User's Manual

26750
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and
Regulations and the Technical Requirements for Telephone Terminal
Equipment published by ACTA.
1. Notification to the Local Telephone Company
On the bottom of this equipment is a label that contains, among other
information, a product identifier in the form US:AAAEQ##TXXXX. You
must, upon request, provide this information to your telephone
company.
The digits represented by ## in the product identifier indicate the
Ringer Equivalency Number (REN) for this equipment. The REN is
useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your
telephone number is called. In most (but not all) areas, the sum of the
RENs of all devices connected to one line should not exceed 5. To be
certain of the number of devices you may connect to your line as
determined by the REN, contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant.
See installation instructions for details.
Notes
♦ This equipment may not be used on coin service provided by the
telephone company.
♦ Party lines are subject to state tariffs, and therefore, you may not
be able to use your own telephone equipment if you are on a
party line. Check with your local telephone company.
♦ Notice must be given to the telephone company upon permanent
disconnection of your telephone from your line.
♦ If your home has specially wired alarm equipment connected to
the telephone line, ensure the installation of this product does
not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your
telephone company or a qualified installer.
2. Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm
the telephone network, the telephone company shall, where
practicable, notify you that temporary discontinuance of service may
be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1) promptly
notify you of such temporary discontinuance; (2) afford you the
opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth
in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may take changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business and not inconsistent with
FCC Rules and Regulations. If these changes are expected to affect
the use of performance of your
HEARING AID COMPATIBLITY (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ON THE CABINET
REN NUMBER IS LOCATED ON THE CABINET
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference; and (2) This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
♦ Reorient or relocate the receiving antenna (that is, the antenna for
radio or television that is “ receiving” the interference).
♦ Reorient or relocate the increase the separation between the
telecommunications equipment and receiving antenna.
♦ Connect the telecommunications equipment into an outlet on a
circuit different from that to which the receiving antenna is
connected.
If these measures do not eliminate the interference, please consult your
dealer or an experienced radio/television technician for additional
suggestions. Also, the Federal Communications Commission has prepared
a helpful booklet, “ How To Identify and Resolve Radio/TV Interference
Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number
004-000-00345-4 when ordering copies.
INTRODUCTION
Your Caller ID phone stores and displays specific information, provided by
your local telephone company, to subscribers of Caller ID or similar caller
identification services. You must subscribe to one of these services in
order to use this unit.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
• Record up to 48 Caller ID messages sequentially.
• Know the caller number while you were away.
To get the most from your new phone, we suggest that you take a few
minutes right now to read through this user's guide.
IMPORTANT: In order to use this unit, you must subscribe to either the
standard Name/Number Caller ID Service.
IMPORTANT: Because cordless phones operate on electricity, you
should have at least one phone in your home that isn’ t cordless, in case
the power in your home goes out.
THE LIGHTNING FLASH CAUTION: TO REDUCE THE RISK OF THE EXCLAMATION POINT
AND ARROW HEAD ELECTRIC SHOCK, DO NOT REMOVE WITHIN THE TRIANGLE
WITHIN THE TRIANGLE COVER (OR BACK). NO USER IS A WARNING SIGN
IS A WARNING SIGN SERVICEABLE PARTS INSIDE. REFER ALERTING YOU OF
ALERTING YOU OF SERVICING TO QUALIFIED SERVICE IMPORTANT
“ DANGEROUS PERSONNEL INSTRUCTIONS
VOLTAGE” INSIDE THE ACCOMPANYING THE
PRODUCT. PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the items:-
1. Base Unit
2. Handset
3. Handset Battery
4. Telephone Line Cord
5. AC Power Supply
MODULAR JACK REQUIREMENTS
You need an USOC Jack RJ11C/BABT 431A type modular phone jack,
which is the most common type of phone jack. If you don’ t have a modular
jack, call your local phone company to find out how to get one installed.
INSTALLATION NOTE: Some cordless telephones operate at frequencies
that may cause interference to nearby TVs microwave ovens, and VCRs.
To minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV, microwave ovens,
or VCR. If such interference continues, move the cordless telephone
farther away from these appliances.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a security system to provide protection against
false ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code.
After a power outage or battery replacement, you should place the handset
in the base for about 20 seconds to reset the code.
INSTALLATION
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
DESKTOP INSTALLATION
1. Remove the battery compartment door of handset.
2. Insert battery pack and connect the cord into the jack inside the
handset.
3. Put the compartment door back on.
4. Place the handset in the base.
5. Raise the base antenna.
6. Plug the adaptor to the socket-outlet that near the equipment
and shall be easily accessible and the other end into the power
jack on the back of the base. The IN USE/ CHARGE indicator
comes on indicating that the battery is charging.
Allow the phone to charge for 12 hours prior to first use. If you
don't properly charge the phone, battery performance will be
compromised.
7. After charging, plug the telephone line cord into the modular jack
and into the LINE jack on the bottom of the base.
