Optical heart rate sensor OHR-30 Parts names Wrist band Optical sensor Button Contact LED indicator 1. Before use: How to charge 2. Pairing 3. Using the optical heart rate sensor Handling and Support Copyright© 2020 CATEYE Co,.Ltd.
OHR-30 1. Before use: How to charge Be sure to charge it before use, according to the instructions “How to charge” and “Charging precautions”. Handling the rechargeable battery Caution! Charging precautions • Avoid charging under direct sunlight or in a vehicle parked under direct sunlight, and make sure to charge only when the ambient temperature is between 5 and 40°C. • Before charging, be sure that no dust or other foreign objects are attached to the USB plug.
1. Attach the USB charging cable connector to the contact of the heart rate sensor, and charge using a PC or a commercially available USB charger. Caution! Be careful that metal objects do not touch the contacts of the charging cable connector. This could lead to an electrical short circuit and damage the device. - The indicator turns red and charging starts. The indicator turns blue to indicate that charging is complete. USB charging cable connector Contact LED indicator Standard charging time Approx.
OHR-30 1. Before use: How to charge 2. Pairing Important This section explains how to pair the smart computer and the sensor using the “Cateye Cycling™” smartphone app. To pair the sensor directly to the computer without a smartphone, refer to your computer’s online manual or instruction manual. The Cateye Cycling™ smartphone app (free) must be installed on the smartphone to be used in advance.
Pairing via Bluetooth Smartphone Important Perform pairing at a distance of no more than 3 m. 1. Verify that [Connect] is set to ON in the (MENU), and then tap [Device]. Tap [Pair to Device] to start pairing. 2. Press the heart rate sensor button to transmit the signal. The indicator flashes blue. Press LED indicator When Cateye Cycling™ detects the sensor signal, a message will be displayed on the smartphone. Tap [Pair to Device].
3. After pairing is complete, turn off the power of the heart rate sensor. Press and hold the heart rate sensor button, and release your finger when the LED indicator turns red. Important • When using the smart computer in Sensor Direct Mode: Connect the smart computer to Cateye Cycling™, and then transmit the paired sensor information.
OHR-30 1. Before use: How to charge 2. Pairing 3. Using the optical heart rate sensor Wear the optical heart rate sensor on your arm. Before wearing the heart rate sensor Warning!!! Never use this device if you are using a pacemaker. • Secure the sensor appropriately using the wrist band so that the optical sensor part makes close contact with the skin. • If an allergic reaction or skin inflammation occurs during use, stop using immediately, and consult with a doctor.
Wrist band * Ensure that the optical sensor part is in close contact with your body. * If the heart rate cannot be measured correctly, try again by wearing on a different area (wrist, forearm, upper arm). 3. After measurement is complete, turn off the power of the heart rate sensor. Press and hold the heart rate sensor button, and release your finger when the LED indicator turns red. Copyright© 2020 CATEYE Co,.Ltd.
Handling and Support Optical heart rate sensor OHR-30 Warning!!! / Caution! Warning!!! Never use this device if you use a pacemaker. Caution! Be careful that metal objects do not touch the contacts of the charging cable connector of the optical sensor. This could lead to an electrical short circuit and damage the device.
Specifications Batteries used Lithium-ion polymer battery 50 mAh Continuous operating Approx. 8 – 10 hours time * The continuous operating time is approximate and will vary according to environmental and user conditions. Standard charging time Approx. 1.5 hours * The standard charging time is approximate and will vary according to environmental conditions during charging.
Product warranty 2-year guarantee Sensor unit (Accessories and battery deterioration excluded) CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Industry Canada Statement This device complies with Industry Canada licence‐exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.