User's Manual

ManualsBrandsCCT Tech Advanced Products ManualsElectronics5.8GHz Cordless Phone

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is

"receiving" the interference).

• Reorient or relocate and increase the separation between the telecommunications

equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit different from that to

which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an experienced

radio/television technician for additional suggestions. Also, the Federal Communications Commission

has prepared a helpful booklet, "How To Identify and Resolve Radio/TV Interference Problems." This

booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify

stock number 004-000-00345-4 when ordering copies.

Licensing

Licensed under US Patent 6,427,009

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

US Number is located on the cabinet bottom

REN number is located on the cabinet bottom

TABLE OF CONTENTS

Equipment Approval Information .................................. 1

Interference Information ................................................ 1

Licensing ......................................................................... 2

Hearing Aid Compatibility (HAC) ...................................2

FCC RF Radiation Exposure Statement ....................... 3

Introduction ..................................................................... 4

Features ................................................................... 4

Handset Layout ............................................................... 5

Base Layout .................................................................... 5

Parts Checklist ................................................................ 5

Telephone Jack Requirements ................................. 6

Installation ....................................................................... 6

Installation Guide Lines .................................................... 6

Installing The Phone ................................................. 6

Installing The Handset Battery ................................. 6

Connecting the AC (Electrical) Power ...................... 7

Wall Mounting ........................................................... 7

Room Monitor ........................................................... 7

Programming the Telephone ......................................... 8

Handset Setup .......................................................... 8

Language .................................................................. 8

Handset Name .......................................................... 9

Ringer Tone .............................................................. 9

Ringer Volume .......................................................... 9

VIP Melody ............................................................... 9

Storing VIP Melody ................................................... 10

Changing a Stored VIP Melody Record .................... 10

Reviewing and Deleting Stored VIP Melody Record. 10

Set Tone/Pulse ......................................................... 10

Key Tone ................................................................... 11

Area Code ................................................................ 11

Voice Mail # .............................................................. 11

Registration .............................................................. 11

De-Registration ......................................................... 12

Global De-registration ............................................... 12

Default Setting .......................................................... 12

Telephone Operation ...................................................... 13

Charge Indicator ....................................................... 13

Making Calls ............................................................. 13

Answering Calls ........................................................ 13

Call Timer ................................................................. 13

Pre-Dialing ................................................................ 13

Auto Standby ............................................................ 13

Ringer HI/LOW/OFF ................................................. 13

Flash/Voice Mail ....................................................... 14

Last Number Redial .................................................. 14

Exit ............................................................................ 14

Page ......................................................................... 14

Handset to Handset Paging ...................................... 14

Paging All Handset from a Handset .......................... 15

Paging from the Base Group Page ........................... 15

Mute .......................................................................... 15

Hold .......................................................................... 15

Receiver Volume Control .......................................... 15

Do Not Disturb (DND) ............................................... 15

Handset Speakerphone Operation ........................... 16

Answering a Call with the Handset ........................... 16

Making a Call with the Handset ................................ 16

Intercom Operation ......................................................... 16

Making an Intercom Call ........................................... 16

Receiving an Intercom Call ....................................... 17

Advanced Intercom Features ................................... 17

Using Intercom with External Telephone Calls ......... 17

Two-Way Calling ....................................................... 17

Three-Way Calling .................................................... 17

Transferring External Calls to Other Handset ........... 18

Memory ............................................................................ 18

Storing the Last Number Dialed ............................... 18

Introduction

CAUTION: When using telephone equipment, there are basic safety

instructions that should always be followed. Refer to the IMPORTANT SAFETY

INSTRUCTIONS provided with this product and save them for future reference.

Features:

•

• Multi-Handset Phone System

• EZ Read Caller ID Backlit Display

• Bright Backlit Keypad

• Full Duplex Handset Speakerphone

• Call-Waiting Caller ID Compatible

• Voice Mail Indicator

• One-Touch Voice Mail Access

• 60 Name and Number Phone Book

• Do Not Disturb Ringer Option

• Ten Melodic Ring Tones

• Supports up to four handsets

• 3-Way Conference/Call Transfer

• Room Monitoring (requires at least two handsets)

• Headset Jack Option

Your Caller ID Call Waiting phone allows you to:

• View the name and telephone number of a caller (Call Waiting Caller ID) while you are on

the phone.

• Identity callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 40 caller ID messages sequentially.

• Know who called while you are on the other line or when you were away.