8. Set the RINGER program on the handset to ON, (Please see the
details on chapter of Ringer Setting)
Note: The phone automatically defaults to touch-tone dialing.
To change to pulse (rotary) dialing, see “ Tone/Pulse Dialing” . If
you don’ t know which type of service you have, check with the
phone company.
CAUTION: Use only the ATLINKS power supply that came with
this unit. Using other power supplies may damage the unit.
NOTE : The phone is shipped in Tone Dialing Mode from the
manufacturer.
SET UP
TONE/PULSE DIALING
A Tone/Pulse (T/P) switch is located at the bottom of base. T and P are
denoted as Tone and Pulse respectively.
DATE AND TIME SETTING
1. Press and hold the SET TIME/REDIAL button for 3 seconds.
2. Press “▲ ” or “▼ ” button to adjust the month setting.
3. Press SET TIME/PAUSE button to go to date setting
4. Press “▲ ” or “▼ ” button to adjust the date.
5. Press SET TIME/PAUSE button to go to hour setting
6. Press “▲ ” or “▼ ” button to adjust the hour.
7. Press SET TIME/PAUSE button to go to minute setting
8. Press “▲ ” or “▼ ” button to adjust the minute. (or Press EXIT button
exit the program)
9. Press SET TIME/PAUSE button again to confirm setting and go back
to standby mode.
CONTRAST SETTING SELECTION
1. Press and hold the MEM/Prog button for 3 seconds.
2. Press CHANNEL/SELECT button until “ LCd” shows on display.
3. Use the “▲ ” or “▼ ” button to adjust the level
4. Press MEM/Prog to store selection.
5. Press EXIT to quit the program.
RINGER MELODY SELECTION
1. Press and hold the MEM/Prog button for 3 seconds.
2. Press CHANNEL/SELECT button until “ rIng” shows on display.
3. Use the “▲ ” or “▼ ” button to select the ringer. (8 ringer melodies can
be selected)
4. Press MEM/Prog to store selection.
5. Press EXIT to quit the program.
VIP RINGER MELODY SELECTION
1. Press and hold the MEM/Prog button for 3 seconds.
2. Press CHANNEL/SELECT button until “ UIP rIng” shows on display.
3. Use the “▲ ” or “▼ ” button to select the ringer. (8 ringer melodies can
be selected)
4. Press MEM/Prog to store selection.
5. Press EXIT to quit the program.
PAGE RINGER MELODY SELECTION
1. Press and hold the MEM/Prog button for 3 seconds.
2. Press CHANNEL/SELECT button until “ PAgE rIng” shows on display.
3. Use the “▲ ” or “▼ ” button to select the ringer. (8 ringer melodies can
be selected)
4. Press MEM/Prog to store selection.
5. Press EXIT to quit the program.
RINGER ON/OFF
The RINGER setting must be ON for the handset to ring during incoming
calls.
1. Press and hold the MEM/PROG button for 3 secons
2. Press CHANNEL/SELECT button until “ rINgUoL” shows on display
3. Use the “▼ ” button until “ rINgUoL OFF” shows on display.
4. Press MEM/PROG to store selection
5. Press EXIT to quit the program.
VOLUME
While you are on phone, you can press the VOLUME “+” or “-” button to
adjust the volume of the handset’ s earpiece.
CORDLESS PHONE BASICS
RECEIVING A CALL
1. Check the display to see who is calling.
2. Press the LINE
button.
3. Press the LINE
button again to hang up.
MAKING A CALL
1. To make a call, press the LINE
button before you dial
2. Press it again to hang up. –OR-
1. Input the telephone number first.
2. Then press LINE button to dial out the number.
REDIAL
1. Press the LINE button
2. Press “ REDIAL/SET TIME” to redial
DELETING THE CURRENT REDIAL RECORD
1. Make sure the phone is OFF.
2. Use the REDIAL “▼ ” button or press the CHANNEL/SELECT button
3. Press the “▲ ” or “▼ ” button to display a desired redial record.
4. Press FLASH/DELETE button, “ dELEtE” shows on display.
5. Press FLASH/DELETE button again to confirm the deletion. Or press
EXIT button to cancel the deletion.
DELETING ALL REDIAL RECORDS
1. Make sure the phone is OFF.
2. Use the Redial “▼ ” buttons or press the CHANNEL/SELECT button
and displays any redial record.
3. Press and hold FLASH/DELETE button for several seconds. “ dELEtE
ALL” displays on screen.
4. Press FLASH/DELETE button again to confirm the deletion. Or press
EXIT button to cancel the deletion.
IN USE/CHARGE INDICATOR
The phone is ON when the IN USE/CHARGE indicator on the base is lit.
The IN USE/CHARGE indicator on the base flashes when you receive a
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for future
reference.
WARNING:
TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
NOTE :
For desktop charging only, the handset is only able to
charge facing up.