WI-FI weather station with 7-In-1 professional sensor Model: C6075A User Manual INDEX HISTORY MAX MIN CHANNEL
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ABOUT THIS USER’S MANUAL This symbol represents a warning. To ensure safe use, always adhere to the instructions described in this documentation. This symbol is followed by a user’s tip. PRECAUTIONS --Keep and reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any responsibility for any incorrect readings, export data lost and any consequences that occur should an inaccurate reading take place.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSOLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LCD DISPLAY . . . . . . .
INTRODUCTION Thank you for selecting WI-FI weather station with 7-in-1 professional sensor. This system gathers and automatically uploads accurate and detail weather data to Weather Underground and Weathercloud website - the famous weather service which allows weather observers to upload their local weather data with automated personal weather stations (PWS) - at which you can access and upload your weather data freely.
LCD DISPLAY Display section: 1. Outdoor temperature & humidity 2. Wind direction & speed 3. Indoor (Ch) temperature & humidity 4. Weather index 5. UV index & light intensity (SUN) 6. Weather forecast 1 2 3 4 7 5 8 10 6 9 11 7. Calendar & moon phase 8. Time / alarm 9. Barometer 10. Sunrise & sunset time 11. Rainfall & Rain rate WIRELESS INDOOR HYGRO-THERMO SENSOR 1 2 3 4 5 4. [ RESET ] key 5. Battery compartment 1. Transmission status LED 2. Wall mounting holder 3.
WIRELESS 7-IN-1 SENSOR 1 2 3 4 6 7 8 9 10 11 12 13 1. 2. 3. 4. 5. 6. Wind vane Wind cups Antenna Radiation shield Thermo-hygro sensor Mounting parts (fit for 35 ~40mm diameter pole) 7. Battery door 8. [ RESET ] key 9. Transmission status LED 10. Bubble level gradienter 11. Rain collector 12. UV / light sensor 13.
INSTALLATION AND SETUP Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor sensors. (1pc wireless indoor sensor included) INSTALL WIRELESS 7-IN-1 SENSOR Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity, temperature and humidity for you. It’s assembled and calibrated for your easy installation. INSTALL BATTERIES Unscrew the battery door at bottom of unit and insert the batteries according to the +/- polarity indicated.
NOTE: --If you need to re-assign the sensor channel, slide the channel slide switch to the new channel position. For the new channel number to be effective, press [ RESET ] key on the sensor. -- Avoid placing the sensors in direct sunlight, rain or snow. --To avoid the sensor/s and console pairing failure during new console setup, please power up the sensor/s first, and then press [ RESET ] key on the main unit (no need on sensors).
RESYNCHRONIZE SENSORS Press the [ SENSOR / WI-FI ] key once for the console to enter sensor Synchronization mode, and the console will re-register all the sensors that have already been registered to the it before. i.e. the console will not lose the connection of the sensors that you’d paired up before. CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR Whenever you changed the batteries of the wireless indoor or 7-in-1 weather sensor, resynchronization must be done manually. 1.
2. After you have created your account and completed the Email validation, please go back to the WUndergound web page to login. Then, click “My Profile” button on the top to open the drop-down menu and click "My Weather Station". 3. In "My Weather Station" page bottom, press the "Add New Device" button to add your device. 4. Follow their instruction to enter your station information, in the Step "Tell Us More About Your Device", (1) enter a Name for your weather station.
CREATE WEATHERCLOUD ACCOUNT 1. In https://weathercloud.net enter your information in "Join us today" section, then follow the instructions to create your account. NOTE: Use the valid email address to register your account. 2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new device. 3. Enter all the information in Create new device page, for the Model* selection box select the "W100 Series" under "CCL" section.
4. Jot down your ID and key for the further setup step. SETUP WI-FI CONNECTION 1. When you power up the console for the first time, the console LCD will show flashing "AP" and " " icon to signify that it has entered AP (Access Point) mode, and is ready for WI-FI settings. User can also press and hold the [ SENSOR / WI-FI ] key for 6 seconds to enter AP mode manually. 2. Use the smart phone, tablet, or computer to connect the console through WI-FI. 3.