• Screen unwanted calls, eliminate harassment from annoying calls, or to get prepared

before answering a call.

IMPORTANT: Because cordless phones operate on electricity, you should have at least

one phone in your home that isn't cordless, in case the power in your goes out.

Handset Layout

816-555-1234

CHRIS LABOI

SOUND ENHANCED DESIGN

EZ-READ LCD DISPLAY

CID/VOL UP/DOWN

BUTTON

FLASH/ONE TOUCH

VOICE MAIL ACCESS BUTTON

MEMORY BUTTON

KEYPAD BUTTONS

PAUSE BUTTON

REDIAL BUTTON

PAGE/INTERCOM

BUTTON

EXIT BUTTON

DELETE/MUTE

BUTTON

FORMAT/HOLD

BUTTON

SPEAKERPHONE

BUTTON

MENU BUTTON

TALK BUTTON

VISUAL MESSAGE

ALERT ANTENNA

BELT CLIP

Base Layout

DO NOT DISTURB BUTTON

VOICE MAIL/CHARGE INDICATOR

PAGE BUTTON

Parts Checklist

Telephone Jack Requirements

To use this phone, you need an RJ11C type modular telephone jack, which might look like the one

pictured here, installed in your home. If you don't have a modular jack, call your local phone company

to find out how to get one installed.

Installation

INSTALLATION NOTE: Some cordless telephone operate at frequencies that may cause

or receive interference with TVs, microware Ovens, and VCRs. To minimize or pervert

such interference, the base of the cordless telephone should not be placed near or on top of

a TV, microware ovens, or VCR. If such interference continues, more the cordless telephone

farther away from these appliances. Certain Other communications devices may also use

with each other and/or your new telephone. If you are concerned with interference, please

refer to the owner's manual for these devices on how to properly set channels to avoid

wireless audio/video senders, wireless computer networks, multi-handset cordless telephone

system, and some long-range cordless telephone system.

• Never install telephone waiting during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is specifically designed for wet

location.

• Never touch non-insulated telephone wiles or terminals, unless the telephone line has

been disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Temporarily disconnect any equipment connected to the phone such as faxes, other phones,

or modems.

Installation Guide Lines

• Install telephone near both a telephone (modular) jack and an electrical power outlet.

• Avoid sources of noise, such as a window by a busy street, and electrical noise, such as motors,

microwave ovens, and fluorescent lighting.

• Avoid heat sources, such as heating air ducts, heating appliances, radiators, and direct sunlight.

• Avoid areas of excessive moisture or extremely low temperatures.

• Avoid dusty locations,

• Avoid other cordless telephones or personal computers.

Installing the Phone

Choose the best location to install your bass and handset charge cradle. Your base

and handset charge cradles should be placed on a level surface such as a desk or

table top.

Installing the Handset Battery

NOTE: You must connect the handset battery before use.

Modular

telephone

line jack

Wall plate

1. Locate battery and battery door which are packaged

together inside a plastic bag and are separate from the

handset.

2. Locate the battery compartment on the back of the handset.

3. Plug the battery pack cord into the jack inside the

compartment.

NOTE: It is important to maintain the polarity (black and red wires) to the jack

inside the compartment. To ensure proper battery installation, the connector is

keyed and can be inserted only one way

4. Insert the battery pack.

5. Close the battery compartment by pushing the door up until it snaps into place.

6. Place the handset in the charging cradle.

Connecting the AC (Electrical) Power

1. On the base, plug one end of the power adaptor cord into the power jack on the back of the

base and the other end into an electrical outlet.

CAUTION: Use only the COMTREK power adaptor that came with this unit. Using

other power supplies may damage the unit.

2. Plug the handset charge cradle into an electrical outlet.

NOTE: When the handset is placed in the cradle, the charge indicator on the base and

the charge indicator on the handset charge cradle turns on to indicate the handset

battery is charging. Connecting the Telephone Line On the base, plug the one end

of the telephone line cord into the jack on the back of the base and the other end

into a modular wall phone jack.

Wall Mounting

If you want to mount the phone on a wall, slip the mounting holes (on the back of the base) over the wall

plate posts, and slide the unit down into place. (Wall plate not included.)

Room Monitor (requires two handset)

1. Make sure your phone is OFF (not in talk mode).

2. Press the MENU button to go to the main menu.

3. Press CID/VOL ( or ) button to scroll to ROOM MONITOR.

4. Press MENU button to enter ROOM MONITOR menu, ROOM MONITOR EXTENSION? shows in

the display.

