adhesive waterproof tape (supplied with some products) to protect the cables. Use waterproof components to protect the network cable.
. Install the supplied waterproof components to the network cable in sequence. CAUTION! You need to mount the rubber ring onto the network cable interface first. 4. If your camera has a DC cable and you will not use it, insert the plug into the interface. DC interface Plug 5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately). CAUTION! The cable connector must not be exposed and must be kept away from water.
1 Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details. Item 2 Quantity Camera 1 User document 1 Accessory pack 1 Safety and Compliance Information 2.1 Installation Make sure the camera operates in an environment where the temperature and humidity meet requirements. Keep the camera from excessive pressure, vibration, moisture, dust, and intensive electromagnetic radiation.
Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. 2.2 Maintenance Caution: There will be risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. If there is dust on the glass window surface, remove the dust gently using an oilfree brush or a rubber dust blowing ball.
∅129.0mm (5.1") ø108.5mm (4.3") 143.6mm (5.7") 3-ø4.0mm (0.16") S100.0mm (3.9") 1/4-UNC-2B 3.2 Cable Connection The appearance and tail cable may vary with device model. Third-party device connected through RS485 interface IP Network Power adapter ALM_OUT_P/ALM_OUT_N/ALM_INPUT/GND NOTE! For specifications, see the latest product datasheet. 4 Mount Your Camera 4.1 (Optional) Insert Micro SD Card To use the local storage function, you need to install a Micro SD card into the camera.
Insert the SD card along the arrow direction Open the slot cover 4.2 Ceiling Mount You may adopt ceiling mount or wall mount as needed. Prepare hardware accessories by yourself. The following part takes ceiling mount as an example. Wall mount is similar to ceiling mount and therefore is omitted here. Make sure that the wall is capable of supporting the weight of the camera. 1. Uninstall the adapter plate. Hold the camera, rotate the adapter plate counterclockwise to detach it from the camera.
3. Fix the adapter plate to the ceiling. Knock expansion bolts into holes, and fix the plate to the ceiling with screws. Make sure that FRONT on the plate is in monitoring direction. 4. Install the camera. Secure the camera to the adapter, align FRONT on the plate with the gap between OPEN and LOCK on the camera, rotate the camera counterclockwise until it’s fastened.
NOTE! Lead the cable through the side slot opening on the camera to secure the cable, so that you may avoid opening a hole on the ceiling. Disconnect from power before intalling or uninstalling Micro SD card. Otherwise, the device or the Micro SD card might be damaged. For recommended SD card specifications, contact your dealer or technical support. 5 Startup Check that the device is properly installed, then connect power to start up the device.
Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and noninfringement. Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus.
Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked. Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions.
Use a UL certified power supply that meets LPS requirements if an adapter is used. Use the recommended cordset (power cord) in accordance with the specified ratings. Only use the power adapter supplied with your device. Use a mains socket outlet with a protective earthing (grounding) connection. Ground your device properly if the device is intended to be grounded.
Si le compartiment de la batterie ne se ferme pas en toute sécurité, cessez d’utiliser le produit et gardez-le à l’écart des enfants. Si vous pensez que des piles ont pu être avalées ou placées à l’intérieur d’une partie du corps, consultez immédiatement un médecin. Regulatory Compliance FCC Statements This device complies with Part 15 of the FCC Rules.