WI-FI CONNECTION STATUS Below is the WI-FI icon status on the console LCD: Stable: Console is in connection with WI-FI router Flashing: Console is trying to connect to WI-FI router Flashing: Console currently in Access Point (AP) mode SETUP THE WEATHER SERVER CONNECTION Enter the following information into the below web interface "SETUP" page to connect the console to weather server, If you do not want to use Wunderground.com or Weathercloud.
TIME ZONE To automtically set the time display to your time-zone, change the time zone in SETUP page of previous section from '0:00' (default) to your time zone (e.g.+1:00 for Germany). Time server setup Server URL: nist.time.gov Time Zone: 0:00 TIME SERVER CONNECTION STATUS After the console has connected to the internet, it will attempt to connect to the internet time server to obtain the UTC time. Once the connection succeeds and the console's time has been updated, the “ ” icon will appear on the LCD.
CALIBRATION 1. User can input the offset and/or gain values for different parameters while current offset and gain values are shown next to their corresponding blank. Apply 2. Once completed, press at the bottom of the SETUP page The current offset value will show the previous value that you entered, please input the new Apply value in the blank if any changes needed, the new value will effective once you press icon in SETUP page.
FIRMWARE UPDATE The console supports OTA firmware update capability. Its firmware may be updated over the air anytime (whenever necessary) through any web-browser on a PC with WI-FI connectivity. Update function, however, is not available through mobile/smart devices. Current firmware version Firmware version: 1.00 Browse Upload Bottom of web interface ADVANCED page Please to select the firmware file for update Press to start upload the firmware to console FIRMWARE UPDATE STEP 1.
NOTE: --In normal mode, press [ CLOCK SET ] key to switch between year and date display. --During the setting, you can press and hold [ CLOCK SET ] key for 2 seconds to back to normal model. DAYLIGHT SAVING TIME (DST) DST function is set to "AUTO" by default (for EU or US version). If the current date on display is with in the summer daylight saving period, the time will will be automically adjusted forward by +1 hour, and DST icon will be shown on the LCD dsiplay.
ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION 1. In normal mode, press [ ALARM ] key to show the alarm time for 5 seconds. 2. When the alarm time displays, press [ ALARM ] key again to activate the alarm function. Or press [ ALARM ] key twice to activate the alarm with ice pre-alarm function. Alarm off Alarm on Alarm with ice-alert NOTE: Once the ice pre-alert activates, the pre-set alarm will sound and ice-alert icon will flash 30 minutes earlier if the outdoor temperature is below -3°C.
VIEW THE OTHER INDOOR CHANNELS (OPTIONAL FEATURE WITH ADD ON EXTRA SENSORS) This console is capable to pair with a wireless 7-IN-1 sensor and up to 7 wireless indoor sensors. If you have 2 or more Indoor sensors, you can press [ CHANNEL ] key to switch between different wireless channels in normal mode, or press and hold [ CHANNEL ] key for 2 seconds to toggle auto-cycle mode to display the connected channels at 4 seconds interval.
2 Light breeze 3 Gentle breeze 4 Moderate breeze 5 Fresh breeze 6 Strong breeze 7 High wind 8 Gale 9 Strong gale 10 Storm 11 Violent storm 12 Hurricane force 6 ~ 11 km/h 4 ~ 7 mph 4 ~ 6 knots 1.6 ~ 3.3 m/s 12 ~ 19 km/h 8 ~ 12 mph 7 ~ 10 knots 3.4 ~ 5.4 m/s 20 ~ 28 km/h 13 ~ 17 mph 11 ~ 16 knots 5.5 ~ 7.9 m/s 29 ~ 38 km/h 18 ~ 24 mph 17 ~ 21 knots 8.0 ~ 10.7 m/s 39 ~ 49 km/h 25 ~ 30 mph 22 ~ 27 knots 10.8 ~ 13.8 m/s 50 ~ 61 km/h 31 ~ 38 mph 28 ~ 33 knots 13.9 ~ 17.
FEELS LIKE Feels Like Temperature shows what the outdoor temperature will feel like. It’s a collective mixture of Wind Chill factor (18°C or below) and the Heat Index (26°C or above). For temperatures in the region between 18.1°C to 25.9°C where both wind and humidity are less significant in affecting the temperature, the device will show the actual outdoor measured temperature as Feels Like Temperature.