5. Use the touch tone pad to enter the handset number to be monitored, either 1 or 2.

Handset Unit AC Adaptor

Wall MountTelephone Line Belt ClipBattery Pack

6. The receiving handset will turn on the microphone and the originating handset will turn on the

earpiece to monitor sound from the receiving handset.

NOTE: For room monitoring mode to work, the originating handset must NOT be on the cradle.

It will exit room monitor mode if it is on the cradle.

NOTE: While in room monitoring mode, the handsets will emit an alert tone approximately

every 5 seconds if there is an incoming call. You may press the TALK/END/CALL BACK button

to quit room monitor and answer the call.

NOTE: While in room monitoring mode, the originating handset can be switched to monitor by

speaker mode by pressing the SPKR button once. Switch back to earpiece by pressing the

TALK/END/CALL BACK button once.

NOTE: Press the *EXIT button on the handset to exit room monitor mode.

Programming the Telephone

Standby Screen

The handset displays the handset number and user name.

USER NAME

HANDSET *

Programming Functions

The system uses a menu structure to give you access to all of the built-in features. You may program

the following items in main menu:, Handset Setup, Room Monitor (only available with 2 or more handset).

HANDSET SETUP

ROOM MONITOR

Handset Setup

1. Make sure your phone is OFF (not in talk mode).

2. Press the MENU button to go to the main menu.

3. Press MENU button to confirm and you may program the following items:

Set Language, Handset Name, Ringer Tone, Ringer Volume, VIP Melody, Set Tone / Pulse,

Key Tone ON/OFF, Area Code, Voice Mail #, Registration, Deregistration and Default Setting.

During programming, you may press the *EXIT button at any time to exit the menu and

return to the sub-menu. Make sure your phone is OFF (not in talk mode).

Language

1. Press the CID/VOL ( or ) button to scroll to the SET LANGUAGE menu.

2. Press MENU button to enter the menu. SET LANGUAGE 1ENG 2FRA 3ESP shows in the display.

3. Use the touch tone pad on the handset to select 1ENG, 2FRA, 3ESP, or use the CID/VOL

( or ) button to scroll to the desired language. English is the default setting.

4. Press the MENU button to save your selection. You will hear a confirmation tone and the selected

language shows in the display.

Handset Name

1. Press the CID/VOL ( or ) button to scroll to the HANDSET NAME menu.

2. Press MENU button to enter the menu. HANDSET NAME shows in the display.

3. Use the touch-tone pad to enter a name (up to 15 characters). More than one letter is

stored in each of the number keys. For example, to enter Bill Smith, press the 2 key twice for the

letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L. Press the

5 key 3 times for the second letter L, and press the 1 key to insert a space between the first and

last name. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press the

4 key 3 times for the letter I; press the 8 key for the letter T; press the 4 key twice for the letter H.

NOTE: If you make a mistake, use the DEL/MUTE button to backspace and delete

one character at a time.

4. Press the MENU button to save your name. You will hear a confirmation tone and the

handset name shows in the display.

Ringer Tone

You may choose from ten different ringer tones (01 to 10) and ten different melodies (11 to 20).

1. Make sure the ringer is turned on. See Ringer On/Off section.

2. Press the CID/VOL ( or ) button to scroll to the RINGER TONE menu.

3. Press MENU button to enter the menu. SET RINGER TONE 01 shows in the display. "01" is

default setting.

4. Use the CID/VOL ( or ) button to scroll to the desired setting (1 through 20). You will hear a

sample of the ringer tone/melody you select.

5. Press the MENU button to save your selection. You will hear a confirmation tone and the selected

ringer tone shows in the display.

Ringer Volume

1. Press the CID/VOL ( or ) button to scroll to the RINGER VOLUME menu.

2. Press MENU button to enter the menu. SET RINGER 1HI 2LOW 3OFF shows in the display.

3. Use the touch tone pad on the handset to select 1, 2 or 3, or use the CID/VOL ( or ) button to

scroll to your selection. "1HI" is the default setting.

4. Press the MENU button to save your selection. You will hear a confirmation tone and the new

volume setting shows in the display.

NOTE: If you turn the ringer OFF, the ringer off icon shows in the display.

VIP Melody

This features allow you to assign a specific melody to someone you want to get your attention when the

person calls. When a VIP melody is assigned and that person calls, the unit rings the normal ring for

the first ring and then follows with VIP melody ring. You may choose from ten different polyphonic

melodies and may store up to 10 VIP records.

