Network Bullet Cameras Quick Guide Vl.
Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE! the cables that you don't use. Please use self-adhesive waterproof tape (supplied with some products) to protect the cables. Use waterproof components to protect the network cable. Waterproof the power cable separately if you don’t use it. The video cable does not need waterproof treatment. 1.
Tighten Tighten Tighten Tighten Waterproof tape Wrap the used cables separately Wrap the unused cables together into a bundle 3. Install the supplied waterproof components to the network cable in sequence. CAUTION! You need to mount the rubber ring onto the network cable interface first. 4. If your camera has a DC cable and you will not use it, insert the plug into the interface. 5.
1 Packing List Contact your local dealer if the package is damaged or incomplete. The package contents may vary with device model. No. 2 Name Qty Unit 1 Camera 1 PCS 2 User manual 1 Set 3* Accessory pack 1 Set Safety Instructions Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the safety instructions before installation and operation. 2.1 Precautions Use a power adapter or a PoE device that meets requirements.
Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair ormaintenance. 2.2 Maintenance If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
3.2 Cables The appearance and tail cable may vary with device model. Power interface Network interface IP Network NOTE! 4 For specifications, see the latest product datasheets. Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise. Mount Your Camera 4.
Micro SD slot 4.2 Wall Mount You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself. The following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1. Locate the positions of theholes. 1 Paste installation positioning stickers on the wall and align the cross center to the hole in the wall. 2 Lead the cables across the hole on the wall. 2. Drill holes on the wall. 1 Use a Ø6-6.5mm drill bit.
Knock the plastic rivets into the guide holes and ensure that they are tightened up. 4. Screw the locknut to loosen the universal joint before attaching your camera to the wall. Locknut 5. Mount your camera onto the wall and connect all cables. Lead tapping screwsthrough the guide holes in the base and fix them on the wall by using ascrewdriver. 6. Attach the rubber sheath to the antenna. Antenna Interface Rubber Sheath 7. Rotate the antenna to the antenna interface according to clockwise direction.
Antenna Interface Antenna Reset 8. Adjust the monitoring direction. 1 3 2 1 Adjust the opening of the universal joints as required. 2 Rotate the spherical hinge of the camera to get the desired monitoring direction. 3 Tighten the locknut. 9. Power on your camera and adjustimages. NOTE! The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall.
NOTE! DHCP is enabled by default. If a DHCP server is used in your network, your camera may be assigned an IP address, and you need to use the assigned IP address to log in. You may need to install a plug-in at your first login. Please follow the on-screen instructions to complete the installation and then open the browser again to log in. The default password is intended only for your first login. To ensure security, please change the password after your first login.
About This Manual This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this manual may be different from the actual appearances, functions, features, etc, of the product.
This manual is intended for multiple software versions, and the illustrations and descriptions in this manual may be different from the actual GUI and functions of the software. Despite our best efforts, technical or typographical errors may exist in this manual. cannot be held responsible for any such errors and reserves the right to change the manual without prior notice. Users are fully responsible for the damages and losses that arise due to improper operation.
Keep firmwareuptodate: It is recommended that your device is always upgraded to the latest version for the latest functions and better security. Visit official website or contact your local dealer for the latest firmware. The following are recommendationsfor enhancing network security of your device: Change password regularly: Change your device password on a regular basis and keep the password safe. Make sure only the authorized user can log in to the device.
Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc. Make sure the device is securely installed or placed on a flat surface to prevent falling. Unless otherwise specified, do not stackdevices. Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space forventilation.
Disposer d’une batterie dans le feu ou un four chaud, écraser mécaniquement ou couper la batterie. Disposer la batterie utilisée conformément à vos règlements locaux ou aux instructions du fabricant de la batterie. Regulatory Compliance FCC Statements This device complies with Part 15 of the FCC Rules.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matériel est conforme aux limites de dose d'exposition aux rayonnements, CNR-102 énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec distance minimale de 20 entre le radiateur et votre corps.
Battery in the product complies with the European Battery Directive 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point.