BAROMETRIC PRESSURE The atmospheric pressure is the pressure at any location of the earth caused by the weight of the column of air above it. One atmospheric pressure refers to the average pressure and gradually decreases as altitude increases. Meteorologists use barometers to measure atmospheric pressure. Since variation in atmospheric pressure greatly affected by weather, it is possible to forecast the weather by measuring the changes in pressure.
LIGHT INTENSITY, UV INDEX & SUNBURN TIME This section of display show the sunlight intensity, UV index and sunburn time. Press the [ SUN ] key to change the mode. LIGHT INTENSITY MODE: 1. During light intensity mode, press and hold [ SUN ] key for 2 seconds to enter unit setting 2. press [ ] or [ ] key change the unit in sequence: Klux → Kfc → W/m². 3. Press [ SUN ] key to confirm and exit the setting. UV INDEX MODE: To show the currect UV index detected by the outdoor sensor.
TO CLEAR THE MAX/MIN RECORDS Press and hold [ MAX / MIN ] key for 2 seconds to reset the current on display MAX or MIN records. NOTE: The LCD will also display the " "/" ", " " icon, data records time & date. PAST 24 HOURS HISTORY DATA The console automatically stores the weather data of the past 24 hours. 1. Press [ HISTORY ] key to check the beginning of the current hour's weather data, e.g. the current time is 7:25 am, March 8, the display will show the data of 7:00am, March 8. 2.
3. 4. 5. 6. Press [ ] or [ ] key to adjust the value or press and hold the key to change rapidly. Press [ ALERT ] key to confirm the value. Press [ ALARM ] key to toggle the regarding alert on / off. Press [ ALERT ] key to shift to next alert reading. High / Low Alert on Alert off Alert on Alert off 7. Press any key on the front side to save alert on /off status and back to normal mode, or it will automatically back to normal mode after 30 seconds without pressing any key.
WIRELESS 7-IN-1 SENSOR MAINTNANCE CLEANING THE RAIN COLLECTOR 1. Rotate the rain collector by turning it 30°anti-clockwise. 2. Gently remove the rain collector. 3. Clean and remove any debris or insects. 4. Install the collector when it is clean and fully dried. REPLACE THE WIND VANE Unscrew and remove the wind vane for replacement REPLACE THE WIND CUP 1. Unscrew and remove the top cap 2.
Temperature reading too high in the day time 1. Check the ventilation fan inside the radiation shield to make sure it can work properly. 2. Make certain that the sensor array is not too close to heat generating sources or strictures, such as buildings, pavement, walls or air conditioning units. SPECIFICATIONS CONSOLE General Specification Dimensions (W x H x D) 215 x 172 x 29mm (8.5 x 6.8 x 1.1in) Weight 639g (with batteries) Main power DC 5V, 1A adaptor Backup battery 3 x AAA size 1.
(700 ~ 1100hPa ± 5hPa) / (540 ~ 696hPa ± 8hPa) (20.67 ~ 32.48inHg ± 0.15inHg) / (15.95 ~ 20.55inHg ± Accuracy 0.24inHg) (525 ~ 825mmHg ± 3.8mmHg) / (405 ~ 522mmHg ± 6mmHg) Typical at 25°C (77°F) Resolution 1hPa / 0.01inHg / 0.
Rain Display & Function Specification Note: The following details are listed as they are displayed or operate on the console. Unit for rainfall mm and in Accuracy for rainfall ± 7% or 1 tip Range of rainfall 0 ~ 19999mm (0 ~ 787.3 in) Resolution 0.
Transmission interval Operating range --12 seconds for UV, light intensity, wind speed and wind direction data --24 seconds for temperature, humidity and rain data -40 ~ 60°C (-40 ~ 140°F) Lithium batteries required WIRELESS THERMO-HYGRO INDOOR SENSOR Dimensions (W x H x D) Weight Main power Weather data RF transmission range RF frequency (depend on country version) Transmission interval Operating range 60 x 113 x 39.5mm (2.4 x 4.4 x 1.6in) 144g (with batteries) 2 x AA size 1.