NOTE: This feature ONLY works when the following conditions are met.

1. You have subscribed to Caller ID.

2. You have your Caller ID record previously transferred to the memory. (Refer to Storing CID

Records in Internal Memory). "NO USER MEMORY" will show in the display to remind the user to

do CID record transfer first.

Storing VIP Melody

1. With handset in standby mode.

2. Press MENU button once to display the submenus; HANDSET SETUP and ROOM MONITOR..

3. Press MENU button to enter into HANDSET SETUP.

4. Press the CID/VOL ( or )button to scroll to VIP MELODY submenu.

5. Press MENU button to select VIP melody feature and then display VIP 1 record.

• If VIP1 does NOT contain any specific number/records, it will display EMPTY.

6. Press CID/VOL ( or ) button to select the specific VIP melody memory location (10 VIP

locations) that does not contain any record.

7. Press MENU button to display SELECT MEMORY.

NOTE: If the memory location does not contain any CID memory records and you are

trying to mark a specific record as VIP MELODY, then "SELECT MEMORY" will not

be displayed. Instead, "NO USER MEMORY" will display in prompt to alert the user.

8. Press CID/VOL ( or ) button to view the records from memory to be selected as VIP.

9. Press MENU button to confirm and then display VIP MELODY 01 to wait for the melody tone

selection.

10. Press CID/VOL ( or ) button to select from melody 01 to melody 10 (a testing tone is

generated while making melody selection)

11. Press MENU button to confirm.

NOTE: If the desired number/record was previously stored in any one of the ten VIP

melody records, "DUPLICATE NUMBER" shows in the display.

Changing a Stored VIP Melody Record

Use the Storing VIP Melody procedure to change the number of a selected record and replace the old

phone number with new phone number.

When REPLACE VIP# ? shows in the display, you must press MENU button on the handset to confirm

replacement.

Reviewing And Deleting Stored VIP Melody Record

1. Press the MENU button to enter to VIP MELODY menu.

2. Use the CID/VOL ( or ) button to scroll to the desired VIP Melody Record.

3. If you want to delete the information, press the DEL/MUTE button on the handset while the

entry displays. The display show DELETE VIP# ?.

4. Press DEL again to confirm. You will hear a confirmation tone and VIP# DELETED show in the

display.

Set Tone / Pulse

1. Press the CID/VOL ( or ) button to scroll to the SET TONE/PULSE menu.

2. Press MENU button to enter the menu. SET TONE/PULSE 1TONE 2PULSE shows in the

display.

3. Use the touch tone pad on the handset to select 1or 2 , or use the CID/VOL ( or )

button to scroll to your selection. "1TONE" is the default setting.

4. Press the MENU button to save your selection. You will hear a confirmation tone and the new

volume setting shows in the display.

Key Tone

1. Press the CID/VOL ( or ) button to scroll to the KEY TONE menu.

2. Press MENU button to enter the menu. SET KEY TONE 1ON 2OFF shows in the display.

3. Use the touch tone pad on the handset to select 1 or 2, or use the CID/VOL ( or )

button to scroll to your selection. "1ON" is the default setting.

4. Press the MENU button to confirm and the key tone setting shows in the display.

Area Code

1. Press the CID/VOL ( or )button to scroll to the AREA CODE menu.

2. Press MENU button to enter the menu. SET AREA CODE - - - shows in the display.

3. Use the touch-tone pad to enter your 3-digit area code.

4. Press the MENU button to confirm. You will hear a confirmation tone and the new area

code shows in the display.

NOTE: To restore the default setting to - - -, press and release DEL when "SET

AREA CODE" shows in the display.

One-Touch Voice Mail Access

This function can use if you have subscribed to telco voice mail service.

1. Press the CID/VOL ( or )button to scroll to the VOICE MAIL # menu.

2. Press MENU button to enter the menu. SET VOICE MAIL# shows in the display.

3. Use the touch-tone pad to enter the voice mail number and it can up to 20 numbers.

4. Press the MENU button to confirm. You will hear a confirmation tone and the voice mail #

shows in the display.

5. To include a PIN number after voice mail number, use PAUSE button to add dialing example

555-555-1212pp1234.

6. Then, it will exit to program sub-menu screen.

Registration

This setting may be made with the handsets. Your handset is pre-registered and ready to use. It is not

recommended that handset be registered again unless absolutely necessary.

1. If necessary, press the MENU button to go to the REGISTRATION menu. The default is "2NO".

2. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the CID/VOL ( or ) button to

scroll to 1YES or 2NO.

3. If you select 1YES, press the MENU button to confirm your selection. HOLD BASE PAGE WAIT

FOR BEEP shows in the display.

4. Press and hold the page button on the base unit until you hear a long tone at the handset.

HANDSET X REGISTERED shows in the handset display, where X is the handset name. You will

hear a confirmation tone.

De-Registration

This setting may be made with the handsets. De-registration cancels registration. During the de-regis-

tration process, keep the handset near the base.

1. If necessary, press the MUTE/PROG button to scroll to the DEREGISTRATION menu. The

default is "2NO".

2. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the CID/VOL ( or ) button to

scroll to 1YES or 2NO.

WARNING: It is not recommended that a handset be de-registered unless absolutely

necessary because once a handset is de-registered, that handset's telephone features

cannot be used until the handset is re-registered.

3. Select NO, if you do not want to de-register.

4. If you select 1YES, press the MUTE/PROG button and MOVE NEAR TO BASE displays for 2

seconds, then CONFIRM? 1YES 2NO appears in the display.

5. Press the touch-tone pad to select 1YES or 2NO, or use the CID/VOL ( or ) button to scroll to

1YES or 2NO.

6. If you select YES, press the MENU button to confirm. You will hear a confirmation tone.

Then HANDSET X DEREGISTERED shows in the display to confirm the handset is deregistered.

NOTE: When you complete the de-registration process, "HANDSET NEEDS

REGISTRATION" shows in the display. To use the handset, you must register the

handset.

Global De-registration

If one or more handsets becomes lost, you should de-register all handsets to ensure proper system

operation. Follow the steps below to de-register both handsets at the same time.

WARNING: It is not recommended that a handset be de-registered unless absolutely necessary be-

cause once a handset is de-registered, that handset's telephone features cannot be used until the

handset is re-registered.

1. Press and hold the page button on the base until the IN USE/CHARGE indicator on the base

flashes.

2. Press and hold the page button on the base again until the IN USE/CHARGE indicator on the

base flashes rapidly.

3. Press and release the page button on the base once. All handsets are de-registered and

HANDSET NEEDS REGISTRATION shows in the display.

Default Setting

As you become familiar with this system, you may prefer to use the system's original settings. Follow

the steps below to return to the factory default settings.

1. Press the CID/VOL ( or ) button to scroll to the DEFAULT SETTING menu.

2. Press the MENU button to enter the menu. DEFAULT SETTING 1YES 2NO shows in the display.

3. Use the touch-tone pad to select 1YES or 2NO, or use the CID/VOL ( or ) button to move the

cursor to 1YES or 2NO. "2NO" is default setting.

NOTE: If you choose YES all the settings in the programmable menu are returned to

factory default setting.

4. Press the MENU button to save your selection. You will hear a confirmation tone.

Telephone Operation

Charge Indicator

When the Voice Mail /Charge indicator is lit, the handset is correctly seated in the cradle and is charging.

Making Calls

1. Pick up the handset, and press the TALK button. Listen for a dial tone.

2. Dial the number you want to call, or dial the number first then press the TALK button.

3. When finished, press the TALK button to hang up.

Answering Calls

1. When the phone rings, pick up the handset, and press the TALK button.

2. When finished, press TALK button to hang up.

NOTE: Adjust the handset volume by pressing the CID/VOL ( or ) button during a call.

Call Timer

After you press the TALK button on the handset, the built-in call timer shows on the display and counts

the length of time of the call in minutes and seconds.

Pre-Dialing

1. Make sure the phone is OFF (not in talk mode).

2. Enter the telephone number you want to call. The telephone number shows in the handset display.

3. Press the TALK button on the handset, and the number automatically dials.

NOTE: You may enter up to 32 pre-dial digits.

NOTE: If you want to delete the pre-dial number you entered, press the DEL/MUTE

button until all of the digits are erased.

Auto Standby

If you place the handset in the cradle while the handset is off the hook (during a call), the call is

automatically disconnected.

Ringer HI/LOW/OFF

There are two ways to set the ringer to HI/LOW/OFF. One is the traditional way as described in the

MEUN Functions; Handset Setup; Ringer Volume menus. The other one is this short cut to ringer

menu.

1. Make sure the phone is OFF (not in talk mode).

2. Press the #PAUSE button to display 1HI 2LOW 3OFF.

3. Use the touch tone pad on the handset to select 1, 2 or 3, or use the CID/VOL ( or ) button to

scroll to your selection. "1HI" is the default setting.

4. Press #PAUSE button again to save and display the new selection for a few seconds.

Cordless Phone System with

EZ-READ Caller ID

Equipment Approval Information

Your telephone equipment is approved for connection to the Public Switched Telephone Network and

is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for

Telephone Terminal Equipment published by ACTA.

1 Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US number and

Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this informa-

tion to your telephone company.

The REN is useful in determining the number of devices you may connect to your telephone line and

still have all of these devices ring when your telephone number is called. In most (but not all) areas, the

sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number

of devices you may connect to your line as determined by the REN, you should contact your local

telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must

comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug is provided with this product. It is designed to be connected to a

compatible modular jack that is also compliant. See installation instructions for details.

Notes

• This equipment may not be used on coin service provided by the telephone company.

• Party lines are subject to state tariffs, and therefore, you may not be able to use your own

telephone equipment if you are on a party line. Check with your local telephone company.

• Notice must be given to the telephone company upon permanent disconnection of your

telephone from your line.

• If your home has specially wired alarm equipment connected to the telephone line, ensure

the installation of this product does not disable your alarm equipment. If you have questions

about what will disable alarm equipment, consult your telephone company or a qualified

installer.

2 Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network, the tele-

phone company shall, where practicable, notify you that temporary discontinuance of service may be

required. Where prior notice is not practicable and the circumstances warrant such action, the tele-

phone company may temporarily discontinue service immediately. In case of such temporary

discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance;

(2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a com-

plaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and

Regulations. or procedures where such action is required in the operation of its business and not

inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or

performance of your telephone equipment, the telephone company must give you adequate notice, in

writing, to allow you to maintain uninterrupted service.

Interference Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference; and (2) This device must accept any interference

received, including interference that may cause undesired operation.

816-555-1234

CHRIS LABOI

Inserting a Pause in the Dialing Sequence ............... 19

Reviewing Records Stored in Memory ..................... 19

Changing Records Stored in Memory ...................... 19

Dialing a Number from Memory ................................ 19

Chain Dialing from Memory ...................................... 20

Caller ID (CID) .................................................................. 20

CID Error Codes ....................................................... 20

Receiving CID Records ............................................ 21

Storing CID Records ................................................. 21

Reviewing CID Records ........................................... 21

Storing CID Records in Internal Memory .................. 21

Dialing a CID Number ............................................... 22

Deleting a CID Record .............................................. 22

Deleting All CID Record ............................................ 22

Changing the Battery ................................................ 23

Battery Safety Precautions ....................................... 23

Belt Clip and Optional Headset ................................ 23

Connecting an Optional Headset to the Handset ..... 23

Display Messages ........................................................... 24

Handset Sound Signals ..................................................25

Troubleshooting Guide .................................................. 25

Caller ID Solution ...................................................... 26

Battery ...................................................................... 26

General Product Care ............................................... 26

Causes of Poor Reception ........................................ 26

Service ............................................................................. 27

Limited Warranty ............................................................. 27

Limitation of Warrant ................................................. 27

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a mininum distance of 20 centimeters between

the radiator and your body. This transmitter must not be co-located or operated in conjunction with any

other antenna or transmitter."

For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines

when used with the belt clip supplied with this product. Use of other accessories may not ensure

compliance with FCC RF exposure guidelines.

Base Unit

MD2400,2420ib-engRev05 5/17/06, 10:42 PMPage 1 Adobe PageMaker 6.5C/PPC

5.8 GHz Digital Multi-Handset

CT5450

5.8

5.8 GHz Digital Spread Spectrum Technology

the 5.8GHz frequency for communication, and, if not properly set, these devices may interfere

interference. Typical devices that may use the 5.8GHz frequency for communication include

5.8

Summary of content (2 pages)

PAGE 1
CT5450 5.8 GHz Digital Multi-Handset Cordless Phone System with EZ-READ Caller ID This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
Flash/Voice Mail If you subscribe to the combined Call Waiting Caller ID service from your local telephone company, you will receive Caller ID information (if available) on Call Waiting calls. During a phone call, you will hear a beep to indicate another call is waiting on the line and Caller ID information for the waiting call shows on the handset display. • To connect to the waiting call, press the FLASH button on the handset, and your original call is put on hold.